Particulate,Carbon Monoxide,and Acid Emission Factors for Residential Wood Burning Stoves

Emissions from residential wood burning stoves are of Increasing concern in many areas. This concern is due to the magnitude of the emissions and the toxic and chemical characteristics of the pollutants. Recent testing of standard and new technology woodstoves has provided data for developing a family of particulate and carbon monoxide emission factor curves. This testing has also provided data illustrating the acidity of woodstove emissions. The particulate and carbon monoxide curves relate the actual stove emissions to the stove size and operating parameters of burn rate, fuel loading, and fuel moisture. Curves relating stove types to the acidity of emissions have also been constructed.

Test data show actual emissions vary from 3 to 50 grams per kilogram for particles and from 50 to 300 grams per kilogram for carbon monoxide. Since woodstove emissions are the largest single category of particulate emissions in many areas, it Is essential that these emissions be quantified specifically for geographic regions, allowing meaningful impact analysis modeling to be accomplished. Emission factors for particles and carbon monoxide are presented from several stove sizes and burn rates.

The acidic nature of woodstove emissions has been clearly demonstrated. Tests indicate woodstove flue gas condensate solutions to be predominantly in the 2.8 to 4.2 pH range. Condensate solutions from conventional woodstoves exhibited the characteristic buffering capacity of carboxylic acids when titrations were performed with a strong base. The environmental impact of buffered acidic woodstove emissions is not currently well understood; however, it is possible with the data presented here to make semi-quantitative estimates of acid emissions from particulate and carbon monoxide emission factors and wood use inventories.     

Eliminating Reheat from Existing FGD Systems

The Clean Air Act Amendments of the early 1970_s required coal burning utilities to reduce their emissions of sulfur dioxide. Lime or limestone based wet systems were employed for flue gas desulfurization (FGD). These systems reduced flue gas temperatures to below acid dew point conditions. Concerned about the prospect of ductwork exposed to a saturated, acid-rich environment, most utilities turned to stack gas reheat (SGR) to increase flue gas temperatures. By 1980, 82 percent of all FGD facilities employed SGR. Today there are about 130 FGD systems of which 101 employ some form of stack gas reheat.     

The Effects of Infiltration and Insulation on the Source Strengths and Indoor Air Pollution from Combustion Space Heating Appliances

Many energy conservation strategies for residences involve reducing house air exchange rates. Reducing the air exchange rate of a house can cause an increase in pollutant levels if there is an indoor pollution source and if the indoor pollutant source strength remains constant. However, if the indoor pollutant source strength can also be reduced, then it is possible to maintain or even improve indoor air quality. Increasing the insulation level of a house is a means of achieving energy conservation goals and, in addition, can reduce the need for space heating and thereby reduce the pollutant source strengths of combustion space heaters such as unvented kerosene space heaters, unvented gas space heaters, and wood stoves. In this paper, the indoor air quality trade-off between reduced infiltration and increased insulation in residences is investigated for combustion space heaters. Two similar residences were used for the experiment. One residence was used as a control and the other residence had infiltration and insulation levels modified. An unvented propane space heater was used as the source in this study. A model was developed to describe the dependence of both indoor air pollution levels and the appliance source strengths on house air exchange rates and house insulation levels. Model parameters were estimated by applying regression techniques to the data. Results show that indoor air pollution levels in houses with indoor combustion space heating pollution sources can be held constant (or lowered) by reducing the thermal conductance by an amount proportional to (or greater than) the reduction of the air exchange rate.     

Patterns and Concentrations of PM10 in a Mountainous Basin Region

ABSTRACT

In this study, continuous data of PM₁₀ (particles with aerodynamic diameter <10 u,m) concentration measurements for a 4-yr period were analyzed. These measurements have been carried out in the Eordea Basin, an industrial area in the northwestern mountainous region of Greece. The annual, monthly, and diurnal patterns are presented and investigated regarding the prevailing meteorological conditions and atmospheric processes that affect the ambient concentrations of PM₁₀. The effect of wind on controlling PM₁₀ concentration is also discussed. Based on the data analysis, an attempt is made to provide useful information about air quality levels, taking into account U.S. Environmental Protection Agency air quality standards.     

Black Carbon Aerosol at McMurdo Station,Antarctica

ABSTRACT

Aerosol light absorption as black carbon (BC) was measured from November 19, 1995, to February 6, 1996, at a location 0.65 km downwind of the center of McMurdo Station on the Antarctic coast. The results show a bimo-dal frequency distribution of BC concentrations. Approximately 65% of the measurements were found in a mode at a low range of concentrations centered at ~20 ng/m³. These concentrations are higher than those found at other remote Antarctic locations and probably represent contamination from the station. The remaining measurements were in a high-concentration mode (BC ~300 ng/m³), indicating direct impact of local emissions from combustion activities at the station. High values of BC were associated with winds from the direction of the station, and the BC flux showed a clear directionality. Maximum BC concentrations occurred between 7:00 and 11:00 a.m. The "polluted" mode accounted for more than 80% of the BC frequency-weighted impact at this location.     

Spatial Differences in Outdoor PM10 Mass and Aerosol Composition in Mexico City

Abstract

Twenty-five MiniVol samplers were operated throughout the Mexico City metropolitan region from February 22 through March 22, 1997, to evaluate the variability of PM₁₀ concentrations and composition. The highest PM₁₀ concentrations were found in neighborhoods with unpaved or dirty roads, and elements related to crustal material were the main cause of differences from nearby (<200 m) monitors that were not adjacent to the roadbed. SO₄ ^2?concentrations were homogeneous across the city. SO₄ ^2?measured at the city boundaries was about two-thirds of the concentrations measured within the urbanized area, indicating that most SO₄ ^2? is of regional origin. Elemental carbon (EC) and organic carbon (OC) concentrations were highly variable, with higher concentrations in areas that had high diesel traffic and older vehicles. Spatial correlations among PM₁₀ concentrations were high, even though absolute concentrations were variable, indicating a common effect of meteorology on the concentration or dispersion of local emissions.     

Effect of americium-241 on luminous bacteria. Role of peroxides

The effect of americium-241 (²⁴¹Am), an alpha-emitting radionuclide of high specific activity, on luminous bacteria Photobacterium phosphoreum was studied. Traces of ²⁴¹Am in nutrient media (0.16-6.67 kBq/L) suppressed the growth of bacteria, but enhanced luminescence intensity and quantum yield at room temperature. Lower temperature (4 °C) increased the time of bacterial luminescence and revealed a stage of bioluminescence inhibition after 150 h of bioluminescence registration start. The role of conditions of exposure the bacterial cells to the ²⁴¹Am is discussed. The effect of ²⁴¹Am on luminous bacteria was attributed to peroxide compounds generated in water solutions as secondary products of radioactive decay. Increase of peroxide concentration in ²⁴¹Am solutions was demonstrated; and the similarity of ²⁴¹Am and hydrogen peroxide effects on bacterial luminescence was revealed. The study provides a scientific basis for elaboration of bioluminescence-based assay to monitor radiotoxicity of alpha-emitting radionuclides in aquatic solutions.