Challenges in quantifying biosphere-atmosphere exchange of nitrogen species

Recent research in nitrogen exchange with the atmosphere has separated research communities according to N form. The integrated perspective needed to quantify the net effect of N on greenhouse-gas balance is being addressed by the NitroEurope Integrated Project (NEU). Recent advances have depended on improved methodologies, while ongoing challenges include gas-aerosol interactions, organic nitrogen and N(2) fluxes. The NEU strategy applies a 3-tier Flux Network together with a Manipulation Network of global-change experiments, linked by common protocols to facilitate model application. Substantial progress has been made in modelling N fluxes, especially for N(2)O, NO and bi-directional NH(3) exchange. Landscape analysis represents an emerging challenge to address the spatial interactions between farms, fields, ecosystems, catchments and air dispersion/deposition. European up-scaling of N fluxes is highly uncertain and a key priority is for better data on agricultural practices. Finally, attention is needed to develop N flux verification procedures to assess compliance with international protocols.     

Leaching of seven pesticides currently used in cotton crop in Mato Grosso State-Brazil

This study aimed to evaluate the leaching of pesticides and the applicability of the Attenuation Factor (AF) Model to predict their leaching. The leaching of carbofuran, carbendazim, diuron, metolachlor, alpha and beta endosulfan and chlorpyrifos was studied in an Oxisol using a field experiment lysimeter located in Dom Aquino-Mato Grosso. The samples of percolated water were collected by rain event and analyzed. Chemical and physical soil attributes were determined before pesticide application to the plots. The results showed that carbofuran was the pesticide that presented a higher leaching rate in the studied soil, so was the one representing the highest contamination potential. From the total carbofuran applied in the soil surface, around 6% leached below 50 cm. The other pesticides showed lower mobility in the studied soil. The calculated values to AF were 7.06E-12 (carbendazim), 5.08E-03 (carbofuran), 3.12E-17 (diuron), 6.66E-345 (alpha-endosulfan), 1.47E-162 (beta-endosulfan), 1.50E-06 (metolachlor), 3.51E-155 (chlorpyrifos). AF Model was useful to classify the pesticides' potential for contamination; however, that model underestimated pesticide leaching.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

Acetylcholinesterase-polyaniline biosensor investigation of organophosphate pesticides in selected organic solvents

The behavior of an amperometric organic-phase biosensor consisting of a gold electrode modified first with a mercaptobenzothiazole self-assembled monolayer, followed by electropolymerization of polyaniline in which acetylcholinesterase as enzyme was immobilized, has been developed and evaluated for organophosphorous pesticide detection. The voltammetric results have shown that the formal potential shifts anodically as the Au/MBT/PANI/AChE/PVAc thick-film biosensor responded to acetylthiocholine substrate addition under anaerobic conditions in selected organic solvent media containing 2% v/v 0.05 M phosphate buffer, 0.1 M KCl (pH 7.2) solution. Detection limits in the order of 0.147 ppb for diazinon and 0.172 ppb for fenthion in acetone-saline phosphate buffer solution, and 0.180 ppb for diazinon and 0.194 ppb for fenthion in ethanol-saline phosphate buffer solution has been achieved.     

Use of n-fold cross-validation to evaluate three methods to calculate heavy truck annual average daily traffic and vehicle miles traveled

Reliable estimates of heavy-truck volumes in the United States are important in a number of transportation applications including pavement design and management, traffic safety, and traffic operations. Additionally, because heavy vehicles emit pollutants at much higher rates than passenger vehicles, reliable volume estimates are critical to computing accurate inventories of on-road emissions. Accurate baseline inventories are also necessary to forecast future scenarios. The research presented in this paper evaluated three different methods commonly used by transportation agencies to estimate annual average daily traffic (AADT), which is used to determine vehicle miles traveled (VMT). Traffic data from continuous count stations provided by the Iowa Department of Transportation were used to estimate AADT for single-unit and multiunit trucks for rural freeways and rural primary highways using the three methods. The first method developed general expansion factors, which apply to all vehicles. AADT, representing all vehicles, was estimated for short-term counts and was multiplied by statewide average truck volumes for the corresponding roadway type to obtain AADT for each truck category. The second method also developed general expansion factors and AADT estimates. Truck AADT for the second method was calculated by multiplying the general AADT by truck volumes from the short-term counts. The third method developed expansion factors specific to each truck group. AADT estimates for each truck group were estimated from short-term counts using corresponding expansion factors. Accuracy of the three methods was determined by comparing actual AADT from count station data to estimates from the three methods. Accuracy of the three methods was compared using n-fold cross-validation. Mean squared error of prediction was used to estimate the difference between estimated and actual AADT. Prediction error was lowest for the method that developed separate expansion factors for trucks. Implications for emissions estimation using the different methods are also discussed.     

