磺胺类抗生素在斑马鱼体内的生物富集性及模型预测评估

针对磺胺类抗生素在鱼体内的生物富集特性,采用半静态生物富集测试法,研究磺胺二甲嘧啶(SMT)和磺胺甲恶唑(SMX)在斑马鱼(Brachydanio rerio)体内的生物富集规律及生物富集系数(bio-concentration factor,BCF),并选用3种常用预测模型对2种磺胺类抗生素的BCF值进行估算,比较了估算值与实际测定值,为磺胺类抗生素生物富集性的预测提供依据。研究结果表明,当暴露浓度为0.01 mg·L~(-1)~1.00 mg·L~(-1)时,鱼体对SMT的最大生物富集系数BCF值为1.11,最大富集量出现在暴露24~48 h期间;SMX的最大BCF值为1.15,最大富集量处于暴露96~168 h之间。根据磺胺类抗生素的理化性质,通过比较3种生物富集预测模型获得SMT和SMX的BCF值,发现其中Kow预测模型所得估算值最为接近实测值。因此可利用该模型作为磺胺类抗生素富集性的预测工具,为我国兽药抗生素的环境风险预测和评价提供依据。     

四川省卧龙地区土壤中二噁英类化合物和多氯萘的海拔梯度分布及对牦牛的毒性风险评价

初步研究了四川省卧龙地区5个不同海拔高度的表层土壤和2个牦牛样品中二噁英/呋喃(PCDD/Fs)、共平面多氯联苯(co-PCBs)和多氯萘(PCNs)的分布特征、来源、毒性当量以及生态风险状况.土壤样品中总2,3,7,8-PCDD/Fs的含量范围为2.48-4.30 pg·g-1dw,平均3.50 pg·g-1dw,最高含量在海拔3927 m的塘房.co-PCBs的总含量平均为9.14 pg·g-1dw,最高值在海拔4487 m的垭口.总2,3,7,8-PC-DD/Fs和总co-PCBs含量随海拔高度的变化表现出正相关关系.不同海拔高度土壤中的PCDD/Fs和co-PCBs异构体的分布相似,表明具有相同的来源.总PCNs与海拔梯度呈负相关关系,最高含量出现在海拔3345 m的贝母坪,平均21.4 pg·g-1dw,主要以3.氯为主.土壤中PcDD/Fs毒性当量浓度范围为0.29-0.43pg TEQ·g-1dw.牦牛肉和牦牛组织中PcDD,/Fs总浓度分别为27.5和23.6 pg·g-1脂肪,毒性当量浓度为4.04和4.07 pg TEQ·g-1脂肪.结果表明,牦牛中的PCDD/Fg,co-PcBs和PCNs不大可能对卧龙地区人群导致严重的负面效应.     

Effects of distillery waste on the performance of Cicer arietinum L

The impact of distillery effluent in various concentrations (1, 2.5, 5, 10, 25, 50, 75 and 100%) on the seed germination, Speed of Germination Index, growth behaviour, leaf area, biomass, net primary productivity, pigment content, reproductive capacity, seed output, seed weight, seed density and the seed protein content of Cicer arietinum L. plants was investigated. The percentage and speed of germination of seeds were increasingly retarded with increase in effluent concentration and at 100% concentration there was no germination. The seedlings exhibited maximum shoot length at 5% concentration and maximum root length at 2.5% concentration. The values of root and shoot lengths, leaf area, biomass, net primary productivity, pigment content, reproductive capacity, seed output, seed weight, seed density and seed protein content in pot plants exhibited a gradual increase from the control up to 5% concentration and decreases at higher concentrations. The very high BOD load and the presence of excessive concentrations of soluble salts could be responsible for the toxicity of the effluent. The effluent at up to 5% concentration was, however, beneficial for the overall growth parameters studied and can thus be used as a liquid fertilizer.     

