Combustion and inorganic bromine emission of waste printed circuit boards in a high temperature furnace

High temperature combustion experiments of waste printed circuit boards (PCBs) were conducted using a lab-scale system featuring a continuously-fed drop tube furnace. Combustion efficiency and the occurrence of inorganic bromine (HBr and Br₂) were systematically studied by monitoring the main combustion products continuously. The influence of furnace temperature (T) was studied from 800 to 1400 °C, the excess air factor (EAF) was varied from 1.2 to 1.9 and the residence time in the high temperature zone (RT_HT) was set at 0.25, 0.5, or 0.75 s.Combustion efficiency depends on temperature, EAF and RT_HT; temperature has the most significant effect. Conversion of organic bromine from flame retardants into HBr and Br₂ depends on temperature and EAF. Temperature has crucial influence over the ratio of HBr to Br₂, whereas oxygen partial pressure plays a minor role. The two forms of inorganic bromine seem substantially to reach thermodynamic equilibrium within 0.25 s. High temperature is required to improve the combustion performance: at 1200 °C or higher, an EAF of 1.3 or more, and a RT_HT exceeding 0.75 s, combustion is quite complete, the CO concentration in flue gas and remained carbon in ash are sufficiently low, and organobrominated compounds are successfully decomposed (more than 99.9%).According to these results, incineration of waste PCBs without preliminary separation and without additives would perform very well under certain conditions; the potential precursors for brominated dioxins formation could be destroyed efficiently. Increasing temperature could decrease the volume percentage ratio of Br₂/HBr in flue gas greatly.     

Thermal conversion of municipal solid waste via hydrothermal carbonization: comparison of carbonization products to products from current waste management techniques

Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 °C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO(2)-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage).     

TiO2介孔球的合成及其对双酚A的光催化降解

以不同的含钛化合物作为原料,在无模板条件下经一步溶剂热法合成了两种TiO2介孔球——TiO2-1和TiO2-2。对两种TiO2介孔球的形貌进行了表征,结果表明:TiO2-1和TiO2-2粒径分别为5.7 nm和8.0 nm;比表面积分别为159.4 m2/g和128.3 m2/g;孔径约为4.0 nm和5.0 nm。采用P25型TiO2、TiO2-1和TiO2-2对双酚A溶液进行光催化降解反应。在催化剂加入量为0.5 mg/L的条件下降解60 min,双酚A去除率分别为76.3%,99.7%,98.5%。TiO2-1和TiO2-2的光催化效果优于P25型TiO2,且TiO2-1的光催化效果更好。     

仓库计算机网络系统的防雷管理

通过雷电危害及侵入途径的分析,根据仓库建设网络建设实际,探讨了仓库计算机网络雷电防护措施。     

腐殖酸钠和表面活性剂对黄土中石油污染物解吸增溶作用

选用十二烷基苯磺酸钠(LAS)、十二烷基硫酸钠(SDS)和十二烷基磺酸钠(SAS)对污染的土壤进行解吸实验,研究了这3种阴离子表面活性剂和腐殖酸钠对黄土中柴油类污染物的协同增溶作用.结果表明,腐殖酸钠和3种阴离子表面活性剂对黄土中柴油的解吸均有显著增溶作用,使柴油的解吸量明显增加,柴油的去除率最高可达63%.SDS对柴油的解吸量随腐殖酸钠浓度增大呈线性增加关系;但腐殖酸钠浓度增加对 LAS和SAS的解吸曲线有突越点,超过此浓度后反而会抑制解吸作用.     

黄孢原毛平革菌对印染废水脱色条件研究

根据黄孢原毛平革菌的生长和代谢特点,设计了不同废水浓度、不同菌龄、不同温度、不同转速和不同pH值条件,研究黄孢原毛平革菌对工业印染废水的脱色效果.研究表明,印染废水最佳稀释倍数为8倍,脱色用菌丝球最佳接种菌龄为3d,脱色适宜温度为38℃,摇床转速为150～180r/min,脱色初始pH值为3.4～4.6.     

宝钢特种设备计算机管理系统的研究与应用

简述了宝钢特种设备安全管理理念,提出了宝钢特种设备计算机管理系统的总体思路,并对该系统的应用作了一定描述。     

布袋收尘穿漏监测及定位技术现状与展望

综述了国内外布袋收尘穿漏监测及漏袋定位主要技术现状,预测了该技术领域的发展趋势。     

袋式除尘器在化肥厂的应用及改进

对建峰化肥厂包装系统中所使用的袋式除尘器的工作原理、结构性能作了介绍,并对运行情况和改进情况进行了总结,对存在的问题进行了分析,提出了今后改造应注意的问题。     

厌氧折流板反应器处理石化剩余污泥

研究了厌氧折流板反应器(ABR)在厌氧消化处理石化剩余污泥启动过程中的性能及相关参数。实验结果表明:污泥挥发性固体含量的去除率达43.7%;反应器内pH维持在6.4~7.4;从启动到稳定运行,第一隔室最大比产甲烷活性变化不大,在0.14 L/(g·d)以下,第二、第三、第四隔室的最大比产甲烷活性在0.29 L/(g·d)以上,污泥在反应器内部实现了分级分相处理。