Surface geophysical exploration: developing noninvasive tools to monitor past leaks around Hanford’s tank farms

A characterization program has been developed at Hanford to image past leaks in and around the underground storage tank facilities. The program is based on electrical resistivity, a geophysical technique that maps the distribution of electrical properties of the subsurface. The method was shown to be immediately successful in open areas devoid of underground metallic infrastructure, due to the large contrast in material properties between the highly saline waste and the dry sandy host environment. The results in these areas, confirmed by a limited number of boreholes, demonstrate a tendency for the lateral extent of the underground waste plume to remain within the approximate footprint of the disposal facility. In infrastructure-rich areas, such as tank farms, the conventional application of electrical resistivity using small point-source surface electrodes initially presented a challenge for the resistivity method. The method was then adapted to directly use the buried infrastructure, specifically the steel-cased wells that surround the tanks, as “long” electrodes for both transmission of electrical current and measurements of voltage. Overcoming the drawbacks of the long electrode method has been the focus of our work over the past 7 years. The drawbacks include low vertical resolution and limited lateral coverage. The lateral coverage issue has been improved by supplementing the long electrodes with surface electrodes in areas devoid of infrastructure. The vertical resolution has been increased by developing borehole electrode arrays that can fit within the small-diameter drive casing of a direct push rig. The evolution of the program has led to some exceptional advances in the application of geophysical methods, including logistical deployment of the technology in hazardous areas, development of parallel processing resistivity inversion algorithms, and adapting the processing tools to accommodate electrodes of all shapes and locations. The program is accompanied by a full set of quality assurance procedures that cover the layout of sensors, measurement strategies, and software enhancements while insuring the integrity of stored data. The data have been shown to be useful in identifying previously unknown contaminant sources and defining the footprint of precipitation recharge barriers to retard the movement of existing contamination.     

Calibration and validation of a regionally and seasonally stratified macroinvertebrate index for West Virginia wadeable streams

Multimetric indices (MMIs) are routinely used by federal, state, and tribal entities to assess the quality of aquatic resources. Because of their diversity, abundance, ubiquity, and sensitivity to environmental stress, benthic macroinvertebrates are well suited for MMIs. West Virginia has used a statewide family-level stream condition index (WVSCI) since 2002. We describe the development, validation, and application of a geographically- and seasonally partitioned genus-level index of most probable stream status (GLIMPSS) for West Virginia wadeable streams. Natural classification strata were evaluated with reference site communities using mean similarity analysis and non-metric multidimensional scaling ordination. Forty-one metrics spanning six ecological categories (richness, composition, tolerance, dominance, trophic groups, and habits) were evaluated for sensitivity, responsiveness, redundancy, range and variability across seasonal (spring and summer) and regional (mountains and plateau) strata. Through a step-wise metric selection process, 8–10 metrics were aggregated to comprise four stratum-specific GLIMPSS models (mountain/plateau and spring/summer). A comparison of GLIMPSS with WVSCI exhibited marked improvements where GLIMPSS detecting greater stream impacts. A variation of the GLIMPSS, which differs only in the family-level taxonomic identification of Chironomidae (GLIMPSS (CF)), was comparable to the full GLIMPSS. These MMIs are robust yet practical tools for evaluating impacts to water quality, instream and riparian habitat, and aquatic wildlife in wadeable riffle-run streams based on sensitivity, responsiveness, precision, and independent validation. These models may be used effectively to detect degradation of the naturally occurring benthic community, assess causes of biological degradation, and plan and evaluate remediation of damaged stream ecosystems.     

Species Distribution Models of Freshwater Stream Fishes in Maryland and Their Implications for Management

Species distribution models (SDMs) are often used in conservation planning, but their utility can be improved by assessing the relationships between environmental and species response variables. We constructed SDMs for 30 stream fishes of Maryland, USA, using watershed attributes as environmental variables and presence/absence as species responses. SDMs showed substantial agreement between observed and predicted values for 17 species. Most important variables were natural attributes (e.g., ecoregion, watershed area, latitude/longitude); land cover (e.g., %impervious, %row crop) was important for three species. Focused analyses on four representative species (central stoneroller, creek chub, largemouth bass, and white sucker) showed the probability of presence of each species increased non-linearly with watershed area. For these species, SDMs built to predict absent, low, and high densities were similar to presence/absence predictions but provided probable locations of high densities (e.g., probability of high-density creek chub decreased rapidly with watershed area). We applied SDMs to predict suitability of watersheds within the study area for each species. Maps of suitability and the environmental and species response relationships can help develop better management plans.     

An Approach to Reaeration Coefficient Modeling in Local Surface Water Quality Monitoring

Reaeration coefficient (k ₂) for River Atuwara, Ogun State, Nigeria was calculated from dissolved oxygen and biochemical oxygen demand data collected over period of 3 months covering the two prevailing climatic seasons in the country. Both the Akaike and Bayesian information criteria were used in the selection and analysis of ten models to identify the most suitable reaeration coefficient (k ₂) model for Atuwara River. Models that passed the confidence limit were subjected to model evaluation using measures of agreement between observed and predicted data such as percent bias, Nash–Sutcliffe efficiency, and root mean square observation standard deviation ratio. The used approach yield better results than empirical models developed for local conditions while it is also useful in conserving scarce resources.     

