重庆大气可吸入颗粒物中多环芳烃的分析测定

本文报告了重庆大气可吸入颗粒物(IP)中多环芳烃(PAH)的分析测定方法和结果.用GC-MS定性和定量分析了重庆IP中的PAH;研究了IP中PAH的种类和分布情况;确认重庆IP中存在甲基多环芳烃(MePAH)、约占33%;颗粒大小分布表明,约有98%PAH存在于小于3μm的颗粒中.     

Toxicity of atrazine and its bioaccumulation and biodegradation in a green microalga,Chlamydomonas mexicana

This study evaluated the toxicity of herbicide atrazine, along with its bioaccumulation and biodegradation in the green microalga Chlamydomonas mexicana. At low concentration (10 μg L^?1), atrazine had no profound effect on the microalga, while higher concentrations (25, 50, and 100 μg L^?1) imposed toxicity, leading to inhibition of cell growth and chlorophyll a accumulation by 22 %, 33 %, and 36 %, and 13 %, 24 %, and 27 %, respectively. Atrazine 96-h EC50 for C. mexicana was estimated to be 33 μg L^?1. Microalga showed a capability to accumulate atrazine in the cell and to biodegrade the cell-accumulated atrazine resulting in 14–36 % atrazine degradation at 10–100 μg L^?1. Increasing atrazine concentration decreased the total fatty acids (from 102 to 75 mg g^?1) and increased the unsaturated fatty acid content in the microalga. Carbohydrate content increased gradually with the increase in atrazine concentration up to 15 %. This study shows that C. mexicana has the capability to degrade atrazine and can be employed for the remediation of atrazine-contaminated streams.     

Estimating and comparing greenhouse gas emissions with their uncertainties using different methods: A case study for an energy supply utility

Energy supply utilities release significant amounts of greenhouse gases (GHGs) into the atmosphere. It is essential to accurately estimate GHG emissions with their uncertainties, for reducing GHG emissions and mitigating climate change. GHG emissions can be calculated by an activity-based method (i.e., fuel consumption) and continuous emission measurement (CEM). In this study, GHG emissions such as CO₂, CH₄, and N₂O are estimated for a heat generation utility, which uses bituminous coal as fuel, by applying both the activity-based method and CEM. CO₂ emissions by the activity-based method are 12–19% less than that by the CEM, while N₂O and CH₄ emissions by the activity-based method are two orders of magnitude and 60% less than those by the CEM, respectively. Comparing GHG emissions (as CO₂ equivalent) from both methods, total GHG emissions by the activity-based methods are 12–27% lower than that by the CEM, as CO₂ and N₂O emissions are lower than those by the CEM. Results from uncertainty estimation show that uncertainties in the GHG emissions by the activity-based methods range from 3.4% to about 20%, from 67% to 900%, and from about 70% to about 200% for CO₂, N₂O, and CH₄, respectively, while uncertainties in the GHG emissions by the CEM range from 4% to 4.5%. For the activity-based methods, an uncertainty in the Intergovernmental Panel on Climate Change (IPCC) default net calorific value (NCV) is the major uncertainty contributor to CO₂ emissions, while an uncertainty in the IPCC default emission factor is the major uncertainty contributor to CH₄ and N₂O emissions. For the CEM, an uncertainty in volumetric flow measurement, especially for the distribution of the volumetric flow rate in a stack, is the major uncertainty contributor to all GHG emissions, while uncertainties in concentration measurements contribute a little to uncertainties in the GHG emissions.

Implications:Energy supply utilities contribute a significant portion of the global greenhouse gas (GHG) emissions. It is important to accurately estimate GHG emissions with their uncertainties for reducing GHG emissions and mitigating climate change. GHG emissions can be estimated by an activity-based method and by continuous emission measurement (CEM), yet little study has been done to calculate GHG emissions with uncertainty analysis. This study estimates GHG emissions and their uncertainties, and also identifies major uncertainty contributors for each method.     

Exposure assessment for methyl and total mercury from seafood consumption in Korea, 2005 to 2008

Reports on the occurrence and intake assessment of mercury for Korean seafood are currently not available. This is the first report to estimate the intake of methyl (Me-Hg) and total mercury (T-Hg) from seafood consumption in Korea. The concentrations of Me-Hg and T-Hg in seafood ranged from 1.02 to 780 (mean: 55.6) ng g(-1) wet weight and 4.89 to 1008 (mean: 100) ng g(-1) wet weight, respectively. The residue levels of Me-Hg and T-Hg in Korean seafood were moderate compared with those found in other countries. The methylation ratios of fish, cephalopods and crustaceans were similar, but shellfish had lower values compared with other species. The intakes of Me-Hg and T-Hg from seafood consumption for the general population were estimated to be 38.8 and 73.8 ng kg(-1) body weight per day, respectively. Mackerel, tuna and squid made the highest contributions to the total intake of these contaminants. Among eight age groups, 30-49 year and 3-6 year age groups had the highest exposure to Me-Hg and T-Hg. The concentrations and intakes of Me-Hg and T-Hg from Korean seafood were less than the allowable residue levels and threshold intake levels suggested by Korean and international authorities. The present study may be useful for risk management of mercury in Korean seafood.     

