Study of heat exposure in the work environment in Jeddah

The present work was conducted to define the magnitude of the problem of heat exposure in Jeddah and the role of both the climatic and the industrial factors on the total heat load. Indoor heat exposure was studied in an industrial complex of 5 plants for cables' manufacturing. Outdoor heat exposure was studied in shaded and unshaded operations in Jeddah Islamic Port (JIP). The heat exposure parameters, including air temperature (Ta), wet bulb temperature (Tw), and globe temperature (Tg), as well as the wet bulb globe temperature (WBGT) heat stress index, the relative humidity and the air velocity, were assessed at representative locations. Results of the study indicated that:

Preconcentration of metal ions through chelation on a synthesized resin containing O, O donor atoms for quantitative analysis of environmental and biological samples

Nascent Amberlite XAD-4 has been used as the polymeric support for the synthesis of a stable extractor of metal ions, by incorporating phthalic acid through azo bridging. Elemental analyses and infra-red spectral and thermal studies were carried out for its characterization. The water regain value and hydrogen ion capacity were found to be 12.50 and 5.75 mmol g^?1, respectively. The optimum pH range for the maximum sorption of Ni(II), Mn(II), Cu(II), Zn(II), Cd(II), Cr(III), and Co(II) was observed at pH 5.5–8.0 with the corresponding half-loading time (t _1/2) of 9, 5, 9, 9, 3, 9, and 5 min, respectively. The preconcentration factor for Ni(II), Mn(II), Cu(II), Zn(II), Cd(II), Cr(III), and Co(II) are 190, 190, 190, 180, 180, 160, and 160, with the corresponding limit of preconcentration in the range of 5.25–6.25 μg L^?1. The detection limits, for flame atomic absorption spectrophotometry, were found to be 0.62, 0.60, 0.65, 0.75, 0.72, 0.84, and 0.85 μg L^?1, respectively. Method has been successfully applied to the analysis of water samples, multivitamin formulations, infant food substitutes, hydrogenated oil, and fishes.     

Biopolymer-based membranes from polysaccharides for CO2 separation: a review

Environmental Chemistry Letters - The application of natural biopolymers such as polysaccharides for the fabrication of bio-based membranes has recently attracted attention for CO2...     

Role of plant growth promoting rhizobacteria in the remediation of metal contaminated soils

Pollution of the biosphere by the toxic metals is a global threat that has accelerated dramatically since the beginning of industrial revolution. The primary source of this pollution includes the industrial operations such as mining, smelting, metal forging, combustion of fossil fuels and sewage sludge application in agronomic practices. The metals released from these sources accumulate in soil and in turn, adversely affect the microbial population density and physico-chemical properties of soils, leading to the loss of soil fertility and yield of crops. The heavy metals in general cannot be biologically degraded to more or less toxic products and hence, persist in the environment. Conventional methods used for metal detoxification produce large quantities of toxic products and are cost-effective. The advent of bioremediation technology has provided an alternative to conventional methods for remediating the metal-poisoned soils. In metal-contaminated soils, the natural role of metal-tolerant plant growth promoting rhizobacteria in maintaining soil fertility is more important than in conventional agriculture, where greater use of agrochemicals minimize their significance. Besides their role in metal detoxification/removal, rhizobacteria also promote the growth of plants by other mechanisms such as production of growth promoting substances and siderophores. Phytoremediation is another emerging low-cost in situ technology employed to remove pollutants from the contaminated soils. The efficiency of phytoremediation can be enhanced by the judicious and careful application of appropriate heavy-metal tolerant, plant growth promoting rhizobacteria including symbiotic nitrogen-fixing organisms. This review presents the results of studies on the recent developments in the utilization of plant growth promoting rhizobacteria for direct application in soils contaminated with heavy metals under a wide range of agro-ecological conditions with a view to restore contaminated soils and consequently, promote crop productivity in metal-polluted soils across the globe and their significance in phytoremediation.     

Particleboard manufacturing: an innovative way to recycle paper sludge

This paper presents the results on a study to use paper mill sludge for particleboard production. Single-layer board and three-layer board, with paper sludge on the surface, were fabricated. Four levels of mixing ratios of paper sludge to wood particles (0:100, 15:85, 30:70, and 45:55) were used. The boards were produced with 3% and 4% methylene diphenyl diisocyanate (MDI), and 10% and 12% urea-formaldehyde (UF) adhesives. The bending and shear strengths, water absorption, and thickness swelling of the boards were investigated. The results indicated that the mechanical properties of the boards were negatively affected by the paper sludge amount. Overall, UF-bonded particleboards gave superior mechanical performance, water resistance, and thickness swell than MDI-bonded particleboards. The strengths of the UF-bonded board decreased much more than those of MDI-bonded board as paper sludge content increased. The three-layer boards made from 15% paper sludge with 12% UF satisfied fully the minimum requirements set by EN, ASTM D 1037-99, and ANSI A208.1 standards for general uses.     

Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

Survey on readability of online information for upgrading understandability of biomass energy technology

Waste management contributes to renewable energy such as biodiesel production from processes of various types of biomass including vegetable oils, animal fats, and waste of edible oil. Successful waste management effort is influenced by people concern about benefit of waste management including for renewable energy from biomass. It involves their understanding initiated by literacy on biomass energy. To help increase literacy on waste recycle and biomass energy technology, we study readability of online information regarding biomass energy in Indonesian language (Bahasa Indonesia). Indonesia is considered as one of biomass-rich country with a little utilization for energy. The readability is studied by combining two approaches: measurement by readability standard and survey on readability confirming measurement by the standard. This study focuses on the confirmation survey readability standard measured on biomass online information in Indonesian language. In the survey, 19 online text materials were read by respondents and they were asked to give their impression whether the texts are easy or difficult to understand. From this study, what factors influence understandability of text information are shown. The results could be a guidance for preparing text information to raise people concern on waste recycle and renewable energy in general.     

Municipal solid waste management in Indian cities - A review

Municipal solid waste management (MSWM) is one of the major environmental problems of Indian cities. Improper management of municipal solid waste (MSW) causes hazards to inhabitants. Various studies reveal that about 90% of MSW is disposed of unscientifically in open dumps and landfills, creating problems to public health and the environment. In the present study, an attempt has been made to provide a comprehensive review of the characteristics, generation, collection and transportation, disposal and treatment technologies of MSW practiced in India. The study pertaining to MSWM for Indian cities has been carried out to evaluate the current status and identify the major problems. Various adopted treatment technologies for MSW are critically reviewed, along with their advantages and limitations. The study is concluded with a few fruitful suggestions, which may be beneficial to encourage the competent authorities/researchers to work towards further improvement of the present system.     

Mechanical Properties of Layered Laminated Woven Bamboo <Emphasis Type="Italic">Gigantochloa Scortechinii</Emphasis>/Epoxy Composites

This study investigated the application of bamboo as a natural composite, in which its potential as a composite material had been examined for 2–6 layers. In precise, the woven bamboo (BW) formed the culm fiber composite with an average of 0.5 mm thickness and 5.0 mm width strip. In addition, this study looked into a specific type of bamboo species known as Gigantochloa Scortechinii (Buluh Semantan), which can be found in Malaysia. This laminated plain BW, which had been reinforced with epoxy (EP), was developed by applying the hand lay-up technique. After that, the specimens were characterized via mechanical analyses, for instance, tensile, flexural, hardness, and impact tests. As a result, the 2-layer BW had displayed rather excellent results chiefly due to the incorporation of epoxy composite, although this is exceptional hardness value.