生物滴滤塔净化挥发性有机废气动力学模型研究

通过对生物滴滤塔净化VOCs废气过程的分析,建立了动力学模型,简化处理后得出了基于生物降解为一级反应动力学和零级反应动力学的污染物浓度沿填料层高度变化的方程,并通过实验数据对方程进行了验证,结果表明基于生物降解一级反应动力学的方程能较好地与实验数据吻合,但常数ξα/Q却随入口浓度Cgi的增大而升高。最后,采用实验数据回归出了ξα/Q随Cg变化的曲线。     

Modelling spills of water-reactive chemicals

This paper describes part of a programme of work undertaken at the Health and Safety Laboratory (HSL) to investigate the behaviour of selected water-reactive chemicals. Following an accidental release, such substances react exothermically with any water present, generating acidic vapours. The STAWaRS (Source Term Assessment of Water Reactive Substances) software was developed for the Health and Safety Executive (HSE) by ESR Technology to model this complex process. The aims of the study described here were to provide experimental validation of the heats of hydrolysis used within STAWaRS, and to perform sensitivity studies on selected STAWaRS input parameters.The heat of hydrolysis of acetyl chloride was measured and showed good correlation with the value used within STAWaRS. Some of the variables that influence the severity of acetyl chloride spills are examined, with reference to predictions made by the STAWaRS model. The heats of hydrolysis of titanium tetrachloride previously measured at HSL are also discussed, and the effect of adopting these experimentally derived values for modelling spills is shown for a hypothetical land use planning case. This study demonstrates the importance of using experimentally validated values for STAWaRS input parameters.     

Effects of significant damage of flame gap surfaces in flameproof electrical apparatus on flame gap efficiency

Electrical apparatus for use in the presence of explosive gas atmospheres has to be specially designed to prevent the apparatus from igniting the gas. Flameproof design is one of several options, and one requirement is then that any holes and slits in the enclosure wall be designed to prevent a possible gas explosion inside the enclosure from being transmitted to an explosive gas cloud outside it. Current standards (IEC) require that joint surfaces have a surface roughness of <6.3 μm. Any damaged joint surface has be restored to this quality. The present investigation has demonstrated that flame gap surfaces in flameproof electrical apparatuses can suffer considerable mechanical and corrosive damage before the flame gaps no longer function satisfactorily. In some cases very significant mechanical surface damage in fact improves the gap performance. This indicates that current high costs of repairing and replacing flameproof electrical apparatus in process plants offshore and onshore can be reduced considerably without any increase of the explosion risk.     

On the development of a new hybrid risk assessment process using occupational accidents’ data: Application on the Greek Public Electric Power Provider

The occupational accidents have a major impact upon human integrity and also bring about high costs for the social health and insurance system of a country. In addition, risk analysis is an essential process for the safety policy of a company, having as main aim the effacement of any potential of damage in a productive procedure, while the quantified risk evaluation is the most crucial part of the whole procedure of assessing hazards in the work. The main goal of this study is double: a) the development and presentation of a new hybrid risk assessment process (HRAP) and b) the application of HRAP in the Greek Public Power Corporation (PPC) (the unique electric power provider and the largest industry in Greece), by using occupational accidents that have been recorded, during the 12-year period of 1993-2004. The new process consists of four distinct phases a) the hazard sources’ identification phase, b) the risk consideration phase, c) the risk-evaluation phase, and d) the phase of the risk assessment and safety-related decision making. The results show that in some cases the risk value has been calculated in PPC to be higher than 500 (in the risk rating of 0-1000), which imposes the taking of suppressive measures for abolishing the danger source, while the fatal accident frequency rate (per 10⁸ man-hrs) is FAFR ≅ 2.4.     

Person–organization and person–supervisor fits: Employee commitments in a Chinese context

The present study simultaneously examined people's perceptions of person–organization (PO) and person–supervisor (PS) fit and related these perceptions to employees' commitments. Three‐hundred‐and‐sixty employee–supervisor dyads from Taiwanese organizations reported about their PO fit and PS fit perceptions. In addition, supervisors reported about their perceptions of fit and guanxi with each of their employees. Results indicated that PO and PS fit perceptions both had an independent and additive relationship with organizational commitment. The link between employee PS fit perceptions and organizational commitment was mediated by commitment to the supervisor. Both employee and supervisor fit perceptions contributed to commitment to the supervisor through their influence on the quality of the leader‐member exchange (LMX). Guanxi could not explain additional variance in LMX and supervisor commitment. Implications for theory and practices regarding person–environment fit, commitment, and LMX are discussed. The study findings offered suggestions for a new Theory of Multiple Fits. Copyright © 2010 John Wiley & Sons, Ltd.