The modelling of a hybrid combined cycle with pressurised fluidised bed combustion and CO2 capture

This study investigates the possibility of capturing CO₂ from flue gas under pressurised conditions, which could prove to be beneficial in comparison to working under atmospheric conditions. Simulations of two hybrid combined cycles with pressurised fluidised bed combustion and CO₂ capture are presented. CO₂ is captured from pressurised flue gas by means of chemical absorption after the boiler but before expansion. The results show a CO₂ capture penalty of approximately 8 percentage points (including 90% CO₂ capture rate and compression to 110 bar), which makes the efficiency for the best performing cycle 43.9%. It is 5.2 percentage points higher than the most probable alternative, i.e. using a natural gas fired combined cycle and a pulverised coal fired condensing plant separately with the same fuel split ratio. The largest part of the penalty is associated with the lower mass flow of flue gas after CO₂ capture, which leads to a decrease in work output in the expander and potential for feed water heating. The penalty caused by the regeneration of absorbent is quite low, since the high pressure permits the use of potassium carbonate, which requires less regeneration heat than for example the more commonly proposed monoethanolamine. Although the efficiencies of the cycles look promising it will be important to perform a cost estimate to be able to make a fair comparison with other systems. Such a cost estimate has not been done in this study. A significant drawback of these hybrid cycles in that respect is the complex nature of the systems that will have a negative effect on the economy.     

De-novo formation of dioxins and furans and the memory effect in waste incineration flue gases

The formation of dioxin (polychlorinated-rho-dibenzodioxins - PCDD) and furan (polychlorinated dibenzofurans - PCDF) in waste incineration flyash in relation to temperature has been investigated in a bench scale reactor. The PCDD/PCDF released into the exhaust gases of the reactor and trapped in a condensation and vapour phase adsorption system were also determined. The concentrations of PCDD/PCDF in the flyash were analysed in detail for all congeners and isomers including the mono-, di- and tri-PCDD/PCDF. De-novo synthesis of PCDD/PCDF was clearly seen in the flyash with large changes in concentrations of PCDD/PCDF with only small changes in temperature. Exhaust gas PCDD/PCDF were detected at all temperatures, with the maximum emission occurring at a flyash temperature of 350 degrees C, where the equivalent of over 42 times the total dioxin/furan concentration of the original flyash was lost to the vapour phase per unit mass of initial flyash. Although the desorbed species were mainly the lower mono- to tri-congener group of dioxins and furans, the desorbed dioxin/furans had a considerable toxic equivalent value.     

The effects of aeration rate on generated compost quality, using aerated static pile method

To determine the most appropriate composting process in an active municipal solid waste system, an experiment was carried out using a nested design method with three aeration rates. During each aeration rate, parameters such as temperature, pH, EC, carbon-to-nitrogen ratio, NO(3)-N, nitrogen, potassium and phosphorous were measured and the efficiency of different composting processes was evaluated. The result of this study showed that the lower and medium aeration rates had a significant impact on nitrogen, carbon-to-nitrogen ratio and temperature profile, while higher aeration rates led to higher EC values. Furthermore, the thermophilic phase lasted 13, 9 and 4 weeks for the aeration rates of 0.4, 0.6 and 0.9 L min(-1)kg(-1), respectively. Accordingly, it was concluded that starting at a rate of 0.6 L min(-1)kg(-1) during first 2 months (about 9 weeks) of the process and continuing at a rate of 0.4 L min(-1)kg(-1)until the end of composting process would result in lower energy consumption.     

Bench-scale composting of source-separated human faeces for sanitation

In urine-diverting toilets, urine and faeces are collected separately so that nutrient content can be recycled unmixed. Faeces should be sanitized before use in agriculture fields due to the presence of possible enteric pathogens. Composting of human faeces with food waste was evaluated as a possible method for this treatment. Temperatures were monitored in three 78-L wooden compost reactors fed with faeces-to-food waste substrates (F:FW) in wet weight ratios of 1:0, 3:1 and 1:1, which were observed for approximately 20 days. To achieve temperatures higher than 15 degrees C above ambient, insulation was required for the reactors. Use of 25-mm thick styrofoam insulation around the entire exterior of the compost reactors and turning of the compost twice a week resulted in sanitizing temperatures (>or=50 degrees C) to be maintained for 8 days in the F:FW=1:1 compost and for 4 days in the F:FW=3:1 compost. In these composts, a reduction of >3 log(10) for E. coli and >4 log(10) for Enterococcus spp. was achieved. The F:FW=1:0 compost, which did not maintain >or=50 degrees C for a sufficiently long period, was not sanitized, as the counts of E. coli and Enterococcus spp. increased between days 11 and 15. This research provides useful information on the design and operation of family-size compost units for the treatment of source-separated faeces and starchy food residues, most likely available amongst the less affluent rural/urban society in Uganda.     

