Co-treatment of hydrogen sulfide and methanol in a single-stage biotrickling filter under acidic conditions

Biofiltration of waste gases is cost-effective and environment-friendly compared to the conventional techniques for treating large flow rates of gas streams with low concentrations of pollutants. Pulp and paper industry off-gases usually contain reduced sulfur compounds, such as hydrogen sulfide and a wide range of volatile organic compounds (VOCs), e.g., methanol. It is desirable to eliminate both of these groups of compounds. Since the co-treatment of inorganic sulfur compounds and VOCs in biotrickling filters is a relatively unexplored area, the simultaneous biotreatment of H2S and methanol as the model VOC was investigated. The results showed that, after adaptation, the elimination capacity of methanol could reach around 236 g m(-3) h(-1) with the simultaneous complete removal (100%) of 12 ppm H2S when the empty bed residence time is 24 s. The pH of the system was around 2. Methanol removal was hardly affected by the presence of hydrogen sulfide, despite the low pH. Conversely, the presence of the VOC in the waste gas reduced the efficiency of H2S biodegradation. The maximal methanol removal decreased somewhat when increasing the gas flow rate. This is the first report on the degradation of methanol at such low pH in a biotrickling filter and on the co-treatment of H2S and VOCs under such conditions.     

Structure of Mn-Zr mixed oxides catalysts and their catalytic performance in the gas-phase oxidation of chlorocarbons

The catalytic activity and selectivity of manganese zirconia mixed oxides were evaluated for the oxidation of two common chlorinated pollutants found in waste streams, namely 1,2-dichloroethane (DCE) and trichloroethylene (TCE). Mixed oxides with varying Mn-Zr content were prepared by coprecipitation via nitrates, and subsequent calcination at 600 degrees C for 4 h in air. These catalysts were characterised by means of several techniques such as atomic emission spectrometry, N2 adsorption-desorption, powder X-ray diffraction, temperature-programmed desorption of ammonia, pyridine adsorption followed by diffuse reflectance infrared spectroscopy and temperature-programmed reduction with hydrogen. The active catalytic behaviour of Mn-Zr mixed oxides was ascribed to a substantial surface acidity combined with readily accessible active oxygen species. Hence, the mixed oxide with 40 mol% manganese content was found to be an optimum catalyst for the combustion of both chlorocarbons with a T50 value around 305 and 315 degrees C for DCE and TCE oxidation, respectively. The major oxidation products were carbon dioxide, hydrogen chloride and chlorine. It was observed that the formation of both CO2 and Cl2 was promoted with Mn loading.     

Effect of pre-treatment and supporting media on Ni(II), Cu(II), Al(III) and Fe(III) sorption by plant root material

In this work Paspalum notatum root material was used to elucidate the influence of acid leaching pre-treatment and of sorption medium on metal adsorption. Ground P. notatum root was leached with 0.14M HNO(3). Leached root material (LRM) and non-leached root material (NLRM) were employed to flow sorption of Ni(II), Cu(II), Al(III) and Fe(III) in 0.5M CH(3)COONH(4) medium at pH 6.5. For LRM the sorption was also studied in 0.5M KNO(3) medium. The acid pre-treatment increased the sorption capacity (SC) for all ions studied. For the KNO(3) medium, Cu(II) and Fe(III) sorption was higher than in CH(3)COONH(4) and the type of the Ni(II) isotherm's model changed. The Freundlich model was the most representative isotherm model to describe metallic ions sorption. The (1)H NMR spectra showed differences between LRM and NLRM and the acid-basic potentiometric titration elucidated that acid-leaching procedure affected the root material sorption sites once only two predominant sorption sites were found for LRM (phenolic and amine, both able cations sorption) and five sorption sites (two carboxylic, amine and two phenolic) were founded for NLRM.     

