Numerical Modeling of a Potential Geological CO 2 Sequestration Site at Minden (Germany)

We study opportunities for CO₂ sequestration in geological formations of the state North Rhine Westphalia in Germany. Simulations are performed for evaluating a potential site within the Bunter sandstone formation near the town of Minden in a depth?of around 3,000 m using the numerical simulator TOUGHREACT. Our focus is on three CO₂ storage mechanisms: (1) hydrodynamic trapping, (2) dissolution trapping, and (3) mineral trapping. The results show that due to buoyancy the injected CO₂ phase initially migrates towards the top of the reservoir and is hydrodynamically trapped beneath the confining layer of the cap rock. Then, the CO₂ spreads laterally and dissolves partially in the formation water. The dissolution of CO₂ results in an increase of the density of the brine causing a downward migration until it settles after 10,000 years at the bottom of the reservoir. The simulations indicate that after 10,000 years, 15% (17 Mt) from a total of 114 Mt injected CO₂ are trapped hydrodynamically, 20% (23 Mt) are trapped by dissolution, and 65% (74 Mt) are fixed in newly formed carbonates such as dawsonite, ankerite, and siderite. Within our study pressure increases near the injection well by a factor of 1.1 which is lower than the upper limit usually accepted in gas storage operations. The mineral reactions cause a net decrease of porosity and in turn a decrease of permeability down to 9% of the initial value in parts of the reservoir.     

The BIOTA Biodiversity Observatories in Africa—a standardized framework for large-scale environmental monitoring

The international, interdisciplinary biodiversity research project BIOTA AFRICA initiated a standardized biodiversity monitoring network along climatic gradients across the African continent. Due to an identified lack of adequate monitoring designs, BIOTA AFRICA developed and implemented the standardized BIOTA Biodiversity Observatories, that meet the following criteria (a) enable long-term monitoring of biodiversity, potential driving factors, and relevant indicators with adequate spatial and temporal resolution, (b) facilitate comparability of data generated within different ecosystems, (c) allow integration of many disciplines, (d) allow spatial up-scaling, and (e) be applicable within a network approach. A BIOTA Observatory encompasses an area of 1?km² and is subdivided into 100 1-ha plots. For meeting the needs of sampling of different organism groups, the hectare plot is again subdivided into standardized subplots, whose sizes follow a geometric series. To allow for different sampling intensities but at the same time to characterize the whole square kilometer, the number of hectare plots to be sampled depends on the requirements of the respective discipline. A hierarchical ranking of the hectare plots ensures that all disciplines monitor as many hectare plots jointly as possible. The BIOTA Observatory design assures repeated, multidisciplinary standardized inventories of biodiversity and its environmental drivers, including options for spatial up- and downscaling and different sampling intensities. BIOTA Observatories have been installed along climatic and landscape gradients in Morocco, West Africa, and southern Africa. In regions with varying land use, several BIOTA Observatories are situated close to each other to analyze management effects.     

Interlaboratory evaluation of trace element determination in workplace air filter samples by inductively coupled plasma mass spectrometry

Inductively coupled plasma mass spectrometry (ICP-MS) is becoming more widely used for trace elemental analysis in the occupational hygiene field, and consequently new ICP-MS international standard procedures have been promulgated by ASTM International and ISO. However, there is a dearth of interlaboratory performance data for this analytical methodology. In an effort to fill this data void, an interlaboratory evaluation of ICP-MS for determining trace elements in workplace air samples was conducted, towards fulfillment of method validation requirements for international voluntary consensus standard test methods. The study was performed in accordance with applicable statistical procedures for investigating interlaboratory precision. The evaluation was carried out using certified 37-mm diameter mixed-cellulose ester (MCE) filters that were fortified with 21 elements of concern in occupational hygiene. Elements were spiked at levels ranging from 0.025 to 10 μg filter(-1), with three different filter loadings denoted "Low", "Medium" and "High". Participating laboratories were recruited from a pool of over fifty invitees; ultimately twenty laboratories from Europe, North America and Asia submitted results. Triplicates of each certified filter with elemental contents at three different levels, plus media blanks spiked with reagent, were conveyed to each volunteer laboratory. Each participant was also provided a copy of the test method which each participant was asked to follow; spiking levels were unknown to the participants. The laboratories were requested to prepare the filters by one of three sample preparation procedures, i.e., hotplate digestion, microwave digestion or hot block extraction, which were described in the test method. Participants were then asked to analyze aliquots of the prepared samples by ICP-MS, and to report their data in units of μg filter(-1). Most interlaboratory precision estimates were acceptable for medium- and high-level spikes (RSD <25%), but generally yielded greater uncertainties than were anticipated at the outset of the study.     

