采用支持向量机算法优化电化学处理油田污水的工艺参数

采用支持向量机(SVM)算法,将Box-Behnken设计法与支持向量回归算法(SVR)实验参数优化软件相结合,优化电化学去除油田污水COD的工艺参数。通过量子粒子群算法对SVM算法参数进行优化,从建立的回归模型中找到工艺参数的全局最佳点:电解时间60 min,电解电流3 A,三维电极填充料中石英砂质量695 g。模型得到的COD理论最优去除率为92.48%,验证实验得到的COD去除率为91.43%。     

海上含聚污水电化学处理装置的优化

为解决传统电化学方法在含聚污水处理时电极板消耗严重、絮渣量大的问题,通过改进电极板材料、组合数及结构等,研究适度降解-除油一体化电化学技术,在降低渣泥量的同时保证处理效果。实验结果表明:最佳电极板组合为"网状惰性金属复合物极板(阳)-网状铝极板(阴)-网状铝极板(阴)-网状惰性金属复合物极板(阳)";在电解电流为4.0 A、极板间距为8.0 cm、面体比(电极板面积与处理污水量的比值)为2/17 cm~2/mL、电解时间为30 min的最佳处理条件下,几乎无絮渣产出,含聚污水的浊度去除率为93.3%、聚合物降解率为92.0%、除油率为95.0%,展现了优良的处理效果。     

Hydrothermal liquefaction phase behavior of microalgae & model compounds in fused silica capillary reactor

A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation.     

Preparation of biochar catalyst with saccharide and lignocellulose residues of corncob degradation for corncob hydrolysis into furfural

This paper presented a novel process for production of furfural by hydrothermal degradation of corncob over biochar catalyst, in which it was prepared with the recycling degradation solution and lignocellulosic solid residues. The biochar catalyst was papered by lignocellulose residues and concentrated saccharide solution, and then impregnated in 0.5 mol/L sulphuric acid at room temperature for 24 h assisted by the ultrasonic vibration. In the system of recycling, 8.8 % lignocellulose residues and 100 % concentrated saccharide solution from corncob hydrolysis have been recycled. Hydrolysis of corncob was carried out at 180 °C for duration of 170 min over the biochar catalyst. The experimental results have shown that the furfural yield of up to 37.75 % and overall corncob conversion rate of 62.00 % could be achieved under optimum operating conditions for the catalysts preparation and the corncob hydrolysis. It is believed that the acid density of 4.27 mmol/g of biochar catalyst makes the SO₃H groups cleave β-1,4 glycosidic linkages effectively and hydrolyze the cellulose and hemicellulose to water-soluble sugars, as well as to facilitate dehydration of xylose to give the product of furfural.     

Life cycle assessment of biodiesel fuel production from waste cooking oil in Okayama City

A life cycle assessment (LCA) is performed to make clear of the actual environment impacts from conversation of waste cooking oil (WCO) to biodiesel fuel (BDF) in Okayama. A scenario analysis is carried out based on different participation rate of residents who separate WCO from general waste, corresponding to different BDF utilisation rate in transportation system. Sub scenarios complying with different gas emission standards regarding vehicles are designed as well. Afterwards, life cycle impact assessment is conducted to focus on global warming, acidification, and urban air pollution. Overall improvement of almost all kinds of life cycle inventories is significant when diesel is replaced with BDF, demonstrating that a shift from WCO-to-incineration to WCO-to-BDF is more beneficial. Under carbon neutral, compared to base scenario (S0), about 746.05 ton CO₂ emission will be reduced annually in the scenario with 100 % BDF utilisation in vehicles (S4). Meanwhile, total external cost in three environmental impacts (EI) sharply reduces by 51.90 %, showing much economic sustainability in S4. Moreover, the manufacturing cost for producing one litter WCO-to-BDF is 97.32 Yen. Sensitivity analysis shows that the gas emission standard regarding vehicles had much bigger effect on EI than BDF manufacturing process in this research.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

High CO2 adsorption on improved ZSM-5 zeolite porous structure modified with ethylenediamine and desorption characteristics with microwave

Journal of Material Cycles and Waste Management - Synthesized zeolite Socony Mobil-5 (ZSM-5) with large pore surface structures and modified with ethylenediamine were used to achieve high CO2...     

Experimental thermal storage research of organic binary phase change materials in building environment

This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment.     

Investigation of titanium liquid/gas diffusion layers in proton exchange membrane electrolyzer cells

In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses.     

羟基乙叉二膦酸镀铜废液的处理及Cu~(2+)的高附加值资源化回收

采用Na BH4还原法将羟基乙叉二膦酸(HEDP)镀铜废液中的Cu~(2+)制备成纳米铜粉,并采用聚丙烯酰胺(PAM)对还原反应后的废液进行絮凝处理。研究了n(Cu~(2+))∶n(Na BH4)、还原反应温度、还原反应时间及PAM添加量对废液中剩余Cu~(2+)质量浓度的影响,并对回收的纳米铜粉进行了XRD和TEM表征。实验结果表明:当n(Cu~(2+))∶n(Na BH4)=4∶6、还原反应温度为50℃、还原反应时间为2 h时,废液中剩余Cu~(2+)质量浓度降低至1.1 mg/L,Cu~(2+)还原率达99.99%;可获得粒径为20~45 nm的近球型、高纯度、由多晶组成的纳米铜粉;当PAM添加量为10 mg/L时,废液中剩余Cu~(2+)质量浓度降至0.35 mg/L以下,达到GB 21900—2008《电镀污染物排放标准》(小于0.5 mg/L)的要求。