Surface Air Pollutant Concentration Frequency Distributions: Implications for Urban Modeling

With the development of ambient air quality standards (AAQS), the need arises to describe the characteristics of regional surface air-pollutant concentration frequency distributions. In the evaluation of land use plans, numerous agencies will be concerned with evaluating the effectiveness of emission zoning and/or control actions. On a regional basis, one means of performing this assessment lies in determining the changes in the pollutant frequency distributions resulting from control actions.

This study presents new data concerning the surface air-pollutant concentration frequency distributions observed for area sources and continuous point sources, and compares these distributions with those of the pertinent meteorological variables describing the transport and diffusion of the pollutant. The observed surface air pollutant frequency distributions are compared to those corresponding to simple modeling concepts from either an urban area source or a continuous point source. For an urban source and a relatively inert pollutant like CO, we found that the observed frequency distribution for CO surface air concentration parallels the approximately log-normal frequency distribution of the reciprocal of the wind speed. We show that the constant relating these two well-correlated frequency distributions can be determined either experimentally or with a numerical simulation model of air pollution. The usefulness of numerical models in air pollution is discussed.     

Results of Field Measurements of Industrial Particulate Sources and Electrostatic Precipitator Performance

This paper presents results of source size distribution measurements over the size range from 0.1 μm to 5 μm for six classes of particulate sources and fractional efficiency measurements on five full scale electrostatic precipitators and one pilot scale precipitator. The precipitators all showed moderately high to high particulate collection efficiencies for particles having diameters larger than a few micrometers or smaller than a few hundredths of a micrometer and a minimum in collection efficiency for particles having diameters of a few tenths of a micrometer.     

An Integrated Program to Achieve Maximum Performance of Electrostatic Precipitators

The objective of this paper is to describe the Tennessee Valley Authority's efforts and plans in designing an operating and maintenance program that will ensure maximum performance of the electrostatic precipitators at our power generating stations. Detailed operating and maintenance manuals are being prepared for each plant for the use of plant personnel. These manuals include instructions on operation, maintenance, and testing of the precipitators. Instructions on internal and external equipment inspections to be performed during unit operation, emergency and scheduled outages, and problem diagnostic procedures are included to help the plant personnel solve problem areas. Performance curves are included in the manuals which show the effect of gas volume flow, gas temperature, gas resistivity, coal changes, and loss of transformer-rectifier sets on the precipitator performance. In addition, opacity monitors that record continuous opacity readings are being installed at all our plants to assist the plant in monitoring precipitator performance. Full-time operating and maintenance crews are being organized at the plants to monitor and maintain the precipitator and ash-removal systems. Also, a staff of technical personnel is being organized at the central office to provide technical advice and assistance in design, operation, and maintenance problems and liaison and coordination for all the plants concerning the precipitators. Periodic precipitator field inspections, performance and operating parameter optimization testing, and review of the equipment operating logs are made by the central office technical personnel. Recommendations and technical assistance are then furnished to the plant with regard to the precipitator overall performance and operating characteristics.     

Some Factors in Minimizing Precipitator Costs

This paper is directed to those individuals involved in design of electrostatic precipitators. The Deutsch-Anderson model is usually employed by industry for the design of electrostatic precipitators. The so-called process design variable in this approach is the total capture area in the precipitator. Unfortunately, little is available on the equipment design of this unit, i.e., the geometric arrangement of the plates that constitute the capture area and the external dimensions of the physical structure that houses the precipitator components. These are important economic considerations, and it is to this subject that this paper is directed. It is relatively easy to predict equipment costs for “off-the-shelf” electrostatic precipitators; it is more difficult to closely predict the cost for a custom-made unit, which is more often the case encountered in practice. Once the capture area is calculated, the total precipitator cost becomes a strong function of the outer casing and outer accessories of the physical system. In this paper, a model is presented that can help minimize precipitator cost. An illustrative example complements the development of the model.     

