Deriving fuel-based emission factor thresholds to interpret heavy-duty vehicle roadside plume measurements

Remote sensing devices have been used for decades to measure gaseous emissions from individual vehicles at the roadside. Systems have also been developed that entrain diluted exhaust and can also measure particulate matter (PM) emissions. In 2015, the California Air Resources Board (CARB) reported that 8% of in-field diesel particulate filters (DPF) on heavy-duty (HD) vehicles were malfunctioning and emitted about 70% of total diesel PM emissions from the DPF-equipped fleet. A new high-emitter problem in the heavy-duty vehicle fleet had emerged. Roadside exhaust plume measurements reflect a snapshot of real-world operation, typically lasting several seconds. In order to relate roadside plume measurements to laboratory emission tests, we analyzed carbon dioxide (CO₂), oxides of nitrogen (NO_X), and PM emissions collected from four HD vehicles during several driving cycles on a chassis dynamometer. We examined the fuel-based emission factors corresponding to possible exceedances of emission standards as a function of vehicle power. Our analysis suggests that a typical HD vehicle will exceed the model year (MY) 2010 emission standards (of 0.2 g NO_X/bhp-hr and 0.01 g PM/bhp-hr) by three times when fuel-based emission factors are 9.3 g NO_X/kg fuel and 0.11 g PM/kg using the roadside plume measurement approach. Reported limits correspond to 99% confidence levels, which were calculated using the detection uncertainty of emissions analyzers, accuracy of vehicle power calculations, and actual emissions variability of fixed operational parameters. The PM threshold was determined for acceleration events between 0.47 and 1.4 mph/sec only, and the NO_X threshold was derived from measurements where after-treatment temperature was above 200°C. Anticipating a growing interest in real-world driving emissions, widespread implementation of roadside exhaust plume measurements as a compliment to in-use vehicle programs may benefit from expanding this analysis to a larger sample of in-use HD vehicles.

Implications: Regulatory agencies, civil society, and the public at large have a growing interest in vehicle emission compliance in the real world. Leveraging roadside plume measurements to identify vehicles with malfunctioning emission control systems is emerging as a viable new and useful method to assess in-use performance. This work proposes fuel-based emission factor thresholds for PM and NOx that signify exceedances of emission standards on a work-specific basis by analyzing real-time emissions in the laboratory. These thresholds could be used to prescreen vehicles before roadside enforcement inspection or other inquiry, enhance and further develop emission inventories, and potentially develop new requirements for heavy-duty inspection and maintenance (I/M) programs, including but not limited to identifying vehicles for further testing.     

Relationships between lichen community composition and concentrations of NO2 and NH3

The relationship between different features of lichen communities in Quercus robur canopies and environmental variables, including concentrations of NO₂ and NH₃ was investigated. NO₂ concentration was the most significant variable, it was positively correlated with the proportion of lichen cover comprising nitrophytes and negatively correlated with total lichen cover. None of the lichen community features were correlated with NH₃ concentrations, which were relatively low across the site. Since nitrophytes and nitrophobes are likely to react in opposite directions to nitrogenous compounds, total lichen cover is not a suitable indicator for these pollutants. It is, therefore, suggested that the proportion of lichen cover comprising nitrophytes may be a suitable simple indicator of air quality, particularly in locations where the pollution climate is dominated by oxides of nitrogen.     

