Two-phase jet releases,droplet dispersion and rainout,II. Rainout experiments

This paper describes the results of the first experimental stage of Phase IV of a Joint Industry Project (JIP) on liquid jets and two-phase droplet dispersion. The objective of this stage of the JIP was to generate experimental rainout data for non-flashing water and xylene experiments. See the overview companion paper I for a wider overview of the problem, model implementation and associated model validation.A range of orifice sizes (2.5 and 5 mm) and stagnation pressures (4–16 barg) were applied. Measurements included flow rate, initial droplet size, plume concentrations/temperatures for a range of downstream locations, and distributed rainout.Instead of the Phase Doppler Anemometry method used for droplet size measurements earlier in the JIP, a photographic technique was applied in an attempt to include measurement of the larger (non-spherical) droplets. This enabled a more accurate evaluation of the initial droplet size distribution and a much clearer understanding of the droplet morphology. The results showed that the droplet behaviour in the jet is more complex than had been anticipated with the mass distribution dominated by a very small number of large non-spherical droplets. Consequently a large number of spray images were required to evaluate an accurate size distribution.Distributed rainout was measured by weighing the amount of rainout in trays positioned along the jet direction. The rainout results showed a good degree of repeatability and internal consistency. They indicated that an increasing proportion of the released material did not rainout for increasing pressure. Rainout distance also increased with increasing pressure. Evaporation of the liquid was confirmed by temperature measurements, which showed the effect of evaporative cooling.Xylene concentration measurements (up to 1%) were carried out using a direct reading photoionization detector calibrated for xylene (measuring vapour only). For a limited dataset, the accuracy of these measurements was estimated by means of comparison against an alternative more time-consuming concentration method (xylene absorption onto a charcoal filter; measuring both vapour and liquid). The concentration measurements displayed several consistent qualitative features. For example, at a given downstream distance, the peak concentration increases with increasing pressure and nozzle diameter and the vertical height at which the peak is achieved increases. The cross-stream profiles displayed a consistent tendency to increased concentration at the edge of the jet, and the reason for this has not been established.Finally recommendations are provided for potential future work.     

Worst-case identification of gas dispersion for gas detector mapping using dispersion modeling

To quickly and accurately quantify the material release in process units, gas detectors may be placed according to the results of gas dispersion modeling. DNV's PHAST software is one of the most useful and reliable tools for material dispersion modeling. In this software, fluid dispersion is modeled based on the process conditions, the weather conditions and the specifications of the material release point. However, varying weather conditions throughout the year and the exact determination of the release point on the plot plan and the release elevation are problematic; these issues cause the results to be non-exact and non-integrated. Choosing the most appropriate conditions is challenging. In this paper, a scheme was provided to select the most appropriate conditions for gas dispersion modeling. This scheme approaches modeling based on the worst-case scenario (the situation in which the dispersed gas reaches the detector later in comparison to the other cases). Therefore, different weather conditions, release elevations and release points on the plot plan were modeled for an absorber tower of the Gonbadli Dehydration Unit of the Khangiran Refinery. The worst case of each release condition was then chosen. Finally, gas detectors were placed using the gas dispersion modeling results based on the worst-case scenario.     

Media surface properties and the development of nitrifying biofilms in mixed cultures for wastewater treatment

Plastic was tested to select biofilm support media that would enhance nitrification in the presence of heterotrophs. Eight different types (acrylonitrile butadiene styrene, nylon, polycarbonate, polyethylene, polypropylene, polytetrafluoroethylene (PTFE), polyvinyl chloride and tufnol) were immersed in an aerobic fed-batch reactor receiving domestic settled wastewater. Nitrification rates did not correlate with biomass concentrations, nor surface roughness of the plastics as measured by atomic force microscopy (AFM). The maximum nitrification rate of 1.5 g/m² d^?1 was obtained from biofilms growing on PTFE which had the lowest surface adhesion force (8 nN). Nitrification rates for the biofilms were inversely correlated with the attraction forces as measured by AFM.     

Biological methane production coupled with sulfur oxidation in a microbial electrosynthesis system without organic substrates

Methane is produced in a microbial electrosynthesis system (MES) without organic substrates. However, a relatively high applied voltage is required for the bioelectrical reactions. In this study, we demonstrated that electrotrophic methane production at the biocathode was achieved even at a very low voltage of 0.1 V in an MES, in which abiotic HS⁻ oxidized to SO₄²⁻ at the anodic carbon-cloth surface coated with platinum powder. In addition, microbial community analysis revealed the most probable pathway for methane production from electrons. First, electrotrophic H₂ was produced by syntrophic bacteria, such as Syntrophorhabdus, Syntrophobacter, Syntrophus, Leptolinea, and Aminicenantales, with the direct acceptance of electrons at the biocathode. Subsequently, most of the produced H₂ was converted to acetate by homoacetogens, such as Clostridium and Spirochaeta 2. In conclusion, the majority of the methane was indirectly produced by a large population of acetoclastic methanogens, namely Methanosaeta, via acetate. Further, hydrogenotrophic methanogens, including Methanobacterium and Methanolinea, produced methane via H₂.     

Status of air pollution in Beijing

A study has been made on elements organic constituents, TSP, SO2,NO2 of atmospheric pollutants in Beijing. 17 elements, and some PAHs, e. g. B(a)P, B(b, j, k)P, and B(g, h, i)P, in airborne particles by X-ray fluorescence spectroscopy and HPLC, GC/MS, have been determined respectively. It has been shown that the elements Pb, Zn, S and Cu were more enriched in fine particles and different valence states of sulfur at various sites. It was found that the concentrations of S6+ and S2-were more than 85% and less than 15% of the total sulfur respectively. Concentrations of major PAHs and sulfur-containing compounds increased in winter and in urban area. High values for Pb and Zn in city, Fe and Mn at industrial area and Cu, Al rural sites were obtained respectively. This implies the functions of different elemental sources of various sites. Thus, elements can be from distingushed anthropogenic and natural sources.The main contribution of SO2 was found of to have same seasonal variation as the anthropogenic el     

Development of vermicast from sludge and powdered oyster shell

Soil acidification is one of the rising land degradation issues facing world agriculture. The risk of acidification is currently being assessed as part of agriculture productivity and sustainable theme. This study was conducted to produce a new vermicomposting cast as a recycling resource derived from municipal sewage sludge and waste oyster shell. The earthworm, Eisenia Andrei, was fed under different conditions. The most suitable mixture was 77:23 w/w% of sewage sludge and waste oyster shell. Powdered oyster shell (POS) sludge blend provided a stable pH, due to its buffering capacity during vermiculture because of the Ca²⁺ and OH^? release effect. The vermicast products fulfilled the cast standards of Korea Ministry of Environment for all the parameters such as moisture content, pH, salinity, organic carbon, TKN, Phosphate, and heavy metals. Slowly released organic matter when added to soil improves the capacity of the soil to hold nutrients for plants, improve soil aeration for roots, and improves soil drainage. This product will be an addition to already-commercialized sludge vermicast as a higher value product.