全程自养颗粒污泥快速启动及混合营养型脱氮性能分析

在连续流条件下,基于颗粒污泥全程自养脱氮（CANON）工艺的快速启动和混合营养条件下高效脱氮,是CANON工程应用的重要环节.本研究在气提内循环反应器（AIR）中,以老化的CANON颗粒污泥经机械破碎至0.3 mm作为种泥,实现混合营养型单级颗粒污泥同步脱氮除碳.启动26 d,通过控制DO,系统出现稳定的部分硝化,再缩短HRT提升氨氮负荷至5.65 kg ·（m³ ·d）^-1,促进颗粒化和厌氧氨氧化;第68 d,总氮去除率达到58%之后,进水加入有机物,C/N从0提升到0.25和0.5,促进AOB、AMX和异养微生物的协同,氨氮去除率达95%,总氮去除率达85%,COD去除率达80%左右.COD浓度增加,能较好地抑制Nitrospira菌属等NOB的活性,q（NH₄⁺-N）和q（TN）稳定在0.4 g ·（g ·h）^-1和0.34 g ·（g ·h）^-1,q（NO₃^--N）约为0.02 g ·（g ·h）^-1.采用MiSeq高通量测序对微生物多样性分析,表明有机物对污泥中Nitrosomomas和Candidutus_Kuenenia丰度未产生显著影响,增加了Candidutus_Brocadia菌属以及具有反硝化功能Denitratisoma等菌属的丰度.这对于快速启动连续流CANON颗粒污泥工艺处理低C/N比废水提供思路.     

河岸过滤中氨氮的削减及其浓度对细菌与氨氧化微生物的影响

通过小试滤柱模拟河岸过滤,结合荧光定量PCR和高通量测序等手段研究了河岸过滤对氨氮的削减效能和进水氨氮浓度对细菌与氨氧化微生物的影响.结果表明,低浓度（0.2 mg·L^-1）氨氮未被削减,较高浓度（1.0 mg·L^-1和2.0 mg·L^-1）氨氮的削减率可达70%.进水处细菌丰度随氨氮浓度升高而增加,细菌群落组成随氨氮浓度升高发生规律性变化.出水处氨氧化古菌（Ammonia oxidizing archaea,AOA）丰度与氨氮浓度呈负相关,氨氧化细菌（Ammonia oxidizing bacteria,AOB）丰度与氨氮浓度无显著相关关系;进水处AOA-α多样性与氨氮浓度呈正相关,但AOB-α多样性与氨氮浓度呈负相关;进水处AOA群落组成受氨氮浓度影响,而进、出水处AOB群落组成均受氨氮浓度影响.可见,进水氨氮浓度会影响河岸过滤对氨氮的削减效能,还会影响细菌、氨氧化微生物的丰度及群落结构,AOB对氨氮浓度的变化比AOA更敏感.     

核壳结构KNbO3@Co(OH)2的制备及其活化过一硫酸盐降解帕珠沙星的研究

制备了以KNbO₃为载体材料的Co（OH）₂复合材料并对其进行了详细的表征,分析了材料的组成成分、组成形态进而确定了其为核壳结构形貌的KNbO₃@Co（OH）₂.利用合成的样品作为催化剂活化过一硫酸盐（peroxymonosulfate,PMS）来降解帕珠沙星（pazufloxacin,PZF）,结果表明制备的催化剂对PZF的去除效率显著增加.讨论了不同初始PMS剂量对降解效率的影响,发现随着PMS增加可活化生成更多的硫酸根自由基（sulfate radicals,SO₄^·-）和羟基自由基（hydroxyl radicals,HO^·）来降解PZF,但继续增大PMS用量降解效率未见明显提升.酸性和中性pH值条件下利于反应活化PMS降解PZF,而碱性体系减缓反应,甚至强碱体系更易形成Co（OH）₂沉淀不利于反应体系中活性组分CoOH⁺的形成,大大抑制了催化性能.此外,在体系中加入淬灭剂叔丁醇（tert-Butanol,TBA）或者乙醇（ethanol,ETOH）进行自由基的淬灭实验,结果表明SO₄^·-自由基为体系降解PZF过程中主要贡献的自由基,而HO^·自由基的贡献较少.催化剂具有较好的稳定性5次循环之后仍能在10 min之内完全去除PZF.本研究提出了新的思路为制备其他载体的Co（OH）₂核壳结构提供参考依据,同时将该催化剂结合高级氧化技术应用到水体新兴有机污染物净化领域具有很好的应用前景.     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Metabolomic modulations in a freshwater microbial community exposed to the fungicide azoxystrobin