Heavy metal-rich wastes sequester in mineral phases through a glass-ceramic process

Certain sludges generated by industry are rich in contaminating elements and are a major environmental problem. In this study, we determine the ability of these contaminating elements to be incorporated into a glass-matrix and in various mineral phases after a crystallization process. The contaminating elements studied were obtained from sewage sludges (SS) and galvanic sludges (GS), our raw materials. The sludge samples were taken from urban wastewater treatment plant in Catalonia (NE Spain) with high levels of phosphorus oxide (P(2)O(5)). In silica glasses, P(2)O(5) acts as a network former. We determined the chemical composition of both the SS and GS, as well as their thermal behaviour by differential thermal analysis and thermal gravimetric analysis (DTA-TG) to obtain their melting curves. The vitreous transition temperature of the obtained glass was established by dilatometer technique at 725 degrees C. The DTA-TG curve of the glass obtained has an exothermal wide peak at 860 degrees C corresponding to crystallization of the two phases: a spinel phase and a phosphate phase. A second exothermal wide peak at 960 degrees C was attributed to the crystallization of aluminium pyroxene, anorthite and fluor-apatite, with two exothermal phenomena attributed to the evolution of these phases. An exothermal peak at 1100 degrees C was attributed to gehlenite crystallization. Scanning electron microscope observations and energy-dispersed X-ray spectroscopy microanalyses of glass-ceramic showed that the contaminating elements were concentrated in the spinel phases, which are the first phases to crystallize during the cooling of glass. Finally, the spinel structure permits the incorporation of all the contaminating elements into it.     

Trends in background levels of persistent organic pollutants at Kosetice observatory, Czech Republic.2) Part II. Aquatic and terrestrial environments 1996-2005

A multimedia sampling of ambient air, wet deposition, surface water, sediment, soil and biota has been performed at Kosetice background observatory in the southern Czech Republic since 1988. An integrated monitoring approach was applied to assess the current state, anthropogenic impacts, and possible future changes of terrestrial and freshwater environments. Average PCB concentrations in the individual matrices calculated from ten years of sampling on multiple sites varied between 2 ng g(-1) in sediment and 7 ng g(-1) in soil or moss. DDT concentrations were lower in moss and needles (2 ng g(-1) and 4 ng g(-1), respectively) than in sediment (11 ng g(-1)) and soil (20 ng g(-1)), while the HCH level was higher in moss and needles (5 ng g(-1) and 6 ng g(-1), respectively) than in soil or sediment (1 ng g(-1) and 2 ng g(-1), respectively). The highest average level of PAHs was found in soil (600 ng g(-1)), while it was lower in needles (230 ng g(-1)), moss (210 ng g(-1)) or sediment (210 ng g(-1)). Time related trends of concentration levels of persistent organic pollutants in all matrices were investigated. Moss and needle trend patterns resembled those of the ambient air, showing a slight concentration decrease of all compounds, except for hexachlorobenzene. The soil, water and sediment concentrations showed a similar decrease of PAHs, PCBs, and HCHs, but there was no clear trend for DDTs and HCB.     

Determination of selected quaternary ammonium compounds by liquid chromatography with mass spectrometry. Part I. Application to surface, waste and indirect discharge water samples in Austria

A method for simultaneous quantitative determination of alkyl benzyl, dialkyl and trialkyl quaternary ammonium compounds (QACs) has been developed, validated and subsequently applied to real water samples in Austria. The method employs liquid-liquid extraction (LLE) followed by liquid chromatography/tandem mass spectrometry (LC-MS/MS), using electrospray ionization (ESI) in positive mode. The overall method quantification limits range from 4 to 19ng/L for the enrichment of 500mL water samples and analyte recoveries are between 80 and 99%. The method was applied to 62 of the respective water samples without filtration to avoid the loss of the analytes due to the high adsorption capacity of these compounds. Maxima in the mg/L range, especially in the wastewater of hospitals and laundries, could be detected for the selected target compounds.     

On the presence of enriched amounts of 235U in hot particles from the terrestrial area affected by the Palomares accident (Spain)

The characterisation by ICP-MS of an isolated Pu-U hot particle originating from the nuclear weapons accident in Palomares (Spain) shows, for the first time, that its uranium content is highly enriched in (235)U. The enrichment has been confirmed by independent analyses of two surface soil samples collected in a heavily contaminated area close to the impact point of one of the bombs. This finding clarifies better the composition of the weapons involved in the accident and is of importance when the inventory of U and Pu in the contaminated area are to be calculated.     