Quantifying road dust resuspension in urban environment by Multilinear Engine: A comparison with PMF2

Atmospheric PM pollution from traffic comprises not only direct emissions but also non-exhaust emissions because resuspension of road dust that can produce high human exposure to heavy metals, metalloids, and mineral matter. A key task for establishing mitigation or preventive measures is estimating the contribution of road dust resuspension to the atmospheric PM mixture. Several source apportionment studies, applying receptor modeling at urban background sites, have shown the difficulty in identifying a road dust source separately from other mineral sources or vehicular exhausts. The Multilinear Engine (ME-2) is a computer program that can solve the Positive Matrix Factorization (PMF) problem. ME-2 uses a programming language permitting the solution to be guided toward some possible targets that can be derived from a priori knowledge of sources (chemical profile, ratios, etc.). This feature makes it especially suitable for source apportionment studies where partial knowledge of the sources is available.In the present study ME-2 was applied to data from an urban background site of Barcelona (Spain) to quantify the contribution of road dust resuspension to PM₁₀ and PM_2.5 concentrations. Given that recently the emission profile of local resuspended road dust was obtained (Amato, F., Pandolfi, M., Viana, M., Querol, X., Alastuey, A., Moreno, T., 2009. Spatial and chemical patterns of PM₁₀ in road dust deposited in urban environment. Atmospheric Environment 43 (9), 1650–1659), such a priori information was introduced in the model as auxiliary terms of the object function to be minimized by the implementation of the so-called “pulling equations”.ME-2 permitted to enhance the basic PMF solution (obtained by PMF2) identifying, beside the seven sources of PMF2, the road dust source which accounted for 6.9 μg m^?3 (17%) in PM₁₀, 2.2 μg m^?3 (8%) of PM_2.5 and 0.3 μg m^?3 (2%) of PM₁. This reveals that resuspension was responsible of the 37%, 15% and 3% of total traffic emissions respectively in PM₁₀, PM_2.5 and PM₁. Therefore the overall traffic contribution resulted in 18 μg m^?3 (46%) in PM₁₀, 14 μg m^?3 (51%) in PM_2.5 and 8 μg m^?3 (48%) in PM₁. In PMF2 this mass explained by road dust resuspension was redistributed among the rest of sources, increasing mostly the mineral, secondary nitrate and aged sea salt contributions.     

Antimony distribution and environmental mobility at an historic antimony smelter site, New Zealand

A historic antimony smelter site at Endeavour Inlet, New Zealand has smelter residues with up to 17 wt.% antimony. Residues include coarse tailings (cm scale particles, poorly sorted), sand tailings (well sorted) and smelter slag (blocks up to 30 cm across). All of this material has oxidised to some degree over the ca. 100 years since the site was abandoned. Oxidation has resulted in acidification of the residues down to pH 2-5. Smelter slag contains pyrrhotite (FeS) and metallic antimony, and oxidation is restricted to surfaces only. The coarse tailings are the most oxidised, and few sulfide grains persist. Unoxidised sand tailings contain 10-20 vol.% stibnite (Sb2S3) containing up to 5% As, with subordinate arsenopyrite (FeAsS), and minor pyrite (FeS2). The sand tailings are variably oxidised on a scale of 2-10 cm, but original depositional layering is preserved during oxidation and formation of senarmontite (Sb2O3). Oxidation of sand tailings has resulted in localised mobility of both Sb and As on the cm scale, resulting in redistribution of these metalloids with iron oxyhydroxide around sand grain boundaries. Experiments demonstrate that Sb mobility decreases with time on a scale of days. Attenuation of both As and Sb occurs due to adsorption on to iron oxyhydroxides which are formed during oxidation of the smelter residues. There is no detectable loss of Sb or As from the smelter site into the adjacent river, <50 m away, which has elevated Sb (ca. 20 microg/l) and As (ca. 7 microg/l) from mineralised rocks upstream. Despite the high concentrations of Sb and As in the smelter residues, these metalloids are not being released into the environment.     

