Optimal and suboptimal control of anaerobic digesters

Anaerobic digester failure due to entry of inhibitors or sudden changes in the feed substrate concentration may be encompassed beneficially by applying optimal control theory. An almost proportional relationship between the dilution rate and the methane production rate leads to a simple suboptimal control law with only minor loss in performance, after the occurrence of the above mentioned events.     

Classification of local- and landscape-scale ecological types in the southern Appalachian Mountains

Five local ecological types based on vegetative communities and two landscape types based on groups of communities, were identified by integrating landform, soil, and vegetation components using multivariate techniques. Elevation and several topographic and soil variables were highly correlated with types of both scales. Landscape ecological types based only on landform and soil variables without vegetation did not correspond with types developed using vegetation. Models developed from these relationships could allow classification and mapping of extensive areas using geographic information systems.     

Reduction of SO2 emissions by ammonia gas during unstaged combustion

The reduction of SO₂ by the addition of ammonia gas has been studied in a 2 m high fluidized bed combustor having a 30 cm static bed height and a freeboard height of 170 cm. Ammonia gas was injected at 52 cm above the distributor where the temperature is ca. 700° C by an uncooled stainless steel tube injector. Experiments were carried out to investigate the effects of amminia gas injection on sulphur dioxide emissions at unstaged conditions of: (i) excess air level, (ii) NH₃:SO₂ molar ratio, (iii) fluidizing velocity and (iv) bed height.A maximum reduction of 75% in SO₂ emissions was found at 40% excess air, at an NH₃:SO₂ molar ratio of 5.4. The onset of SO₂ reduction occurred at an NH₃:SO₂ ratio of 1.5 However, the most effective ratio was found to be between 3 and 5. Fluidizing velocity and bed height were also found to have significant influence on SO₂ reduction.It is difficult to determine how the SO₂ reduction varied with operating conditions. When ammonia is added in the main combustor zone, the temperature is much higher than that required for the occurrence of sulphur dioxide-ammonia and sulphur trioxide-ammonia reactions. However, this paper points out the significance of ammonia addition in the reduction of sulphur dioxide.     

Pesticide burden on some insects of economic importance in Lucknow (India)

Some insects of economic importance from Lucknow (India) have been investigated for their pesticide burden. Chlorinated pesticide residues of DDT, BHC and aldrin along with their metabolites and isomers have been detected in crop pollinating insects, honeybees (Apis indica) and butterflies (Danais chrysippus and Eurema sp.) and predators, dragonfly (Platythemis sp.) and wasps (Polistes herebreus). DDT and their metabolites were present in concentrations which varied from 231–796 ng g^–1, followed by BHC (10–60 ng g^–1), and aldrin (0.26–6.68 ng g^–1). This finding is likely to stimulate newer interest in the area of pesticide research and start meaningful investigation to find if bioaccumulated pesticides would have adverse impact on otherwise beneficial potentials of such insects in our ecosystems.     

Environmental and biological monitoring of methyl ethyl ketone (MEK)

This study was conducted to evaluate the usefulness of various biological parameters for monitoring of workers exposed to methyl ethyl ketone (MEK). Fifty male workers from a large magnetic videotape factory participated in this study. Personal air samples were collected using 3M organic vapor monitors and analysed for MEK by gas chromatography with flame ionisation detector (FID). 10 mL of urine; blood (1 mL) and exhaled air were also collected at the end of an 8-hour workshift. The headspace GC method was applied for measurement of urinary and blood MEK. MEK in expired air was analysed directly by using a GC/FID.The correlation coefficients (r) between environmental MEK and all other biological parameters measured show significant positive relationships. The r for environmental MEK and urine MEK was 0.84; for blood 0.73 and for breath 0.64. The correlation coefficients between blood and urine was 0.72; blood and breath was 0.88 and urine and breath 0.60. These findings suggest that measurements of unmetabolised MEK in blood, exhaled air and urine can be used for biological monitoring of MEK exposure. Nevertheless, laboratory methodological assessment is in favour of measuring urinary MEK as it is non-invasive and does not have to be analysed immediately after collection.     