Pyrolysis of mixtures of sewage sludge and manure: a comparison of the results obtained in the laboratory (semi-pilot) and in a pilot plant

A pilot-scale pyrolysis process was carried out for the treatment of a mixture of two types of waste, sewage sludge and cattle manure, comparing the results with others obtained under laboratory conditions (semi-pilot scale). The aim of this study was to obtain the energetic valorization of the products. Owing to the specific characteristics of the plant, two products were obtained from the process: gas and carbonized solid. As no liquid fraction was obtained, the gas fraction is a greater percentage made up of both condensable and non-condensable compounds, which were obtained separately at the laboratory scale. The pilot plant was designed so that the gases produced by thermolysis were burnt continuously in a combustion chamber, while the carbonized fraction was fed in batches for co-combustion. To determine composition and combustion ability, the gas and solid products from the pilot process were characterized by chromatographic analysis of the gaseous fraction and chemical analysis and programmed-temperature combustion of the carbonized solid. The composition of the combustion gases, rich in light hydrocarbons, and the carbon present in the carbonized fraction enable the energetic valorization of these products. The combustion gases were subjected to a cleaning process and their composition analysed twice: before and after the gas cleaning treatment. The study led to a positive assessment of the possible use of the process products as fuel, provided that the combustion gases are treated. As most of the sulphur and chlorine from the original waste are mainly concentrated in the solid fraction, the use of char as a fuel will depend on the effectiveness of clean-up techniques for combustion gases. During gas cleansing, neutralizing with sodium bicarbonate proved effective, especially for the acidic compounds HCl, HF and SO(2).     

Comparison of different collection systems for sorted household waste in Sweden

Composition and quantity per person of municipal solid waste (MSW) have been analyzed in six municipalities in southern Sweden with similar socio-economic conditions but with different collection systems. Samples of residual waste have been sorted, classified and weighed in 21 categories during 26 analyses that took place from 1998-2004. Collection data of the total waste flow, including source sorted recycling materials, in the same area have been compiled and compared. Multivariate data analyses have been applied. Weight-based billing reduced delivered amounts of residual household waste by 50%, but it is unknown to what extent improper material paths had developed. With curbside collection more metal, plastic and paper packaging was separated and left to recycling. When separate collection of biodegradables was included in the curbside system, the overall sorting of dry recyclables increased. The large uncertainty associated with waste composition analyses makes it difficult to draw strong conclusions regarding the effects on specific recyclables or the changes in the composition of the residual waste.     

Chemical and biological characterization of slaughterhouse wastes compost

The chemical and biological properties of compost made from yard trimmings (YT) composted alone or mixed with slaughterhouse wastes (SHW) were evaluated in seven phases. Mixtures were weighed in a 2:1 proportion (YT:SHW) and placed in composting bins (0.91 m2). Temperature was recorded to determine the time (d) needed to reach the first (1HC) and second heat cycles (2HC). Composting characteristics were measured at 0 d, at the peak of the 1HC and 2HC, and at maturation (0, 20, 50 and 70 d). During 1HC, bacterial isolates were cultivated in both treatments and identified using the Biolog System. Chemical composition was statistically analyzed using a 2 (layers of SHW)x7 (composting phases) factorial arrangement of treatments with the ANOVA procedure of SAS. The pH was neutral for YT and ranged from 7.41 to 6.82 for SHW throughout the process. There was a decrease in organic matter (OM) and carbon (C), and a relative increase in nitrogen (N) in both treatments. At 70 d of maturation, C:N values were similar between treatments, but lower (P>0.05) than the initial values. Final N concentration was higher (P>0.05) for the treatment with SHW. Only the SHW treatment exhibited thermophilic temperatures. At the 1HC in both treatments, different populations of bacteria responsible for the breakdown of OM were identified showing an active heterogeneous population. The presence of pathogenic microorganisms was not detected in treatments containing SHW.