Increasing interannual and altitudinal ozone mixing ratios in the Catalan Pyrenees

Interannual, seasonal, daily and altitudinal patterns of tropospheric ozone mixing ratios, as well as ozone phytotoxicity and the relationship with NO_x precursors and meteorological variables were monitored in the Central Catalan Pyrenees (Meranges valley and Forest of Guils) over a period of 5 years (2004–2008). Biweekly measurements using Radiello passive samplers were taken along two altitudinal transects comprised of thirteen stations ranging from 1040 to 2300 m a.s.l. Visual symptoms of ozone damage in Bel-W3 tobacco cultivars were evaluated biweekly for the first three years (2004–2006). High ozone mixing ratios, always above forest and vegetation protection AOT40 thresholds, were monitored every year. In the last 14 years, the AOT40 (Apr–Sept.) has increased significantly by 1047 μg m^?3 h per year. Annual means of ozone mixing ratios ranged between 38 and 67 ppb_v (38 and 74 ppb_v during the warm period) at the highest site (2300 m) and increased at a rate of 5.1 ppb_v year^?1. The ozone mixing ratios were also on average 35–38% greater during the warm period and had a characteristic daily pattern with minimum values in the early morning, a rise during the morning and a decline overnight, that was less marked the higher the altitude. Whereas ozone mixing ratios increased significantly with altitude from 35 ppb_v at 1040 m–56 ppb_v at 2300 m (on average for 2004–2007 period), NO₂ mixing ratios decreased with altitude from 5.5 ppb_v at 1040 m–1 ppb_v at 2300 m. The analysis of meteorological variables and NO_x values suggests that the ozone mainly originated from urban areas and was transported to high-mountain sites, remaining aloft in absence of NO. Ozone damage rates increased with altitude in response to increasing O₃ mixing ratios and a possible increase in O₃ uptake due to more favorable microclimatic conditions found at higher altitude, which confirms Bel-W3 as a suitable biomonitor for ozone concentrations during summer time. Compared to the valley-bottom site the annual means of ozone mixing ratios are 37% larger in the higher sites. Thus the AOT40 for the forest and vegetation protection threshold is greatly exceeded at higher sites. This could have substantial effects on plant life at high altitudes in the Pyrenees.     

The safety observer effect: the effects of conducting safety observations

INTRODUCTION: Some research suggests that conducting safety observations of another's safety performance may serve as an effective tool in increasing the safety performance of the observer. The primary purpose of the present study was to assess the effects of conducting safety observations on the postural safety performance of observers engaging in an assembly task for short time periods. The secondary objectives of the study were: (a) to measure productivity, and (b) to measure the accuracy of participant safety observations. METHOD: An ABC (A: baseline, B: information, C: observation) multiple-baseline design counterbalanced across postural behaviors (back, shoulder, and feet position) was implemented with six participants. RESULTS AND DISCUSSION: Substantial improvements in postural safety occurred after participants conducted safety observations, and these improvements did not appear to negatively affect productivity. Results also suggest that there is no relation between the accuracy of an observer's safety observation and their subsequent safety performance. IMPACT ON INDUSTRY: This research provides evidence that a safety observation process can function to increase safe postural behavior of observers. Thus, the implementation of such a process may contribute to the prevention of musculoskeletal disorders and related costs in the workplace.     

Evaluation of the Spanish hot dip galvanising sector as a source of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans

A survey to estimate the polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) emissions of Spanish hot dip galvanising sector was carried out during 2002. This investigation is the first presenting Spanish experimental data related to this industrial sector. Three different matrices: flue gas, ash and filter dust were tested to quantify the PCDD/Fs generated during the galvanising process. The organic source of PCDD/F formation could be from the insufficient degreasing o from inhibitors or additives used in the pickling steps such as quinoline, isoquinoline, 8-methylquinoline or polyether phosphoric acid. Low levels PCDD/Fs were achieved in air emissions when air control devices are used. On the contrary, filter dusts are highly contaminated; indicating that the absence of air control devices would increase the risk of fugitive emissions. Homologue profiles and Principal Component Analysis demonstrate there are differences in the formation mechanisms in the bath zone (ashes) compared to the stack location (filter dusts and air emissions), related to the de novo synthesis and reaction time. The annual PCDD/F emission to the atmosphere for this sector during 2002 has been estimated in 0.023g I-TEQ. The emission factor of plants with air control devices has been calculated at 0.030microg I-TEQ/ton of galvanised steel.     