Aging and compressibility of municipal solid wastes

The expansion of a municipal solid waste (MSW) landfill requires the ability to predict settlement behavior of the existing landfill. The practice of using a single compressibility value when performing a settlement analysis may lead to inaccurate predictions. This paper gives consideration to changes in the mechanical compressibility of MSW as a function of the fill age of MSW as well as the embedding depth of MSW. Borehole samples representative of various fill ages were obtained from five boreholes drilled to the bottom of the Qizhishan landfill in Suzhou, China. Thirty-one borehole samples were used to perform confined compression tests. Waste composition and volume-mass properties (i.e., unit weight, void ratio, and water content) were measured on all the samples. The test results showed that the compressible components of the MSW (i.e., organics, plastics, paper, wood and textiles) decreased with an increase in the fill age. The in situ void ratio of the MSW was shown to decrease with depth into the landfill. The compression index, Cc, was observed to decrease from 1.0 to 0.3 with depth into the landfill. Settlement analyses were performed on the existing landfill, demonstrating that the variation of MSW compressibility with fill age or depth should be taken into account in the settlement prediction.     

Preferred modes of travel among older adults: What factors affect the choice to walk instead of drive?

Introduction

There are many factors that influence older adults' travel choices. This paper explores the associations between mode of travel choice for a short trip and older adults' personal characteristics.

Methods

This study included 406 drivers over the age of 64 who were enrolled in a large integrated health plan in the United States between 1991 and 2001. Bivariate analyses and generalized linear modeling were used to examine associations between choosing to walk or drive and respondents' self-reported general health, physical and functional abilities, and confidence in walking and driving.

Results

Having more confidence in their ability to walk versus drive increased an older adult's likelihood of walking to make a short trip by about 20% (PR = 1.22; 95% CI: 1.06-1.40), and walking for exercise increased the likelihood by about 50% (PR = 1.53; 95% CI = 1.22-1.91). Reporting fair or poor health decreased the likelihood of walking, as did cutting down on the amount of driving due to a physical problem.

Discussion

Factors affecting a person's decision to walk for exercise may not be the same as those that influence their decision to walk as a mode of travel. It is important to understand the barriers to walking for exercise and walking for travel to develop strategies to help older adults meet both their exercise and mobility needs. Impact on Industry: Increasing walking over driving among older adults may require programs that increase confidence in walking and encourage walking for exercise.     

Implications of turnover and trust for safety attitudes and behaviour in work teams

Turnover potentially leads to a new individual being selected into a work team. This study investigated the safety-specific trust which team members place in their organisation’s selection and induction processes, and related this to the perceived risk from new employees. The research was conducted with teams working in forest harvesting, an occupation which has high-turnover, high risk and a high accident rate. Results indicate that trust in induction processes was negatively correlated with perceived risk from a new employee. Team members also engaged in a number of safety ensuring behaviours when a new individual joined the team, and these were related to the level of perceived risk, and how much they cared about their team members’ safety. It is argued that trust in the safety-specific characteristics of an organisation’s selection and induction process may have negative consequences for safety.     

A method for ranking components importance in presence of epistemic uncertainties

Importance Measures (IMs) are used to rank the contributions of components or basic events to the system performance, e.g. its reliability or risk. Most times, IMs are calculated without due account of the uncertainties in the model of the behavior of the system. The objective of this work is to investigate how uncertainties can influence IMs and to develop a method for giving them due account in the corresponding ranking of the components or basic events. The uncertainties considered in this work affect the model parameters values and are assumed to be described by probability density functions. The method for ranking the contributors to the system performance measure is applied to the auxiliary feedwater system of a nuclear pressurized water reactor.