Effect of shore position and environmental metal levels on body metal burdens in the barnacle, Elminius modestus

Body (thorax and prosoma) weight, shell growth, and Zn, Cu, Fe, Mn and Ca levels were measured in artificially settled Elminius modestus over a 14-month period following transfer to high, mid and low tide positions in the uncontaminated Menai Strait and two mid tide sites within a Zn and Cu polluted bay on the North West coast of Anglesey. Barnacles showed higher mortality and slower growth at the upper shore position than at any other site. There was no evidence of Zn and Cu regulation by the bodies or shells, and both seemed to reflect environmental levels. Body metal levels were lowest in early winter and the highest second year values were found in January (Zn), March (Cu, Fe) or May (Ca). Higher shore barnacles contained larger concentrations of Zn than mid or low tide animals. Differences in feeding activity and the amount of testes may account for these variations. Reciprocal transplants between polluted and 'clean' sites indicate that body Cu and Zn accumulation and loss was very rapid. Spatial and temporal changes in shell metal levels closely mirror that of the body.     

The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

A Variance Estimator for Constrained Estimates of Change in Relative Categorical Frequencies

Consistent estimators of change and state becomes an issue when sample data come from a mix of permanent and temporary observation units. A joint maximum likelihood estimator of state and change creates estimates of state that depend on antecedent viz. posterior survey results and may differ from estimates of state derived from a single-date analysis of the sample data. A constrained estimator of change in relative categorical frequencies that eliminates this potential inconsistency is proposed and a model based estimator of their sampling variance is developed. The performance of the constrained estimator is quantified against six criteria and a joint maximum likelihood estimator in simulated sampling from 15 populations with three combinations of permanent and temporary samples, four to six categorical class attributes, and constant size between sampling dates. Bias of the constrained estimators was negligible but larger than for joint maximum likelihood estimators. Mean absolute deviations and variances of constrained estimators were generally at par with the joint estimators. Constrained estimators of root mean square errors and achieved coverage of nominal confidence intervals of constrained estimators were occasionally better. A generalized variance function for the constrained estimates of change is provided as a computational shortcut.     

Development of monitoring technology for airborne particulate matter

Particulate matter suspended in the air has adverse effects onhuman health. Its level of concentration is an important parameter in evaluating the degree of hazard it poses to the atmosphere. Conventional methods used in measuring particulatematter are often filter-based, which indicates some disadvantagesbecause such a base requires labor and time. In this study, to achieve real-time measurements, a new electrical method was developed for measuring PM10 and PM2.5 concentrations. The basicprinciple is to electrically charge particles passing through thePM inlet using a corona charger and measure the currents createdby charged particles to obtain the number concentration of particulate matter. A new type inlet based on the particle cupimpactor configuration was designed and its performance was evaluated. A unipolar diffusion charger was developed and thecharger's efficiency was determined experimentally in terms ofPn, which represents the penetration through the charger,P, times the average charge number acquired by a particle,n, for different particle sizes. The correlation was constructed between the PM10 (or the PM2.5) mass concentrationsand the electrical currents due to particles, which were chargedby the diffusion charger.     

Recycling of petroleum-contaminated sand

The environmental impact of using petroleum-contaminated sand (PCS) as a substitute in asphalt paving mixtures was examined. An appreciable component of PCS is oily sludge, which is found as the dregs in oil storage tanks and is also produced as a result of oil spills on clean sand. The current method for the disposal of oily sludge is land farming. However, this method has not been successful as an oil content of < 1% w/w is required, and difficulty was encountered in reaching this target. The reuse of the sludge in asphalt paving mixtures was therefore considered as an alternative. Standard tests and environmental studies were conducted to establish the integrity of the materials containing the recycled sludge. These included physical and chemical characterization of the sludge itself, and an assessment of the mechanical properties of materials containing 0%, 5%, 22% and 50% oily sludge. The blended mixtures were subjected to special tests, such as Marshall testing and the determination of stability and flow properties. The experimental results indicated that mixtures containing up to 22% oily sludge could meet the necessary criteria for a specific asphalt concrete wearing course or bituminous base course. To maximize the assay from the recycled material, the environmental assessment was restricted to the 50% oily sludge mixture. Leachates associated with this particular mixture were assayed for total organic residue and certain hazardous metal contaminants. The results revealed that the organics were negligible, and the concentrations of the metals were not significant. Thus, no adverse environmental impact should be anticipated from the use of the recycled product. Our research showed that the disposal of oily sludge in asphalt paving mixtures could possibly yield considerable savings per tonne of asphalt concrete, and concurrently minimize any direct impact on the environment.     

