Interactive Influence of Biofiber Composition and Elastomer on Physico-Mechanical Properties of PLA Green Composites

The objective of this work was to improve the impact and thermal properties of polylactic acid (PLA)-based biocomposite by appropriate application of cellulosic fiber and a bioelastomer. Biocomposites formulations with fiber contents of up to 20% in combination with a bioelastomer were extrusion-compounded in a twin-screw extruder followed by molding in an injection molding system. Fibers used in the formulations included three types of cellulosic fiber; namely, raw fiber from oat hull biomass (RF), hydrolysis byproduct (ATF) which was the solid fraction obtained from an acid-catalyzed hydrolysis of RF, and delignified fibers (AD30, AD65, AD100) which were the products of delignification of ATF. Formulated biocomposites were characterized for thermal (glass transition and melting temperatures, and enthalpy of melting) and physico-mechanical (tensile and bending strengths, stiffness, impact energy, and water absorption) properties. Among all types of biofibers, RF resulted in poor properties in the biocomposites due to the high hemicellulose content in the structure. On the other hand, the ratio of lignin to cellulose (in the absence of hemicellulose) in the modified fibers did not significantly affect the physico-mechanical and thermal properties of the biocomposites. The elastomer applied in the formulations improved the impact energy, thermal properties, and elongation at break of the composites. However, it adversely affected the strength and water resistance of biocomposites, especially in the presence of hemicellulose. The results indicated that, depending on the application, a wide range of PLA green composites with different physico-mechanical properties can be achieved.     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

A Comparative Study of Doum fiber and Shrimp Chitin Based Reinforced Low Density Polyethylene Biocomposites

The aim of this paper was to study the effects of reinforcing low density polyethylene (LDPE) by using bio-fillers (Doum cellulose or Shrimp chitin) on the mechanical properties. Both, Doum cellulose extracted frsom Doum leaves and Shrimp chitin extracted from shrimp co-products were compounded with LPDE without and with compatibilizer. The biocomposites were prepared by melt blending in a twin-screw extruder. Torsion and flexural tests were performed to investigate the impact of each reinforcement on the biocomposite mechanical properties. The SEM was carried out to study the filler/polymer interface adhesion. The present study has demonstrated that Doum fibers and shrimp chitin succeed in improving the mechanical properties of LPDE bio-composites. The results also showed that the use of maleic anhydride-grafted polyethylene as a compatibilizer improves filler adhesion/matrix and mechanical properties. This study exhibits that polyethylene composites based on Doum fibers or shrimp chitin can be used to replace the polyethylene materials in several fields like packaging and automotive industries.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Biodegradation of Poly(Aspartic Acid-Itaconic Acid) Copolymers by Miscellaneous Microbes from Natural Water

Poly(aspartic acid-itaconic acid) copolymers (PAI) is a new scale inhibitor for water treatment. Thus, it is necessary to investigate its biodegradability. The biodegradability of PAI was investigated through CO₂ evolution tests under different conditions based on determination of carbon dioxide production. The investigation results showed that the degradation rate of PAI on day 10 and day 28 were respectively 38.7 and 79.5%, indicating that PAI was one kind of easily biodegradable scale inhibitors. With the increase in the content of itaconic acid in copolymerization process, the biodegradability of PAI was significantly reduced. In addition, the high biodegradability might be attributed to the existence of C–N bone-structure and more –COO–. Finally, Cu²⁺ could decrease the degradation percentage and the enzyme inhibition effect of Cu²⁺ was not the linear effect, but the “low-dosage effect”.     

Modification of Thermo-Mechanical Properties of Recycled PET by Vinyl Acetate (VAc) Monomer Grafting Using Gamma Irradiation

Vinyl acetate (VAc) monomer of different percentage was grafted onto the recycled polyethylene terephthalate (r-PET) films using gamma irradiation. The properties of these modified films were characterized by Fourier transform infrared spectroscopy (FTIR), mechanical properties testing (Tensile strength, Elongation at break), dynamic mechanical analysis (DMA) and thermo-gravimetric analysis (TGA). The Tensile Strength (TS) of the modified PET film increased by 132.25?% to the highest value of 50.12 MPa at 15% VAc monomer concentration at 3 kGy gamma dose, while the elongation at break (EB) decreased by 31.83?%. FTIR was used to investigate the molecular interaction of the modified films. TGA revealed that curve of the modified PET film shifted toward higher temperature region by 95?°C, which is very close to that of PET film made from virgin flakes. The results indicate that modified PET films of better mechanical and thermal properties were successfully prepared using VAc monomer grafting by gamma irradiation technique.     