The occurrence of xenoestrogens in the Elbe river and the North Sea

The xenoestrogens Bisphenol A (BPA), p-alkylphenols and p-alkylphenol ethoxylates were determined in water samples of the North Sea, the Elbe river, and its tributaries Schwarze Elster, Mulde, Saale and the Weisse Elster. The sampling sites of the Elbe river reached from Schmilka at the German-Czech border to Cuxhaven at the estuary. Samples of the North Sea were taken in the German Bight. Additionally, freshly deposed sediments of the River Elbe and its tributaries were analyzed. Partitioning coefficients of these compounds for the distribution between suspended particulate matter (SPM) and the aqueous phase were calculated for samples of the River Elbe at sampling site Geesthacht. The analytical procedure consisted of liquid-liquid extractions of the acidified water samples using dichloromethane. Sediments and SPM samples were extracted by Accelerated Solvent Extraction with n-hexane/acetone. Following a clean-up by HPLC, the analytes were derivatized with heptafluorobutyric acid anhydride and quantified using GC-MSD. The concentration ranges of the compounds analyzed in water samples of the Elbe river were as follows (in ng l(-1)): BPA 9-776, alkylphenols 10-221 and alkylphenol ethoxylates 18-302. In sediment samples the concentrations were (in microg kg(-1) dry mass): BPA 66-343, alkylphenols 17-1378 and alkylphenol ethoxylates 30-1797. In samples of the North Sea the concentrations were generally about 1 order of magnitude lower. As shown by the concentration profiles following the River Elbe into the North Sea, the Elbe river must be considered as a major pollution source for the North Sea concerning the compounds analyzed. The SPM/water-partitioning coefficients calculated (mean values) amounted to: BPA 4.50, alkylphenols 5.52-5.58 and alkylphenol ethoxylates 5.60-6.38. A comparison of the results with data from other surface waters showed that concentrations of these xenoestrogens in the River Elbe and its tributaries were relatively low. The evaluation of the data based on the lowest observable effect concentration (LOEC) for alkylphenols (endpoint: vitellogenin synthesis in male trout) indicated that the concentrations were well below the effectivity threshold.     

Organochlorinated contaminants in decapod crustaceans from the coasts of Brittany and Normandy (France)

The contamination and distribution of organochlorinated compounds were considered in three crustacean species (edible crab, Cancer pagurus; spider crab, Maja brachydactyla; velvet swimming crab, Necora puber) from five sites along the coasts of Brittany and Normandy (Western and North-Western France). PCBs (16 single congeners), pp'-DDE and HCB were measured in hepatopancreas, gonads and muscle: in all, 175 samples were analysed. The spider crab was the only species found in the five sampling sites, thus enabling comparison between areas. Specimens from Antifer were much more contaminated (summation operator 16 PCBs in hepatopancreas=2000-4000 ng g(-1) dry weight) than those from other sites (50-1000 ng g(-1) d.w.). Among all the three species, the spider crab appeared more contaminated by PCBs than the edible crab, by a factor 2-3, probably in relation with specific differences in their life cycle. There was no difference due to the gender of the species. Within the different analysed tissues, contamination levels increased from muscle to gonads and hepatopancreas in relation with the fat content. A very similar PCB composition was observed in all samples, PCB fingerprints being characterised by the relative importance of the more persistent PCB congeners: CB153, 138, 180, 187, and 118. Finally, these results were compared to recent food regulations first of maximum marker PCB intake and secondly of maximum dioxin-like PCB intake. By considering the muscle, all samples were far below the regulatory limits; for hepatopancreas and gonads, however, some samples were unfit for human consumption.     