Factors Influencing Prymnesium parvum Population Dynamics During Bloom Initiation: Results from In-lake Mesocosm Experiments1

Roelke, Daniel L., Leslie Schwierzke, Bryan W. Brooks, James P. Grover, Reagan M. Errera, Theodore W. Valenti, Jr., and James L. Pinckney, 2010. Factors Influencing Prymnesium parvum Population Dynamics During Bloom Initiation: Results from In-Lake Mesocosm Experiments. Journal of the American Water Resources Association (JAWRA) 46(1):76-91. DOI: 10.1111/j.1752-1688.2009.00392.x Abstract: The alga Prymnesium parvum forms large fish-killing blooms in many Texas lakes. In some of these lakes, however, P. parvum occurs but does not develop blooms. In this study, we investigated factors that may influence bloom initiation by conducting a series of in-lake experiments involving mixing of waters from Lake Whitney, which has a history of P. parvum blooms, with waters from Lake Waco where no blooms have occurred. In all experiments, the addition of Lake Waco waters resulted in a poorer performance of P. parvum. Various experimental treatments and field data show that differences in grazing, pathogens, nutrients, and salts between the two lakes were not likely factors that contributed to this observation. Industrial and agricultural contaminants, allelochemicals and algicidal chemicals were not measured as a part of this research. However, anthropogenic contaminants other than nutrients were not observed at levels exceeding water quality standards in Lake Waco in recent years. On the other hand, nuisance cyanobacteria are common in Lake Waco, where Microcystis sp. and Anabaena sp. were abundant during the initiation of our experiments, both taxa are known to produce chemicals with allelopathic properties. In addition, the emergent field of algal-heterotrophic bacteria interactions suggests that chemicals produced by heterotrophic bacteria should not be overlooked. Further research focusing on the chemical interactions between cyanobacteria and P. parvum, as well as the potential role of algicidal bacteria, in the initiation of P. parvum blooms is necessary, as it may be important to the management of these blooms.     

Establishing ozone flux–response relationships for winter wheat: Analysis of uncertainties based on data for UK and Polish genotypes

The work outlined in this paper had three objectives. The first was to explore the effects of ozone pollution on grain yield and quality of commercially-grown winter wheat cultivars. The second was to derive a stomatal ozone flux model for winter wheat and compare with those already developed for spring wheat. The third was to evaluate exposure- versus flux–response approaches from a risk assessment perspective, and explore the implications of genetic variation in modelled ozone flux.Fifteen winter wheat cultivars were grown in open-top chambers where they were exposed to four levels of ozone. During fumigation, stomatal conductance measurements were made over the lifespan of the flag leaf across a range of environmental conditions. Although significant intra-specific variation in ‘ozone sensitivity’ (in terms of impacts on yield) was identified, yield was inversely related (R² = 0.63, P < 0.001) to the accumulated hourly averaged ozone exposure above 40 ppb during daylight hours (AOT40) across the dataset. The adverse effect of ozone on yield was principally due to a decline in seed weight. Algorithms defining the influence of environmental variables on stomatal uptake were subtly different from those currently in use, based on data for spring wheat, to map ozone impacts on pan-European cereal yield. Considerable intra-specific variation in phenological effects was identified. This meant that an ‘average behaviour’ had to be derived which reduced the predictive capability of the derived stomatal flux model (R² = 0.49, P < 0.001, 15 cultivars included). Indeed, given the intra-specific variability encountered, the flux model that was derived from the full dataset was no better in predicting O₃ impacts on wheat yield than was the AOT40 index. The study highlights the need to use ozone risk assessment tools appropriate to specific vegetation types when modelling and mapping ozone impacts at the regional level.     

Comparison of selected nutrients and bacteria from common contiguous soils inside and outside swine lagoon effluent spray fields after long-term use

