Isometric Pull and Push Strengths of Paraplegics in the Workspace: 2. Statistical Analysis of Spatial Factors

The effect of reach levels, horizontal angles, and vertical angles on isometric pull and push strengths of male and female was determined. Highly significant increases in men’s push strength were found between extreme to maximum reaches, and from extreme to normal reaches. However, for women’s push strength, a significant increase was found only between extreme to maximum reach. Significant or highly significant increases were found in men’s and women’s pull strength between the horizontal angle (θ) sagittal through the active shoulder (90°) and other angles (0, 45, and 135°). However, for men’s push strength, highly significant increases were found between the horizontal angle 45° from the frontal plane, and other angles. For women’s push strength, significant or highly significant increases were found between the horizontal angles 0° and angles of 90 and 135°. For men’s and women’s pull strength, significant or highly significant increases were found between the vertical angle (?), 90°, and other angles (–20, 0, and 45°). Similar increases were found for women’s push strength between the 45° angle and other angles. In the design of a workstation for paraplegics that requires pull and push forces, consideration must be given to the spatial factors.     

Experimental investigation of spark ignition energy in kerosene,hexane, and hydrogen

Quantifying the risk of accidental ignition of flammable mixtures is extremely important in industry and aviation safety. The concept of a minimum ignition energy (MIE), obtained using a capacitive spark discharge ignition source, has traditionally formed the basis for determining the hazard posed by fuels. While extensive tabulations of historical MIE data exist, there has been little work done on ignition of realistic industrial and aviation fuels, such as gasoline or kerosene. In the current work, spark ignition tests are performed in a gaseous kerosene–air mixture with a liquid fuel temperature of 60 °C and a fixed spark gap of 3.3 mm. The required ignition energy was examined, and a range of spark energies over which there is a probability of ignition is identified and compared with previous test results in Jet A (aviation kerosene). The kerosene results are also compared with ignition test results obtained in previous work for traditional hydrogen-based surrogate mixtures used in safety testing as well as two hexane–air mixtures. Additionally, the statistical nature of spark ignition is discussed.     

An approach for domino effect reduction based on optimal layouts

An approach to reduce the probability of producing a domino effect in process industry is developed in this work. It is assumed that optimal layouts should include appropriate analysis to reduce risk during the process design stage. The model developed for this approach combines the estimation of probability of damage due to overpressure, proposed by Mingguang and Juncheng (2008), and escalation threshold values defined by Cozzani, Gubinelli, and Salzano (2006). These equations are combined with other typical layout constraints as well as bounding the probability constraint, which has resulted in a highly non-linear MINLP problem. Solving a case study used by other authors provides evidence for reliability of the developed approach. In this way, layouts are designed to reduce the escalation probability yielding safe distributions.     

Small-scale physical explosions in shock tubes in comparison with condensed high explosive detonations

A series of small-scale experiments involving physical explosions in a 1.6 l pressure vessel was carried out. Explosions were initiated by spontaneous rupture of an aluminium membrane on one side of the vessel at a pressure in the range 1–1.2 MPa. The pressure waves released were measured at different distances along two separate shock tubes, one 10 m long and 200 mm in diameter (closed at one end by the high pressure vessel) and the other 15 m long and 100 mm in diameter.TNT equivalency was used for predicting the blast wave characteristics after vessel rupture. TNT equivalency was used because equations for prediction of peak pressure and impulse of the blast wave in 1-D geometry after detonations of condensed explosives are known. Some experiments with an equivalent amount of real explosive were carried out for comparison with the theoretical and experimental data obtained. The applicability of the TNT equivalency method presented for calculations of maximum pressure and shock wave impulse generated after rupture of the pressure vessel in 1-D geometry is discussed.     

Media surface properties and the development of nitrifying biofilms in mixed cultures for wastewater treatment

Plastic was tested to select biofilm support media that would enhance nitrification in the presence of heterotrophs. Eight different types (acrylonitrile butadiene styrene, nylon, polycarbonate, polyethylene, polypropylene, polytetrafluoroethylene (PTFE), polyvinyl chloride and tufnol) were immersed in an aerobic fed-batch reactor receiving domestic settled wastewater. Nitrification rates did not correlate with biomass concentrations, nor surface roughness of the plastics as measured by atomic force microscopy (AFM). The maximum nitrification rate of 1.5 g/m² d^?1 was obtained from biofilms growing on PTFE which had the lowest surface adhesion force (8 nN). Nitrification rates for the biofilms were inversely correlated with the attraction forces as measured by AFM.     