Preparation, certification and interlaboratory analysis of workplace air filters spiked with high-fired beryllium oxide

Occupational sampling and analysis for multiple elements is generally approached using various approved methods from authoritative government sources such as the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA), as well as consensus standards bodies such as ASTM International. The constituents of a sample can exist as unidentified compounds requiring sample preparation to be chosen appropriately, as in the case of beryllium in the form of beryllium oxide (BeO). An interlaboratory study was performed to collect analytical data from volunteer laboratories to examine the effectiveness of methods currently in use for preparation and analysis of samples containing calcined BeO powder. NIST SRM(?) 1877 high-fired BeO powder (1100 to 1200 °C calcining temperature; count median primary particle diameter 0.12 μm) was used to spike air filter media as a representative form of beryllium particulate matter present in workplace sampling that is known to be resistant to dissolution. The BeO powder standard reference material was gravimetrically prepared in a suspension and deposited onto 37 mm mixed cellulose ester air filters at five different levels between 0.5 μg and 25 μg of Be (as BeO). Sample sets consisting of five BeO-spiked filters (in duplicate) and two blank filters, for a total of twelve unique air filter samples per set, were submitted as blind samples to each of 27 participating laboratories. Participants were instructed to follow their current process for sample preparation and utilize their normal analytical methods for processing samples containing substances of this nature. Laboratories using more than one sample preparation and analysis method were provided with more than one sample set. Results from 34 data sets ultimately received from the 27 volunteer laboratories were subjected to applicable statistical analyses. The observed performance data show that sample preparations using nitric acid alone, or combinations of nitric and hydrochloric acids, are not effective for complete extraction of Be from the SRM 1877 refractory BeO particulate matter spiked on air filters; but that effective recovery can be achieved by using sample preparation procedures utilizing either sulfuric or hydrofluoric acid, or by using methodologies involving ammonium bifluoride with heating. Laboratories responsible for quantitative determination of Be in workplace samples that may contain high-fired BeO should use quality assurance schemes that include BeO-spiked sampling media, rather than solely media spiked with soluble Be compounds, and should ensure that methods capable of quantitative digestion of Be from the actual material present are used.     

Metal concentrations and metallothionein levels in Mytilus galloprovincialis from Elefsis bay (Saronikos gulf, Greece)

Spatial and temporal variability of Cd, Cu, Cr, Ni, Zn, Fe and Mn and metallothionein (MT) concentrations were determined in mussels Mytilus galloprovincialis from Elefsis bay (Saronikos gulf, Greece). Higher concentrations of both metal concentrations and MTs were recorded in mussels inhabiting industrial locations (steelworks and shipyard), indicating a markedly higher metal bioavailability. However at these sites, located at the eastern part of the bay, mussel metal concentrations were not always correlated with both seawater metal concentrations and MTs possibly due to different time scales of integration of the metal sources into mussels and/or the participation of other metal regulatory mechanisms except MT induction. The pattern of the temporal variation of mussel metal concentrations and the MT levels was similar among stations with higher values during the winter–spring season and lower during the summer–autumn period. The inverse relationship of flesh condition index with mussel metal concentrations was attributed to the influence of mussel annual reproductive cycle.     

Bioaccumulation surveillance in Milford Haven Waterway

Biomonitoring of contaminants (metals, organotins, polyaromatic hydrocarbons (PAHs), PCBs) was undertaken in Milford Haven Waterway (MHW) and a reference site in the Tywi Estuary (St Ishmael/Ferryside) during 2007–2008. Bioindicator species encompassed various uptake routes—Fucus vesiculosus (dissolved contaminants); Littorina littorea (grazer); Mytilus edulis and Cerastoderma edule (suspension feeders); and Hediste (=Nereis) diversicolor (sediments). Differences in feeding and habitat preference have subtle implications for bioaccumulation trends though, with few exceptions, contaminant burdens in MHW were higher than the Tywi reference site, reflecting inputs. Elevated metal concentrations were observed at some MHW sites, whilst As and Se (molluscs and seaweed) were consistently at the higher end of the UK range. However, for most metals, distributions in MH biota were not exceptional. Several metal-species combinations indicated increases in bioavailability upstream, which may reflect the influence of geogenic/land-based sources—perhaps enhanced by lower salinity. TBT levels in MH mussels were below OSPAR toxicity thresholds and in the Tywi were close to zero. Phenyltins were not accumulated appreciably in M. edulis, whereas some H. diversicolor populations appear subjected to localized (historical) sources. PAHs in H. diversicolor were distributed evenly across most of MHW, although acenaphthene, fluoranthene, pyrene, benzo(a)anthracene and chrysene were highest at one site near the mouth; naphthalenes in H. diversicolor were enriched in the mid-upper Haven (a pattern seen in M. edulis for most PAHs). Whilst PAH (and PCB) concentrations in MH mussels were mostly above reference and OSPAR backgrounds, they are unlikely to exceed ecotoxicological thresholds. Bivalve Condition indices (CI) were highest at the Tywi reference site and at the seaward end of MH, decreasing upstream—giving rise to several significant (negative) relationships between CI and body burdens. Despite the possible influence of salinity gradient as a complicating factor, multivariate analysis indicated that a combination of contaminants could influence the pattern in condition (and the biomarkers metallothionein and TOSC). Integrating bioaccumulation data with biological and biochemical endpoints is seen as a useful way to discriminate environmental quality of moderately contaminated areas such as MHW and to prioritise cause and effect investigations.