Supported Pd/Sn bimetallic nanoparticles for reductive dechlorination of aqueous trichloroethylene

A Pd/Sn bimetallic nanoparticles resin (nano-Pd/Sn/resin) was successfully synthesized for reductive transformation of aqueous trichloroethylene (TCE). The physicochemical properties of the prepared resin were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, N(2) isothermal sorption at and X-ray photospectroscopy. The surface-area-normalized rate constants (k(SA)) of Sn particles in the nanoscale range (50-100 nm) were 4.5 times larger than the k(SA) for powdered Sn (0.04 mm). After depositing 1 wt% Pd onto nano-Sn surface, k(SA) was further enhanced by about a factor of 2. Groundwater constituents such as sulfide nitrate and dissolved oxygen had significant negative effects on the rate of TCE degradation by the nano-Pd/Sn/resin. A wet-chemical method regeneration method was observed to effectively restore the reactivity of the poisoned nano-Pd/Sn/resin after dipping in sulfide solution for 2d. In all cases, less than 0.5% of the degraded TCE appeared as chlorinated byproducts including the three dichloroethene isomers. The nano-Pd/Sn/resin technique performs well in transforming TCE into nontoxic hydrocarbons, as compared with other published methods.     

Thermodynamic behavior of rare metals in the melting process of municipal solid waste (MSW) incineration residues

This study aims to identify the thermodynamic behavior of rare metal elements during the melting process of municipal solid waste incineration residues. The fate of several selected rare metal elements was investigated using two approaches: experimental and thermodynamic equilibrium calculation at two actual melting plants. The results revealed that Ag, Bi, Ga, Ge, In, Pd, Sb, Te, and Tl are readily volatilized as chloride and/or gaseous forms and then condensed in melting furnace fly ash. On the other hand, Cr, Ni, Ta, V, and Zr tend to mostly remain in molten slag. Sn is volatilized as SnS (g) under reducing conditions while volatilization is suppressed under oxidizing conditions. Thermodynamically, total volatilization of Mn as MnCl2 (g) occurred with highly available chlorine under oxidizing conditions. However, at the actual plants, only a small proportion was volatilized. As for Co, Mo, and W, no volatilization occurred at the actual plants although the calculations suggest that these elements can form volatile metal chloride and volatilize. Non-equilibrium and heterogeneity of the actual plant melting furnace could explain the discrepancy. This study provided a good qualitative view of the behavior of rare metals in the melting process, but further investigation is required to produce a more accurate simulation and to resolve the discrepancy.     

Nitrogen isotope ratios in pine bark as an indicator of N emissions from anthropogenic sources

The article describes the use of Scots pine bark to identifynitrogen sources in eastern Germany, as well as background areas in Russia and Bulgaria, by using natural isotope ratios of total nitrogen (N_t) and individual N compoundssuch as ammonium (NH₄ ⁺), nitrate (NO₃ ^-)and amid nitrogen (amide-N). The samples collected were analysed using an elemental analyser in connection with a gas isotope mass spectrometer (EA-IRMS). Natural ¹⁵N abundances in pine bark from impact areas suggest that the ammonium accumulated on the surface of the bark is releasedfrom livestock management. Bark of Scots pines growing near agricultural land had highly depleted ¹⁵N_t values (between –8 and –12), while bark from background areas (unpolluted areas) displayed slightly negative ¹⁵N_t values (mean ¹⁵N_t = –3.8). It is assumed that part of the N adsorbed on the bark surface is mainly derived from ammonia(mean ¹⁵N_t = –40.3) escaping from livestock housing and during the application of manure. This assumption is confirmed by experiments under controlled conditions in which manure samples were spread on soil. In addition, temporal and spatial variations of ¹⁵N_t abundances in pine bark from various locations in eastern Germany as wellas pine stands in Nature Park Dübener Heath are discussed.     

Combustion Characteristics of Spent Catalyst and Paper Sludge in an Internally Circulating Fluidized-Bed Combustor

Abstract

Combustion of spent vacuum residue hydrodesulfurization catalyst and incineration of paper sludge were carried out in thermo-gravimetric analyzer and an internally circulating fluidized-bed (ICFB) reactor. From the thermogravimetric analyzer-differential thermo-gravimetric curves, the pre-exponential factors and activation energies are determined at the divided temperature regions, and the thermo-gravimetric analysis patterns can be predicted by the kinetic equations. The effects of bed temperature, gas velocity in the draft tube and annulus, solid circulation rate, and waste feed rate on combustion efficiency of the wastes have been determined in an ICFB from the experiments and the model studies. The ICFB combustor exhibits uniform temperature distribution along the bed height with high combustion efficiency (>90%). The combustion efficiency increases with increasing reaction temperature, gas velocity in the annulus region, and solid circulation rate and decreases with increasing waste feed rate and gas velocity in the draft tube. The simulated data from the kinetic equation and the hydrodynamic models predict the experimental data reasonably well.