An effective broad-spectrum fungicide, azoxystrobin (AZ), has been widely detected in aquatic ecosystems, potentially affecting the growth of aquatic microorganisms. In the present study, the eukaryotic alga Monoraphidium sp. and the cyanobacterium Pseudanabaena sp. were exposed to AZ for 7 days. Our results showed that 0.2–0.5 mg/L concentrations of AZ slightly inhibited the growth of Monoraphidium sp. but stimulated Pseudanabaena sp. growth. Meanwhile, AZ treatment effectively increased the secretion of total organic carbon (TOC) in the culture media of the two species, and this phenomenon was also found in a freshwater microcosm experiment (containing the natural microbial community). We attempted to assess the effect of AZ on the function of aquatic microbial communities through metabolomic analysis and further explore the potential risks of this compound. The metabonomic profiles of the microcosm indicated that the most varied metabolites after AZ treatment were related to the citrate cycle (TCA), fatty acid biosynthesis and purine metabolism. We thereby inferred that the microbial community increased extracellular secretions by adjusting metabolic pathways, which might be a stress response to reduce AZ toxicity. Our results provide an important theoretical basis for further study of fungicide stress responses in aquatic microcosm microbial communities, as well as a good start for further explorations of AZ detoxification mechanisms, which will be valuable for the evaluation of AZ environmental risk.     

达里诺尔湖水体DOM荧光特征及其来源解析

达里诺尔湖（简称“达里湖”）是内蒙古自治区高原地区重要的生态屏障,探究达里湖水质状况及污染来源,对加强流域水环境治理、改善水环境质量具有十分重要的意义.于2018年9月及2019年6月对湖水进行采样,并通过三维荧光光谱结合PARAFAC（平行因子分析）模型,探究达里湖水体DOM（溶解性有机质）来源及其与水质的关系.结果表明:①达里湖水体中pH较高,ρ（DOC）（DOC为溶解性有机碳）、ρ（NH₄+-N）、ρ（TP）相对较高,均超过GB 3838—2002《地表水环境质量标准》Ⅴ类水质标准限值.②水体中DOM含4种荧光组分.夏季水体DOM主要分布于河流入湖口附近,其中,类腐殖质荧光组分（紫外区类富里酸和可见区类富里酸）占总组分的62.93%,类蛋白类荧光组分（类色氨酸和类酪氨酸）占总组分的36.07%;秋季水体DOM主要分布于东南侧,其中,类腐殖质荧光组分占总组分的40.52%,类蛋白类荧光组分占总组分的59.48%.③达里湖采样点荧光参数表明,达里湖DOM自生源特征较强,腐殖化程度较低.类腐殖质荧光组分与ρ（DOC）、ρ（Chla）均呈正相关,类色氨酸荧光组分与pH呈正相关,类络氨酸与ρ（DTN）、ρ（NH4+-N）、ρ（DTP）均呈正相关.研究显示,达里湖DOM具有陆源与生物源双重特性,DOM的形成与微生物、细菌、浮游生物的生命活动密切相关.      

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。     

基于PCA-SOM的北京市平谷区地下水污染溯源

为了解北京市平谷区地下水污染物来源,以平谷区2010—2018年监测数据为基础,使用PCA(主成分分析法)识别了地下水水质指标因子,使用自组织映射识别了污染物的空间分布.结果表明:通过监测指标间的Pearson检验发现, 平谷区地下水电导率与ρ(Ca2+)(p=0.936)、总碱度与ρ(HCO₃2-)(p=0.981)、ρ(Mg2+)与总硬度(p=0.944)指标之间显著相关.地下水化学类型主要以HCO₃-Ca型为主,其次为HCO₃-Mg型.NH₄+、SO₄2-、Cd、Fe(Ⅱ)、NO₂指标空间分布离散性和差异性较大,存在局部富集现象.通过因子分析法筛选出影响平谷区地下水水质的8个公因子,首要影响因子为溶滤-富集作用(贡献率为22.398%),次要影响因子为农业、养殖业和填埋场等人为活动作用(贡献率为16.533%),雨水下渗作用(贡献率为8.035%)、工业源人为活动(贡献率为7.466%)对地下水也有一定影响.通过比较各指标的SOM(Self-Organizing Map,自组织映射)特征图像和监测井映射特征图像,发现NH₄+受山前地带林业、种植业和平原地带农业、养殖业的双重影响,Na+、Mn受平原地带人为活动的影响;同时,NH₄+、NO₃-、NO₂三者之间及Fe(Ⅱ)与Fe(Ⅲ)之间来源不同,Cd、Al、氰化物三者具有同一来源.研究显示,PCA-SOM(PCA与SOM相结合)可以对地下水化学组分来源进行定性识别与定量分析.