Environmental risk mapping of accidental pollution and its zonal prevention in a city

Accidental releases of pollution can have severe environmental, societal, economic, and institutional consequences. This paper considers the use of risk mapping of accidental pollution events, and zonal prevention measures for alleviating the impact on large urban areas. An Environmental Pollution Accident Risk Mapping (EPARM) model is constructed according to a mapping index system supported by quantitative sub-models dedicated to evaluating the risk arising from different sources of potential accidental pollution. The EPARM approach consists of identifying suitable indexes, assessment of environmental risk at regional and national scales based on information on previous pollution accidents and the prevailing environmental and social conditions, and use of GIS to map the overall risk. A case study of pollution accidents in Minghang District, Shanghai, China is used to demonstrate the effectiveness of the model. The paper also proposes a systemic framework for accidental environmental pollution risk prevention, and detailed countermeasures for specific risk zones.     

Experimental and theoretical investigations for mitigating NaAlH4 reactivity risks during postulated accident scenarios involving exposure to air or water

Experimental and theoretical studies were conducted to investigate the pyrophoricity and water-reactivity risks associated with employing sodium alanate (NaAlH₄) complex metal hydride in on-board vehicular hydrogen (H₂) storage systems. The ignition and explosivity of NaAlH₄ upon exposure to oxidizers in air or water were attributed to the spontaneous formation of stable hydroperoxyl intermediates on the NaAlH₄ surface and/or H₂ production, as well as the large driving force for NaAlH₄ conversion to favorable hydroxide products predicted by atomic and thermodynamic modeling. The major products from NaAlH₄ exposure to air: NaAl(OH)₄, gibbsite and bayerite Al(OH)₃, and Na₂CO₃ observed by XRD, were identified to be formed by surface-controlled reactions. The reactivity risks were significantly minimized, without compromising de-/re-hydrogenation cyclability, by compacting NaAlH₄ powder into wafers to reduce the available surface area. These core findings are of significance to risk mitigation and H₂ safety code and standard development for the safe use of NaAlH₄ for on-board H₂ storage in light-duty vehicles.     

Survey of polycyclic aromatic hydrocarbons (PAHs) in arterial street air of Hangzhou

ＩｎｔｒｏｄｕｃｔｉｏｎＰｏｌｙｃｙｃｌｉｃａｒｏｍａｔｉｃｈｙｄｒｏｃａｒｂｏｎｓ (ＰＡＨｓ)ａｒｅｗｉｄｅｓｐｒｅａｄｅｎｖｉｒｏｎｍｅｎｔａｌｐｏｌｌｕｔａｎｔｓｉｎｔｈｅａｔｍｏｓｐｈｅｒｅ.Ｔｈｅｙａｒｅｇｅｎｅｒａｔｅｄｉｎｔｈｅｃｏｍｂｕｓｔｉｏｎ .Ｔｈｅｍａｊｏｒｓｏｕｒｃｅｓｉｄｅｎｔｉｆｉｅｄｉｎｃｌｕｄｅｆｏｓｓｉｌｆｕｅｌｓ,ｖｅｈｉｃｕｌａｒｔｒａｆｆｉｃ,ｉｎｄｕｓｔｒｉａｌｐｒｏｃｅｓｓｅｓ,ｓｍｏｋｉｎｇａｎｄｄｏｍｅｓｔｉｃｈｅａｔｉｎｇ (Ｐｅｌｔｏｎｅｎ ,1995) .Ｔ…     

磷石膏水热法合成硫酸钙晶须

以磷石膏为原料,二水合硫酸钙、硫酸镁、甘油为添加剂,采用水热法合成硫酸钙晶须,考察了料浆含量、反应温度、反应时间、体系pH等因素对晶须的直径和长径比的影响;并采用SEM技术观察硫酸钙晶须的形貌。实验结果表明,当磷石膏含量2.5%（w）、反应温度130 ℃、反应时间4 h、体系pH 4时,制备得到的硫酸钙晶须长径比为56.24,平均直径为0.17 μm。SEM表征结果显示,硫酸钙晶须形貌规整、分散均匀、直径较小,达百纳米级。