Spectrophotometric determination of ferbam (iron(III) dimethyldithiocarbamate) in commercial sample and wheat grains using 4,7-diphenyl-1,10-phenanthroline after extraction into mesityl oxide

A procedure has been developed for the determination of iron(III) dimethyldithiocarbamate by converting it into iron(II)-bathophenanthroline complex, which is then extracted into mesityl oxide in the presence of potassium perchlorate. The absorbance is then measured at 534 nm against a reagent blank. Beer's law is obeyed over the concentration range 0.5-20 microg ml(-1) in the final solution. The method is sensitive, highly selective and can be used for the determination of ferbam in a commercial sample, and in mixtures with various dithiocarbamates (ziram, zineb, maneb, etc.) and in wheat grains.     

The influence of geometry and draught shields on the performance of passive samplers

Passive samplers provide an excellent opportunity to perform indicative measurements or establish a dense network of measuring sites. A drawback compared with conventional active measuring methods is the larger spread of results. This variation can, to a large extent, be attributed to the influence of temperature, sampler geometry and wind on sampling results. A proper design of sampler geometry and optimum choice of draught shield can reduce the influence of wind velocity on a badge type sampler to less than 10%. Wire mesh screens prove to be inadequate in damping turbulence. Filters give good results. Attention should be paid to the size and isolation value of the walls of the sampler to prevent thermal updrafts occurring within the sampler. Tube type samplers are less influenced by wind, provided that turbulence is prevented from influencing diffusion within the sampler.     

Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.     

Organophosphate flame retardants and plasticisers in wastewater treatment plants

Previous studies have revealed that chlorinated and non-chlorinated organophosphorous flame retardants and plasticisers are important contaminants in German surface waters and it has been demonstrated that wastewater treatment plants contribute to the emission of these substances. In this study temporal development as well as elimination efficiency were determined in two wastewater treatment plants (STP) in the Ruhr/Rhine area at different stages of the wastewater treatment process. The samples were analysed for the non-chlorinated organophosphate esters tri-n-butylphosphate (TnBP), tri-iso-butylphosphate (TiBP), tris-(butoxyethyl)-phosphate (TBEP) and triphenylphosphate (TPP) and the chlorinated organophosphate esters tris-(2-chloro, 1-methylethyl)-phosphate (TCPP), tris-(2-chloro-, 1-chloromethylethyl)-phosphate (TDCP) and tris-(2-chloroethyl)-phosphate (TCEP). The study showed that there were significant differences in the elimination of chlorinated and non-chlorinated organophosphorous flame retardants. The elimination rates ranged from 57-86% for TiBP, TnBP and TBEP at both STP's. No elimination of the chlorinated flame retardants TCPP, TDCP and TCEP was observed in any of the sampled STPs. At both STPs the first treatment steps and the final filtration did not contribute to the elimination of the non-chlorinated organophosphorous flame retardants while the aeration step did. At both STPs the efficiency of the cleaning process concerning the flame retardants was comparable. Thus the type of construction of the STP was not relevant for the elimination of these substances. Additionally a strong day-to-day variation was observed, while in one STP a temporal trend for TCPP during the week was found.     

Selection and Calibration of Numerical Modeling in Flow and Water Quality

Numerical modeling is frequently used in coastal engineering research and application. One possible issue associated with using this method however, is that initial outcomes might differ from expectation. Modeling manipulation addresses this issue by changing the initial parameters which in turn affects the final output results. The advancement of modeling techniques in recent years has seen a gradual but steady accruement of knowledge regarding the relationship between input parameters and possible outputs, which has resulted in improved accuracy and efficiency methods. The advancements within this field have predominantly occurred on an individual basis and as such lack standardisation. An expert numerical modeler may use this knowledge subconsciously, yet may not know how to convey it to the model users. This paper has been written to introduce a systematic intelligent coding schema designed to organise current coastal engineering modeling manipulation knowledge into a standardised format. This system is relevant to the development of appropriate strategies for improved accuracy and efficiency as well as model modification to simulate specific real phenomena in prototype application cases.