Performance evaluation of a biotrickling filter treating a mixture of oxygenated VOCs during intermittent loading

Laboratory scale-studies on the biodegradation of a 1:1:1 weight mixture of three oxygenated volatile organic compounds (VOCs), ethanol, ethyl acetate, and methyl-ethyl ketone (MEK) in a biotrickling filter (BTF) were carried out using two identically sized columns, filled with different polypropylene rings. The performance of the BTFs was examined for a period of 10 months applying several operational strategies. Similar performance was obtained for both supports. Intermittent flow rate of trickling liquid was shown beneficial to improve the removal efficiency (RE). Continuous feeding of VOC resulted in an excessive accumulation of biomass so high pressure drop was developed in less than 20-30 d of operation. Intermittent VOC loading with night and weekend feed cut-off periods passing dry air, but without addition of water, was shown as a successful operational mode to control the thickness of the biofilm. In this case, operation at high inlet loads (ILs) was extended for more than 75 d maintaining high REs and low pressure drops. Outlet emission concentrations lower than 100 mg Cm(-3) were obtained for ILs up to 100 g Cm(-3)h(-1) working at 15s of empty bed residence time. The most easily biodegradable compounds ethanol and ethyl acetate were used primarily than MEK. After a 3-wk-starvation period, the system performance was almost restored since the first d of operation, being the removal of the less biodegradable compound, MEK, partially deteriorated.     

Ten years measuring PCDDs/PCDFs in ambient air in Catalonia (Spain)

This work summarizes the results of a ten year surveillance programme on PCDD/F in ambient air carried out in Catalonia (Spain). The study has been conducted by the Dioxin Laboratory of Spanish Council for Scientific Research (CSIC) in collaboration with the Environment Department of the Catalonian Government. 175 samples have been collected throughout Catalonia from 1994 to 2004. Different sampling locations classified as industrial, traffic, urban, suburban and rural sites have been monitored in order to find the most contaminated zones as well as the ones with expected background concentrations. The highest concentrations found in this study were determined at the industrial locations. Concentrations ranging from 5 to 1196 fg I-TEQ/m3, with a mean value of 140 fg I-TEQ/m3 and from 10 to 357 fg I-TEQ/m3, with a mean value of 72 fg I-TEQ/m3 were determined in industrial and traffic sampling points, respectively. In contrast, the lowest concentrations were found in rural stations, ranging from 5 to 45 fg I-TEQ/m3, with a mean value of 28 fg I-TEQ/m3. The PCDD/F concentration trend in Catalonian ambient air shown a clear drop of the median values occurred during the study sampling period. A decline of about 70% was observed from 1997-1998 to 2003-2004.     

Distribution of polycyclic aromatic hydrocarbons (PAHs) and tributyltin (TBT) in Barcelona harbour sediments and their impact on benthic communities

Sediments have long been recognised as a sink for many contaminants like polycyclic aromatic hydrocarbons (PAHs) and tributyltin (TBT), which by virtue of their nature can strongly adsorb onto sediments affecting the benthic community inhabiting them. Using geographical information systems, this study reports and combines the results of several already existing studies along Barcelona harbour in order to assess the potential ecological impacts of these contaminants on the benthos of the harbour ecosystem. Chemical analysis indicated low to moderate contents of PAHs and high contents of TBT in sediments in Barcelona harbour. Comparison against existing sediment quality guidelines (SQGs) indicated that acutely toxic effects would not be expected for PAHs but for TBT, which represents a serious environmental threat for the benthic community. Benthos surveys revealed a deterioration of the benthic community throughout the harbour, especially in the inner port.     

Minimization of the environmental impact of chrome tanning: a new process with high chrome exhaustion

In all tanning technology operations wastes are generated. These reach the environment as residual waters, solid and liquid waste as well as atmospheric emissions and odours.

This study tests an alternative method to the traditional tanning method at an industrial level. The new method is based on tanning without float and by significantly increasing the temperature at the end of the tanning process. The properties of the leathers obtained using the two methods have been compared and the results indicate that those leathers have similar physical, chemical, and organoleptic properties. However, the differences existing from the environmental point of view are significant. It is not necessary to use clean water for this tanning. Moreover, there is a 75% reduction of the residual float, a 91% reduction of the chrome discharged, and a 94% reduction of the chlorides discharged. A financial assessment was carried out to demonstrate that the newly proposed system is 32% more economic than the traditional one.     

Minimization of the environmental impact of chrome tanning: a new process reusing the tanning floats

A chrome tanning process which allows the reuse of tanning floats has been developed. The most commonly used chromium salts were replaced by highly masked and basified ones. This substitution eliminates basification operation and prevents pH change and the considerable neutral salts concentration increase in the tanning float. Consequently, tanning float can be reused several times. An optimum chromium salt concentration in the tanning float between 10% and 12.5% has been determined. It has been shown that the number of times the tanning float can be reused depends on the quality of the leather grain to be manufactured. In the best case, a saving of 18 L of water per kilogram of tanned leather is calculated. This means savings of 90% of water normally used.