Swine (Sus scofa domestica) lagoon effluent is a valuable resource. In the U.S. Mid-South it is applied from April to September to fertilize grass hay in spray-irrigated fields. Lagoon levels of nutrients and bacteria, and soil levels of nutrients have been documented, but little was known of effluent bacterial levels in soil. The present study examined levels of selected effluent bacteria and nutrients in soils inside and outside spray fields after >15 yr of effluent irrigation. Samples were collected February to March 2009 from contiguous soils spanning adjacent irrigated and nonirrigated areas. Separate soil cores for bacterial and nutrient tests were collected in pairs <10 cm apart. Five cores each were collected at 15-m intervals and combined, respectively, to comprise inside and outside samples from each of 20 soils (four each from five farms/spray fields). Analyses of data combined across all soils showed higher pH and Mehlich-3-extracrable (M3-) P, Mg, K, Na, Cu, and Zn inside than outside spray fields, while total N, total C, M3-Ca, and M3-Mn did not differ. Bacterial levels were higher inside than outside spray fields for heterotrophic plate counts, thermotolerant coliforms, Staphylococcus spp., and Clostridium perfringens, but levels of Escherichia coli and Enterococcus spp. were not different. Cultural presence/absence tests for three pathogens (Listeria spp., Campylobacter spp., and Salmonella spp.) detected only Listeria spp., which did not differ inside (23% positive samples) and outside (28% positive). Molecular tests detected all three pathogens at low levels that were not different inside and outside. We found no evidence of cumulative buildup of Campylobacter spp., Listeria spp., or Salmonela s. in spray field soils.     

Assessing inter-laboratory comparability and limits of determination for the analysis of cyclic volatile methyl siloxanes in whole Rainbow Trout (Oncorhynchus mykiss)

Cyclic volatile methyl siloxanes (cVMS) are high volume production chemicals used in a wide range of industrial and consumer products. Three cVMS compounds (D4, D5, and D6) have and are undergoing environmental risk evaluations in several countries and have been proposed for legal regulation in Canada. As interest in monitoring concentrations of these chemicals in the environment increase, there is a need to evaluate the analytical procedures for cVMS in biological matrices in order to assess the quality of data produced. The purpose of this study was to determine laboratory testing performance for measuring residues of D4, D5, and D6 in a standard set of fish homogenate samples and to estimate limits of determination for each substance. The samples sent to each laboratory consisted of homogenized whole body tissues of hatchery raised rainbow trout which were fed food fortified with D4, D5, and D6 (dosed) and trout that were fed standard food rations (control). The participants analyzed each sample using their analytical method of choice using their own standards and procedures for quantification and quality control. With a few exceptions, participating laboratories generated comparable results for D4, D5, and D6 in both the dosed and control samples having z-scores between 2 and −2. Method detection limits for the whole fish matrix were on average 2.4 ng g⁻¹ ww for D4, 2.3 ng g⁻¹ ww for D5, and 1.8 ng g⁻¹ ww for D6.     

Hydrogen peroxide stabilization in one-dimensional flow columns

Rapid hydrogen peroxide decomposition is the primary limitation of catalyzed H(2)O(2) propagations in situ chemical oxidation (CHP ISCO) remediation of the subsurface. Two stabilizers of hydrogen peroxide, citrate and phytate, were investigated for their effectiveness in one-dimensional columns of iron oxide-coated and manganese oxide-coated sand. Hydrogen peroxide (5%) with and without 25 mM citrate or phytate was applied to the columns and samples were collected at 8 ports spaced 13 cm apart. Citrate was not an effective stabilizer for hydrogen peroxide in iron-coated sand; however, phytate was highly effective, increasing hydrogen peroxide residuals two orders of magnitude over unstabilized hydrogen peroxide. Both citrate and phytate were effective stabilizers for manganese-coated sand, increasing hydrogen peroxide residuals by four-fold over unstabilized hydrogen peroxide. Phytate and citrate did not degrade and were not retarded in the sand columns; furthermore, the addition of the stabilizers increased column flow rates relative to unstabilized columns. These results demonstrate that citrate and phytate are effective stabilizers of hydrogen peroxide under the dynamic conditions of one-dimensional columns, and suggest that citrate and phytate can be added to hydrogen peroxide before injection to the subsurface as an effective means for increasing the radius of influence of CHP ISCO.     