Chlorinated Hydrocarbons in Livers of American Mink (Mustela vison) and River Otter (Lutra canadensis) from the Columbia and Fraser River Basins, 1990–1992

We investigated chlorinated hydrocarbon contaminants in aquatic mustelid species on the Fraser and Columbia Rivers of northwestern North America. Carcasses of river otter (Lutra canadensis) (N=24) and mink (Mustela vison) (N=34) were obtained from commercial trappers during the winters of 1990–91 and 1991–92. Pooled liver samples were analyzed for organochlorine pesticides, polychlorinated biphenyls (PCBs), including non-ortho congeners, polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Most samples contained detectable concentrations of DDE, PCBs, although there was substantial variability in patterns and trends among neighboring samples. Concentrations of DDE were in some mink and several otter samples from the lower Columbia River elevated (to 4700 g/kg wet weight); excluding one mink sample from the Wenatchee area, mean DDE levels generally decreased between 1978–79 and 1990–92. PCBs were present in all samples. PCB concentrations in otter livers collected from the lower Columbia were ten-fold lower than measured a decade previously; nevertheless, a sample taken near Portland had a mean concentration of 1500 g/kg, within a range of concentrations associated with reproductive effects in captive mink. Concentrations of 2,3,7,8-TCDD and TCDF were generally below detection limits, except for one otter collected near a pulp mill at Castlegar, on the upper Columbia, with 11 ng TCDD/kg in liver. Elevated concentrations of higher chlorinated PCDD/Fs, probably resulting from use of chlorophenolic wood preservatives, were found in both species; one otter sample from the lower Columbia had 2200 ng OCDD/kg. International TCDD toxic equivalent levels in mink (31 ng/kg) and otter (93 ng/kg) from the lower Columbia River approached toxicity thresholds for effects on reproduction in ranch mink.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.     

Follow-up to environmental impact assessment: Learning from the Canadian Government experience

The environmental impact assessment procedure for Canadian federal government projects is briefly described. In the non-legislated Canadian system, follow-up to assessments is one of the major means of encouraging and improving the implementation of environmental impact assessment and the quality of environmental work done around development projects. The results of a study on the status of follow-up in the Canadian Government are presented. Factors that limit and that are conducive to follow-up are discussed. The effectiveness of follow-up depends as much on the circumstances surrounding a project and the concerned parties as on the follow-up techniques used; both of these aspects can be addressed in the planning and management of follow-up and of environmental impact assessment overall. Areas for improving the management of follow-up are identified and discussed: planning of follow-up activities, coordination of concerned parties, generation of clear understandings, information management, resource allocation, and maintenance of credibility. A method for planning follow-up activities for specific projects is presented.     

Soil sampling and analysis for volatile organic compounds

Concerns over data quality have raised many questions related to sampling soils for volatile organic compounds (VOCs). This paper was prepared in response to some of these questions and concerns expressed by Remedial Project Managers (RPMs) and On-Scene Coordinators (OSCs). The following questions are frequently asked:

1. Is there a specific device suggested for sampling soils for VOCs?
2. Are there significant losses of VOCs when transferring a soil sample from a sampling device (e.g., split spoon) into the sample container?
3. What is the best method for getting the sample from the split spoon (or other device) into the sample container?
4. Are there smaller devices such as subcore samplers available for collecting aliquots from the larger core and efficiently transferring the sample into the sample container?
5. Are certain containers better than others for shipping and storing soil samples for VOC analysis?
6. Are there any reliable preservation procedures for reducing VOC losses from soil samples and for extending holding times?

Guidance is provided for selecting the most effective sampling device for collecting samples from soil matrices. The techniques for sample collection, sample handling, containerizing, shipment, and storage described in this paper reduce VOC losses and generally provide more representative samples for volatile organic analyses (VOA) than techniques in current use. For a discussion on the proper use of sampling equipment the reader should refer to other sources (Acker, 1974; U.S. EPA, 1983; U.S. EPA, 1986a). Soil, as referred to in this report, encompasses the mass (surface and subsurface) of unconsolidated mantle of weathered rock and loose material lying above solid rock. Further, a distinction must be made as to what fraction of the unconsolidated material is soil and what fraction is not. The soil component here is defined as all mineral and naturally occurring organic material that is 2 mm or less in size. This is the size normally used to differentiate between soils (consisting of sands, silts, and clays) and gravels. Although numerous sampling situations may be encountered, this paper focuses on three broad categories of sites that might be sampled for VOCs:

1. Open test pit or trench.
2. Surface soils (<5 ft in depth).
3. Subsurface soils (>5 ft in depth).

     

Woodstove emission measurement methods: Comparison and emission factors update

On February 26, 1988, the U.S. Environmental Protection Agency promulgated Standards of Performance for residential wood heaters, or woodstoves. Over the past several years, a number of field studies have been undertaken to determine the actual level of emission reduction achieved by new technology woodstoves in everyday use. These studies have required the development and use of particulate and gaseous emission sampling equipment compatible with operation in private houses. Since woodstoves are tested for certification in the laboratory using EPA Methods 5G and 5H, it is of substantial interest to determine the correlation between these regulatory methods and the in-house equipment. Two in-house sampling systems have been used most widely. One is an intermittent, pump-driven particulate sampler which collects particulate and condensable organics on a filter and organic adsorbent resin. Oxygen concentration is measured by a sensor in the sample line. The sampler is controlled by a data logger which also records other parameters of interest. The second system uses an evacuated cylinder as the motive force. Particulate and condensable organics are collected in a condenser and dual filter. The sampler operates continuously whenever the stack temperature is above the set point. Average stack gas concentrations are measured from the evacuated cylinder at the conclusion of the sampling period. Both samplers were designed to operate unattended for 1-week periods. A large number of tests have been run comparing Methods 5G and 5H to both of the field samplers. This paper presents these comparison data and determines the relationships between laboratory certification sampling methods and field samplers.