Heavy Duty Diesel Particulate Emission Factors

For the past several years, EPA has been measuring particulate emissions from a variety of heavy-duty diesel engines through contracts with Southwest Research Institute. Particulate emissions samples have been collected using an exhaust splitter to divert a fraction of the engine exhaust into a standard dilution tunnel. A small fraction of the diluted exhaust from the tunnel is pulled through a filter from which particulate mass and, in some cases, organic content of the particulate is determined. This paper discusses the sampling system and gives particulate emission factors that have been computed from truck and bus fuel consumption data as well as average truck and bus speed data from New York and Los Angeles (freeway and nonfreeway usage). Average particulate emission test results (steady state tests) for 2-stroke engines were 4.74 g/kg fuel and for 4-stroke engines were 2.64 g/kg fuel. Using average particulate emissions results, a particulate emission factor range of 0.8 to 1.3 g/km was computed. Nationwide diesel particulate emissions were calculated to be 88,000 metric tons per year.     

Analysis of an APCA Baghouse Operation and Maintenance Survey

Baghouse operation and maintenance is probably the most serious problem area of fabric filter operations. Committee TC-1 (Particulates) of the Air Pollution Control Association recently surveyed baghouse installations in'the United States for the purpose of gathering information on operation and maintenance procedures and problems. One hundred thirty-three questionnaires were completed and returned. In this paper, the results of a comprehensive analysis of these data are described and interpreted. A multiple-choice type of compilation of the responses has been used to permit statistical interpretation of the results. Due to the length of the questionnaire and the tables which resulted from the analysis, these are described but not included in the following paper. They are available from the TC-1 Committee c/o APCA.     

Factors Influencing the Emissions of Nitrated-Polynuclear Aromatic Hydrocarbons(Nitro-PAH) from Diesel Engines

The potential problem of 1-nitropyrene (1-NP) formation during filter sampling of diesel emissions from dilution tubes is assessed. Rates of formation are calculated using data generated from several independent filter exposure studies. A portion of the 1-NP (12% average) found in participates collected from light-duty (LDD) and heavy-duty diesels (HOD) was found to be due to formation on the filter under average sampling conditions of 10-15/1 dilution at 44°C with 3 ppm NO₂ for 23 min. On the average, the concentration of 1-NP in participates emitted from HDD is 16 times less than that found in LDD run under similiar transient conditions. The average emission rate of 1-NP generated from the LDD and HDD was 4.7 μg/km and 1.5 μg/km, respectively for the vehicles operating under Federal Test Procedure (FTP)-transient conditions. Under operating conditions which increase exhaust temperature (increased speed and load), the concentration of nitro-PAH is significantly reduced with a concurrent increase in the concentration of partially oxidized nitro-PAH and dinitro-PAH. The concentration of 1-NP in the particulates measured from HDD in these dilution tube studies (0.33-0.95 ppm, depending upon engine load) is comparable to that measured in highway tunnel experiments (0.54 ppm average).     

An Evaluation of the Semi-VOST Method for Determining Emissions from Hazardous Waste Incinerators

The Semi-Volatile Organic Sampling Train method was investigated to determine its reliability and to determine the bias and precision of the method when used to determine emissions from hazardous waste incinerators. Experiments showed that the matrix and sampling variables usually involved in sampling emissions from a hazardous waste incinerator had no significant effect on the recovery of 11 different organic compounds. Significant losses of the sampled compounds can occur during sample preparation. The degree of loss appears to be directly related to the compounds, vapor pressure. These losses can be corrected for by adding deuterated surrogates to the sample and analyzing the surrogates along with the native compounds.

The bias determination was based on dynamic spiking of the sampling train with five deuterated organic compounds selected from Appendix VIII of the Resource Conservation and Recovery Act regulations. The results show biases of from -1 ± 8 percent to -18 ± 27 percent for chlorinated and nonchlorinated compounds. Pyridine, a water-soluble compound, showed a larger bias of-29 ± 13 percent. Particular attention to the recovery of water soluble compounds is necessary to minimize bias in their determinations. Further work is needed to determine the reliability of laboratory-determined retention volumes that are used to determine sampling conditions.