Modeling of Potential Power Plant Plume Impacts on Dallas-Fort Worth Visibility

ABSTRACT

During wintertime, haze episodes occur in the Dallas-Ft. Worth (DFW) urban area. Such episodes are characterized by substantial light scattering by particles and relatively low absorption, leading to so-called “white haze.” The objective of this work was to assess whether reductions in the emissions of SO₂ from specific coal-fired power plants located over 100 km from DFW could lead to a discernible change in the DFW white haze. To that end, the transport, dispersion, deposition, and chemistry of the plume of a major power plant were simulated using a reactive plume model (ROME). The realism of the plume model simulations was tested by comparing model calculations of plume concentrations with aircraft data of SF₆ tracer concentrations and ozone concentrations. A second-order closure dispersion algorithm was shown to perform better than a first-order closure algorithm and the empirical Pasquill-Gifford-Turner algorithm. For plume impact assessment, three actual scenarios were simulated, two with clear-sky conditions and one with the presence of fog prior to the haze. The largest amount of sulfate formation was obtained for the fog episode. Therefore, a hypothetical scenario was constructed using the meteorological conditions of the fog episode with input data values adjusted to be more conducive to sulfate formation. The results of the simulations suggest that reductions in the power plant emissions lead to less than proportional reductions in sulfate concentrations in DFW for the fog scenario. Calculations of the associated effects on light scattering using Mie theory suggest that reduction in total (plume + ambient) light extinction of less than 13% would be obtained with a 44% reduction in emissions of SO₂ from the modeled power plant.     

The potential effect of differential ambient and deployment chamber temperatures on PRC derived sampling rates with polyurethane foam (PUF) passive air samplers

Performance reference compound (PRC) derived sampling rates were determined for polyurethane foam (PUF) passive air samplers in both sub-tropical and temperate locations across Australia. These estimates were on average a factor of 2.7 times higher in summer than winter. The known effects of wind speed and temperature on mass transfer coefficients could not account for this observation. Sampling rates are often derived using ambient temperatures, not the actual temperatures within deployment chambers. If deployment chamber temperatures are in fact higher than ambient temperatures, estimated sampler-air partition coefficients would be greater than actual partition coefficients resulting in an overestimation of PRC derived sampling rates. Sampling rates determined under measured ambient temperatures and estimated deployment chamber temperatures in summer ranged from 7.1 to 10 m³ day⁻¹ and 2.2-6.8 m³ day⁻¹ respectively. These results suggest that potential differences between ambient and deployment chamber temperatures should be considered when deriving PRC-based sampling rates.     

Brominated flame retardants in the Australian population: 1993-2009

Brominated flame retardants, including hexabromocyclododecane (HBCD) and polybrominated diphenyl ethers (PBDEs) are used to reduce the flammability of a multitude of electrical and electronic products, textiles and foams. The use of selected PBDEs has ceased, however, use of decaBDE and HBCD continues. While elevated concentrations of PBDEs in humans have been observed in Australia, no data is available on other BFRs such as HBCD. This study aimed to provide background HBCD concentrations from a representative sample of the Australian population and to assess temporal trends of HBCD and compare with PBDE concentrations over a 16 year period. Samples of human milk collected in Australia from 1993 to 2009, primarily from primiparae mothers were combined into 12 pools from 1993 (2 pools); 2001; 2002/2003 (4 pools); 2003/2004; 2006; 2007/2008 (2 pools); and 2009. Concentrations of ∑HBCD ranged from not quantified (nq) to 19 ng g(-1)lipid while α-HBCD and γ-HBCD ranged from nq to 10 ng g(-1)lipid and nq to 9.2 ng g(-1)lipid. β-HBCD was detected in only one sample at 3.6 ng g(-1)lipid while ∑(4)PBDE ranged from 2.5 to 15.8 ng g(-1)lipid. No temporal trend was apparent in HBCD concentrations in human milk collected in Australia from 1993 to 2009. In comparison, PBDE concentrations in human milk show a peak around 2002/03 (mean ∑(4)PBDEs=9.6 ng g(-1)lipid) and 2003/04 (12.4 ng g(-1)lipid) followed by a decrease in 2007/08 (2.7 ng g(-1)lipid) and 2009 (2.6 ng g(-1)lipid). In human blood serum samples collected from the Australian population, PBDE concentrations did not vary greatly (p=0.441) from 2002/03 to 2008/09. Continued monitoring including both human milk and serum for HBCD and PBDEs is required to observe trends in human body burden of HBCD and PBDEs body burden following changes to usage.     