Novel Tough Crystalline Blends of Polylactide with Ethylene Glycol Derivative of POSS

Blending of polylactide (PLA) with low stereoregularity and polyhedral oligomeric silsesquioxane grafted with arms of poly(ethylene glycol) methyl ether, acting as a plasticizer, allowed us previously to obtain a novel stable elastomeric-like material. The present contribution focuses on the properties of semi-crystalline PLA plasticized with this compound. Melt blends of PLA with 5–15 wt% of the plasticizer, were compression molded, quenched and annealed, which enabled cold-crystallization. The glass transition temperature of the blends and their drawability depended on their crystallinity and plasticizer content. The best ductility was reached at the plasticizer content of 15 wt%; the achieved strain at break was 6.5 (650%) and 1.3 (130%), for the quenched and annealed material, respectively. The latter value exceeded 20 times the strain at break of neat crystalline PLA. The tensile toughness of the annealed 15 wt% blend was 12 times larger than that of crystalline PLA. Moreover, annealing of 15 wt% blend improved its yield strength by 40%. Despite the two peaks of the loss modulus, indicating the two glass transitions in this blend, no heterogeneities were found by scanning electron microscopy, indicating that the plasticizer enriched phase formed instead of distinct inclusions of the plasticizer.     

Biodegradability and Thermal Properties of Novel Natural Rubber/Linear Low Density Polyethylene/Thermoplastic Starch Ternary Blends

This work aimed to prepare biodegradable thermoplastic elastomers based on NR/LLDPE/TPS ternary simple blends to achieve some exclusive properties, i.e., good biodegradability in terms of water absorption and weight loss after burial, together with reasonable mechanical and thermal properties. A comparative study on biodegradability and other related properties of NR/LLDPE binary and NR/LLDPE/TPS ternary blends was performed. It was found that increasing the TPS proportion decreased storage modulus and complex viscosity. In addition, the size of dispersed TPS domains in the NR/LLDPE co-continuous matrix increased with TPS proportion, while the mechanical properties in terms of 100% moduli, tensile strength, elongation at break, and hardness decreased. This might be attributed to decreased interfacial adhesion with increasing size of TPS domains. Furthermore, increasing the TPS loading in the blend reduced the temperatures for 5 or 50% mass loss (T₅ or T₅₀) and the degradation temperature (T _d ). However, the biodegradability improved, in terms of increased water absorption and weight loss after burial in soil, with the loading level of TPS.     

Cure,Mechanical and Swelling Properties of Biocomposites from Chicken Feather Fibre and Acrylonitrile Butadiene Rubber

Biocomposites of acrylonitrile butadiene rubber (NBR) reinforced with chicken feather fibre (CF) were prepared using dicumyl peroxide (DCP) as vulcanizing agent. Composites with three series of chicken feather fibres were studied i.e., raw (RCF), sterilized (SCF) and alkali treated (ACF). The cure characteristics of composites were studied. The mechanical properties of NBR were found to be improved by the incorporation of chicken feather fibre in all forms. Surface modification of the fibre was done by alkaline treatment to improve the interfacial adhesion and it characterised by FTIR. Better properties are shown by the composites with ACF. The swelling behaviour of the composites in N,N-dimethylformamide, acetonitrile, dimethyl sulfoxide and water were analyzed for the swelling coefficient values. The biodegradable characteristics of CF reinforced NBR composites were studied by soil burial test which indicated that it is an eco-friendly and acceptable material. Scanning electron microscopy studies support the results of mechanical properties. The outcome obtained from this study is believed to assist the development of environmentally–friendly composites especially for specific product applications like oil seals, hoses and automobile bushes etc.     

A Novel Environmentally Compatible Bio-Based Product from Gelatin and Natural Rubber: Physical Properties

The objective of the present work was to study the preparation of a novel bio-based product from gelatin (GT) and natural rubber (NR) using potassium persulphate (KPS) as an initiator. The GT and NR composites (GT/NR composites) containing KPS were formed in an aqueous latex solution. The chemical structure of the GT/NR composite was characterized by ATR-FTIR, and XRD. The highest tensile strength was observed in a 9/1 GT/NR composite and the elongation at break of this composite was improved by the addition of both NR and glycerol. In addition, the swelling ratio increased as a function of increasing GT content in the composite. The thermal stability of the GT was improved after the formation of the chemical interaction between the NR and GT helped by the KPS. The best ratio of the GT/NR composite was 3/7 GT/NR. This environmentally friendly composite easily decomposed in natural soil within 30 days. The novel biopolymer showed high mechanical properties, water resistance and was produced in an environmentally compatible process. The NR was able to improve some of the physical and mechanical properties of GT biofilms produced from the composite. Possible future applications of this composite are for medical materials, and the packaging and life extension of food products.