Development of a new quality fair access best value performance indicator (BVPI) for recycling services

Recycling schemes are being used worldwide to reduce the impact of municipal waste. Those using public funds are usually obliged to set performance indicators by which the standards of such schemes can be measured. In the UK, a set of statutory Best Value Performance Indicators (BVPI) must be reported annually, such as the Quality of Fair Access, which monitors the public's access to recycling facilities within 1000 m (known as BVPI 91). This work shows that BVPI 91, and performance indicators like it, quantify only very basic recycling services. A much more sensitive performance indicator is developed in this paper, labelled as the Maximum Practicable Recycling Rate Provision (MPRRP) achievable by a local authority. It indicates the percentage of local waste that could be reasonably recycled using the services provided, calculated on the basis of the average composition of the local waste, the local population coverage for collection of any materials, and nationally provided information stating how much of each material stream is generally suitable (practical) for recycling. Evidence for the usefulness of this new quantity is presented. Although this paper refers a particular performance indicator in the UK, its findings are applicable to all urban areas worldwide needing to monitor recycling service. Furthermore, the MPRRP could be used for planning purposes, and for determining the level of performance of an existing service, by comparing its predicted recycling rate to that actually obtained. Further work is now being carried out on this.     

Treatment of drainage water with industrial by-products to prevent phosphorus loss from tile-drained land

Tile drained land with phosphorus (P)-rich topsoil is prone to P loss, which can impair surface water quality via eutrophication. We used by-products from steel and energy industries to mitigate P loss from tile drains. For each by-product, P sorption maximum (P(max)) and strength (k) were determined, while a fluvarium trial assessed P uptake with flow rate. Although two ash materials (fly ash and bottom ash) had high P(max) and k values, heavy metal concentrations negated their use in the field. The fluvarium experiment determined that P uptake with by-products was best at low flow, but decreased at higher flow in proportion to k. A mixture of melter slag (<10 mm) and basic slag (high P(max), 7250 mg kg(-1); and k, 0.508 L mg P(-1)) was installed as backfill in eight drains on a dairy farm. Four drains with greywacke as backfill were constructed for controls. The site (10 ha) had P-rich topsoil (Olsen P of 64 mg kg(-1)) and yielded a mean dissolved reactive P (DRP) and total P (TP) concentration from greywacke backfilled drains of 0.33 and 1.20 mg L(-1), respectively. In contrast, slag backfilled drains had DRP and TP concentrations of 0.09 and 0.36 mg L(-1), respectively. Loads of DRP and TP in greywacke drains (0.45 and 1.92, respectively) were significantly greater (P < 0.05) than those from slag drains (0.18 and 0.85, respectively). Data from a farm where melter slag was used as a backfill suggested that slag would have a life expectancy of about 25 yr. Thus, backfilling tile drains with melter slag and a small proportion of basic slag is recommended as an effective means of decreasing P loss from high P soils.     

Estimated occupational risk from bioaerosols generated during land application of class B biosolids

Some speculate that bioaerosols from land application of biosolids pose occupational risks, but few studies have assessed aerosolization of microorganisms from biosolids or estimated occupational risks of infection. This study investigated levels of microorganisms in air immediately downwind of land application operations and estimated occupational risks from aerosolized microorganisms. In all, more than 300 air samples were collected downwind of biosolids application sites at various locations within the United States. Coliform bacteria, coliphages, and heterotrophic plate count (HPC) bacteria were enumerated from air and biosolids at each site. Concentrations of coliforms relative to Salmonella and concentrations of coliphage relative to enteroviruses in biosolids were used, in conjunction with levels of coliforms and coliphages measured in air during this study, to estimate exposure to Salmonella and enteroviruses in air. The HPC bacteria were ubiquitous in air near land application sites whether or not biosolids were being applied, and concentrations were positively correlated to windspeed. Coliform bacteria were detected only when biosolids were being applied to land or loaded into land applicators. Coliphages were detected in few air samples, and only when biosolids were being loaded into land applicators. In general, environmental parameters had little impact on concentrations of microorganisms in air immediately downwind of land application. The method of land application was most correlated to aerosolization. From this large body of data, the occupational risk of infection from bioaerosols was estimated to be 0.78 to 2.1%/yr. Extraordinary exposure scenarios carried an estimated annual risk of infection of up to 34%, with viruses posing the greatest threat. Risks from aerosolized microorganisms at biosolids land application sites appear to be lower than those at wastewater treatment plants, based on previously reported literature.