大气降水重金属含量特征及来源分析

于2010年1月至12月采集鄱阳湖流域8个县市的大气降水样品,用原子吸收分光光度计测定大气降水中溶解态Pb、Cu、Zn、Cd、Cr、Fe等重金属离子,阐述鄱阳湖流域大气降水中重金属含量及分布特征,并分析各种重金属来源。结果表明,Pb年际平均质量浓度为9.53μg/L,Cu为11.32μg/L,Zn为33.73μg/L,Cd为1.55μg/L,Cr为9.09μg/L,Fe为142.65μg/L。Pb、Cu、Cd、Cr受人为因素影响较大,主要来源于第二产业和第三产业,Zn和Fe受人类影响较小,Zn主要来源为天然源,Fe来源于混合源。     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

两个海州香薷种群根对Cu的吸收及Cu诱导的ATP酶活性差异

通过水培实验,比较分析了分别来自湖北省铜绿山矿区和红安非矿区的海洲香薷种群根对铜的抗性和对Cu的吸收累积差异,同时应用微囊膜技术进行了ATPase的诱导和活性测定.结果发现,来自铜绿山种群植物的铜耐受性明显高于红安种群,在20μmol·L-1 Cu处理时红安种群根尖开始变黑,生长明显受到抑制;而铜绿山种群在80μmol·L-1 Cu处理时仍然能正常生长;在所有Cu处理中,铜绿山种群植物根的Cu含量明显低于红安种群.Cu诱导的ATPase活性在铜绿山种群根质膜有明显的变化,在1μmol·L-1 Cu处理时,其活性显著增加,5μmol·L-1 Cu处理时,其活性先到达高峰而后降低;而红安种群则没有出现Cu诱导的ATPase活性的升高,除了100μmol·L-1 Cu明显降低了ATPase活性外,其它处理则没有显著的变化.在还原型谷光苷肤(GSH)存在的条件下,Cu诱导的ATPase活性在铜绿山种群中显著提高,且有明显的Cu浓度效应,而红安种群虽有提高但没有浓度效应.这些结果表明,矿区种群根细胞中可能存在Cu-ATPase,该酶在根的Cu吸收运输方面可能起重要的调节作用,从而使其具有较高的Cu抗性.     

三油酸甘油脂-醋酸纤维素复合膜测定水中有机氯农药生物有效性

以异狄氏剂、狄氏剂和p,p'-滴滴涕3种持久性有机氯农药为研究对象,通过室内模拟实验,验证了三油酸甘油脂-醋酸纤维素复合膜(TECAM)富集水中自由溶解态疏水性有机物的假设,研究了水中溶解性有机碳对TECAM富集3种有机氯农药的影响,并与相同暴露条件下日本青鳉鱼的富集结果进行了比较.结果表明,TECAM只富集水中自由溶解形态的疏水性有机物;水中存在的溶解性有机碳会降低3种有机氯农药被TECAM和青鳉富集的可利用性;TECAM和青鳉的富集结果有很好的可比性.因此,TECAM能够用来预测疏水性有机污染物在不同溶解性有机碳含量的水中被鱼体富集的生物有效性.     