Reporting central tendencies of chamber measured surface emission and oxidation

Methane emissions, concentrations, and oxidation were measured on eleven MSW landfills in eleven states spanning from California to Pennsylvania during the three year study. The flux measurements were performed using a static chamber technique. Initial concentration samples were collected immediately after placement of the flux chamber. Oxidation of the emitted methane was evaluated using stable isotope techniques. When reporting overall surface emissions and percent oxidation for a landfill cover, central tendencies are typically used to report “averages” of the collected data. The objective of this study was to determine the best way to determine and report central tendencies. Results showed that 89% of the data sets of collected surface flux have lognormal distributions, 83% of the surface concentration data sets are also lognormal. Sixty seven percent (67%) of the isotope measured percent oxidation data sets are normally distributed. The distribution of data for all eleven landfills provides insight of the central tendencies of emissions, concentrations, and percent oxidation. When reporting the “average” measurement for both flux and concentration data collected at the surface of a landfill, statistical analyses provided insight supporting the use of the geometric mean. But the arithmetic mean can accurately represent the percent oxidation, as measured with the stable isotope technique. We examined correlations between surface CH₄ emissions and surface air CH₄ concentrations. Correlation of the concentration and flux values using the geometric mean proved to be a good fit (R² = 0.86), indicating that surface scans are a good way of identifying locations of high emissions.     

Innovative applications of subgrade biogeochemical reactors: Three case studies

Subgrade biogeochemical reactors (SBGRs) are an in situ remediation technology shown to be effective in treating contaminant source areas and groundwater hot spots, while being sustainable and economical. This technology has been applied for over a decade to treat chlorinated volatile organic compound source areas where groundwater is shallow (e.g., less than approximately 30 feet below ground surface [ft bgs]). However, this article provides three case studies describing innovative SBGR configurations recently developed and tested that are outside of this norm, which enable use of this technology under more challenging site conditions or for treatment of alternative contaminant classes. The first SBGR case study addresses a site with groundwater deeper than 30 ft bgs and limited space for construction, where an SBGR column configuration reduced the maximum trichloroethene (TCE) groundwater concentration from 9,900 micrograms per liter (μg/L) to <1 μg/L (nondetect) within approximately 15 months. The second SBGR is a recirculating trench configuration that is supporting remediation of a 5.7‐acre TCE plume, which has significant surface footprint constraints due to the presence of endangered species habitat. The third SBGR was constructed with a new amendment mixture and reduced groundwater contaminant concentrations in a petroleum hydrocarbon source area by over 97% within approximately 1 year. Additionally, a summary is provided for new SBGR configurations that are planned for treatment of additional classes of contaminants (e.g., hexavalent chromium, 1,4‐dioxane, dissolved explosives constituents, etc.). A discussion is also provided describing research being conducted to further understand and optimize treatment mechanisms within SBGRs, including a recently developed sampling approach called the aquifer matrix probe.     

Research priorities for managing the impacts and dependencies of business upon food,energy, water and the environment

Delivering access to sufficient food, energy and water resources to ensure human wellbeing is a major concern for governments worldwide. However, it is crucial to account for the ‘nexus’ of interactions between these natural resources and the consequent implications for human wellbeing. The private sector has a critical role in driving positive change towards more sustainable nexus management and could reap considerable benefits from collaboration with researchers to devise solutions to some of the foremost sustainability challenges of today. Yet opportunities are missed because the private sector is rarely involved in the formulation of deliverable research priorities. We convened senior research scientists and influential business leaders to collaboratively identify the top forty questions that, if answered, would best help companies understand and manage their food-energy-water-environment nexus dependencies and impacts. Codification of the top order nexus themes highlighted research priorities around development of pragmatic yet credible tools that allow businesses to incorporate nexus interactions into their decision-making; demonstration of the business case for more sustainable nexus management; identification of the most effective levers for behaviour change; and understanding incentives or circumstances that allow individuals and businesses to take a leadership stance. Greater investment in the complex but productive relations between the private sector and research community will create deeper and more meaningful collaboration and cooperation.