Source apportionment of fine particles in Tennessee using a source-oriented model

Source apportionment of fine particles (PM2.5, particulate matter < 2 microm in aerodynamic diameter) is important to identify the source categories that are responsible for the concentrations observed at a particular receptor. Although receptor models have been used to do source apportionment, they do not fully take into account the chemical reactions (including photochemical reactions) involved in the formation of secondary fine particles. Secondary fine particles are formed from photochemical and other reactions involving precursor gases, such as sulfur dioxide, oxides of nitrogen, ammonia, and volatile organic compounds. This paper presents the results of modeling work aimed at developing a source apportionment of primary and secondary PM2.5. On-road mobile source and point source inventories for the state of Tennessee were estimated and compiled. The national emissions inventory for the year 1999 was used for the other states. U.S. Environmental Protection Agency Models3/Community Multi-Scale Air Quality modeling system was used for the photochemical/secondary particulate matter modeling. The modeling domain consisted of a nested 36-12-4-km domain. The 4-km domain covered the entire state of Tennessee. The episode chosen for the modeling runs was August 29 to September 9, 1999. This paper presents the approach used and the results from the modeling and attempts to quantify the contribution of major source categories, such as the on-road mobile sources (including the fugitive dust component) and coal-fired power plants, to observed PM2.5 concentrations in Tennessee. The results of this work will be helpful in policy issues targeted at designing control strategies to meet the PM2.5 National Ambient Air Quality Standards in Tennessee.     

Numerical simulation of hydrogen–air detonation for damage assessment in realistic accident scenarios

An accidental hydrogen release within an equipment enclosure may result in the presence of detonable mixture in a confined environment. From a safety standpoint, it is then useful to assess the potential for damage. In that context, numerical simulation of the sequence of events subsequent to detonative ignition provides a useful tool, although with obvious limitations. This article describes the procedure, summarizes two case studies, and reviews the limitations. First, a hydrogen dispersion pattern is obtained from numerical simulation of dispersion, using a commercial package designed primarily for incompressible flow. This dispersion cloud is then used as the initial condition in an inviscid, compressible, reactive flow simulation. To force detonative ignition, a sufficiently large amount of energy is deposited in a small region that corresponds to the ignition location. Chemistry is modeled using a single step Arrhenius model. Because the wave thickness is small compared with the computational domain, a fine mesh is needed, limiting the practicality of the process to two-dimensional geometries. This is the most significant limitation; it is conservative. The two cases described in the paper include an electrolyzer, in which a small release occurs, leading potentially to some damage to the enclosure, and a reformer, in which the consequences are potentially more serious.     

Meta‐analytic tests of relationships between organizational justice and citizenship behavior: testing agent‐system and shared‐variance models

Research on the unique effects of different types of perceived fairness on citizenship behavior that benefits individuals (organizational citizenship behavior (OCB‐I) and organizations (OCB‐O) has produced mixed results. We assert that how OCB‐O and OCB‐I are conceptualized affects the patterns of results, and we hypothesize that, when OCB is conceptualized appropriately, an agent‐system model is supported (interactional and procedural justice are the strongest unique predictors of OCB‐I and OCB‐O, respectively). We also hypothesize that shared variance among the justice types explains additional variance in OCB. Analyses of semi‐ partial correlations conducted on meta‐analytic coefficients supported our hypotheses. Theoretical and practical implications are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

聚偏氟乙烯中空纤维疏水膜及其初步应用

使用聚偏氟乙烯中空纤维疏水膜,比较了三种膜蒸馏过程用于质量分数为3．5％的氯化钠溶液的脱盐效果。实验结果表明：真空膜蒸馏的通量最大,达到21．8kg／（m^2&#183;h）,其次为直接接触式膜蒸馏,气扫式膜蒸馏的通量最小;三种膜蒸馏过程的脱盐率均在99．99％以上;膜蒸馏通量随膜内径增加略有增加,与膜壁厚呈反比。真空膜蒸馏法可用于反渗透浓水的进一步处理,当反渗透浓水浓缩4倍时,原水电导率从5980μS／cm增加到22800μS／cm,膜蒸馏产水电导率保持在1．8～1．9μS／cm以内,脱盐率大于99．99％。     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.