Removal of PFOS, PFOA and other perfluoroalkyl acids at water reclamation plants in South East Queensland Australia

This paper examines the fate of perfluorinated sulfonates (PFSAs) and carboxylic acids (PFCAs) in two water reclamation plants in Australia. Both facilities take treated water directly from WWTPs and treat it further to produce high quality recycled water. The first plant utilizes adsorption and filtration methods alongside ozonation, whilst the second uses membrane processes and advanced oxidation to produce purified recycled water. At both facilities perfluorooctane sulfonate (PFOS), perfluorohexane sulfonate (PFHxS), perfluorohexanoic acid (PFHxA) and perfluorooctanoic acid (PFOA) were the most frequently detected PFCs. Concentrations of PFOS and PFOA in influent (WWTP effluent) ranged up to 3.7 and 16 ng L⁻¹ respectively, and were reduced to 0.7 and 12 ng L⁻¹ in the finished water of the ozonation plant. Throughout this facility, concentrations of most of the detected perfluoroalkyl compounds (PFCs) remained relatively unchanged with each successive treatment step. PFOS was an exception to this, with some removal following coagulation and dissolved air flotation/sand filtration (DAFF). At the second plant, influent concentrations of PFOS and PFOA ranged up to 39 and 29 ng L⁻¹. All PFCs present were removed from the finished water by reverse osmosis (RO) to concentrations below detection and reporting limits (0.4-1.5 ng L⁻¹). At both plants the observed concentrations were in the low parts per trillion range, well below provisional health based drinking water guidelines suggested for PFOS and PFOA.     

Emissions of PCDD and PCDF from combustion of forest fuels and sugarcane: a comparison between field measurements and simulations in a laboratory burn facility

Release of PCDD and PCDF from biomass combustion such as forest and agricultural crop fires has been nominated as an important source for these chemicals despite minimal characterisation. Available emission factors that have been experimentally determined in laboratory and field experiments vary by several orders of magnitude from <0.5 μg TEQ (t fuel consumed)⁻¹ to >100 μg TEQ (t fuel consumed)⁻¹. The aim of this study was to evaluate the effect of experimental methods on the emission factor.A portable field sampler was used to measure PCDD/PCDF emissions from forest fires and the same fuel when burnt over a brick hearth to eliminate potential soil effects. A laboratory burn facility was used to sample emissions from the same fuels. There was very good agreement in emission factors to air (EF_Air) for forest fuel (Duke Forest, NC) of 0.52 (range: 0.40-0.79), 0.59 (range: 0.18-1.2) and 0.75 (range: 0.27-1.2) μg TEQ_WHO2005 (t fuel consumed)⁻¹ for the in-field, over a brick hearth, and burn facility experiments, respectively. Similarly, experiments with sugarcane showed very good agreement with EF_Air of 1.1 (range: 0.40-2.2), 1.5 (range: 0.84-2.2) and 1.7 (range: 0.34-4.4) μg TEQ (t fuel consumed)⁻¹ for in-field, over a brick hearth, open field and burn facility experiments respectively. Field sampling and laboratory simulations were in good agreement, and no significant changes in emissions of PCDD/PCDF could be attributed to fuel storage and transport to laboratory test facilities.     

Concentrations of PFOS, PFOA and other perfluorinated alkyl acids in Australian drinking water

Perfluorinated alkyl acids (PFAAs) are persistent environmental pollutants, found in the serum of human populations internationally. Due to concerns regarding their bioaccumulation, and possible health effects, an understanding of routes of human exposure is necessary. PFAAs are recalcitrant in many water treatment processes, making drinking water a potential source of human exposure. This study was conducted with the aim of assessing the exposure to PFAAs via potable water in Australia. Sixty-two samples of potable water, collected from 34 locations across Australia, including capital cities and regional centers. The samples were extracted by solid phase extraction and analyzed via liquid chromatography/tandem mass spectrometry for a range of perfluoroalkyl carboxylates and sulfonates. PFOS and PFOA were the most commonly detected PFAAs, quantifiable in 49% and 44% of all samples respectively. The maximum concentration in any sample was seen for PFOS with a concentration of 16 ng L⁻¹, second highest maximums were for PFHxS and PFOA at 13 and 9.7 ng L⁻¹. The contribution of drinking water to daily PFOS and PFOA intakes in Australia was estimated. Assuming a daily intake of 1.4 and 0.8 ng kg⁻¹ bw for PFOS and PFOA the average contribution from drinking water was 2-3% with a maximum of 22% and 24% respectively.