Rotary Kiln Incineration II. Laboratory-Scale Desorption and Kiln-Simulator Studies—Solids

With landfill costs increasing and regulations on landfilling becoming more stringent, alternatives to conventional hazardous waste treatment strategies are becoming more desirable. Incineration Is presently a permanent, proven solution for the disposal of most organic contaminants, but also a costly one, especially in the case of solids which require some auxiliary fuel. The goal of this research is to develop an understanding of the phenomena associated with the evolution of contaminants from solids In the primary combustor of an Incineration system. A four-fold approach is being used. First, a bench-scale particle characterization reactor was developed to study the transport phenomena on a particle basis, where the controlling processes are mainly intraparticle. Second, a bed-characterization reactor was built to examine the controlling transport phenomena within a bed of particles, where the processes are primarily interparticle. The results of these studies can be applied to any primary combustor. A pilot-scale rotary kiln was developed to study the evolution of contaminants from solids within a realistic temperature and rotation environment. Finally, in situ measurements are being obtained from a full-scale rotary-kiln.

This paper describes results obtained in a study using a commercial sorbent contaminated with toluene. The data are from the particle-characterization reactor and the rotary-kiln simulator. The results show that the method of contamination and charge size do not have a large effect on desorption, while temperature and contaminant concentration are important parameters In the evolution of contaminants in a rotary kiln.     

A Combined Ca(OH)2/NH3 Flue Gas Desulfurization Process for High Sulfur Coal: Results of a Pilot Plant Study

The removal of SO₂ with atomization of a slaked lime slurry and supplemental injection of gaseous NH₃ were tested in a conventional spray dryer/baghouse system for SO₂ concentrations of 2000 ppm and 3000 ppm and a 30° F approach to saturation. Results at 3000 ppm of SO₂ showed an average SO₂ removal efficiency of 90.3 percent at a combined stoichiometric ratio of 0.95-1.10 and an average overall sorbent utilization of 91.6 percent. The overall molal ratio of NH₃/SO₂ reaction was found to be 2:1 under the test conditions Particle size analyses, and EP toxicity tests were conducted on the products of the reactions.     

Evaluating Sources of Indoor Air Pollution

Evaluation of Indoor air pollution problems requires an understanding of the relationship between sources, air movement, and outdoor air exchange. Research is underway to investigate these relationships. A three-phase program is being implemented: 1) Environmental chambers are used to provide source emission factors for specific indoor pollutants; 2) An IAQ (Indoor Air Quality) model has been developed to calculate indoor pollutant concentrations based on chamber emissions data and the air exchange and air movement within the indoor environment; and 3) An IAQ test house is used to conduct experiments to evaluate the model results. Examples are provided to show how this coordinated approach can be used to evaluate specific sources of indoor air pollution. Two sources are examined: 1) para-dichlorobenzene emissions from solid moth repellant; and 2) particle emissions from unvented kerosene heaters.

The evaluation process for both sources followed the three-phase approach discussed above. Para-dichlorobenzene emission factors were determined by small chamber testing at EPA’s Air and Energy Engineering Research Laboratory. Particle emission factors for the kerosene heaters were developed In large chambers at the J. B. Pierce Foundation Laboratory. Both sources were subsequently evaluated in EPA’s IAQ test house. The IAQ model predictions showed good agreement with the test house measurements when appropriate values were provided for source emissions, outside air exchange, in-house air movement, and deposition on “sink” surfaces.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

The Cost Estimation of Thermal and Catalytic Incinerators for the Control of VOCs

In an earlier paper, major commercially available incinerator technologies designed to treat dilute waste gas streams containing volatile organic compounds (VOCs) were described in a qualitative comparison. In addition, a simplified procedure was outlined through which important sizing parameters could be calculated given certain information about the waste gas. This paper describes the use of these parameters in developing a study (±30percent) cost estimate for the total capital investment and the total annual costs incurred in treating a waste stream of volatile organic compounds (VOCs). An illustrative problem used in the former paper is completed here in order to contrast some of the economic differences between thermal and catalytic incinerator systems.     

An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

A Methodological Approach for Exposure Assessment Studies in Residences Using Volatile Organic-Compound-Contaminated Water

Abstract

This paper presents a methodological approach for assessing total exposures to volatile organic compounds (VOCs) in residences using contaminated water supplies. This approach is founded on assessment of ingestion, inhalation, and dermal exposures; both long-term (i.e., 12 to 24 hr) lowlevel exposures and short-term (i.e., =10 min) high-level exposures are considered.

The methodology is based on the collection of water samples to establish the identity of the contaminants, maximum source terms, and possible dermal and ingestion exposures; integrated whole-air samples are collected to assess long- and short-term inhalation exposures; whole-air grab samples are used to confirm peak and typical inhalation exposures; and alveolar breath samples are used to confirm exposures and to estimate contaminant concentrations in the blood of the test subjects. While we do not suggest that this methodology should supersede any current investigative approach, this material is primarily offered as a consolidated reference to the many people or organizations who might contemplate a study of this type. Application of this investigative protocol should provide detailed exposure assessment information, while it supplies critical real world data for risk assessment specialists, toxicologists, and modeling experts. Data from a recent field study assessing exposures to trichloroethylene are presented to illustrate the utility and some of the limitations of this strategy.     

Seasonal Variability in CH4 Emissions from a Landfill in a Cool,Semiarid Climate

ABSTRACT

Methane exchange with the atmosphere was measured during three seasons at the Rooney Road landfill in Jefferson County, CO. Substantial spatial and temporal variability in exchange rates were observed. Mean fluxes to the atmosphere were 534, 1290, and 538 mg CH₄/m²/day, respectively, in the fall of 1994, winter of 1994–1995, and summer of 1995. Median fluxes were 12.42, 8.62, and 5.65 mg CH₄/m²/day, respectively, during those seasons. Forty-three of 177 measurements had small negative fluxes, suggesting methanotrophic activity in the landfill cover soils. Despite probable methanotrophic activity in cover soils, landfills without gas collection systems may emit substantial CH₄ to the atmosphere, with large spatial and seasonal variability.     

Forecasting Air Pollution Potential: A Synoptic Climatological Approach

ABSTRACT

This paper describes the development and application of an air pollution potential (APP) forecast model based on a synoptic climatological approach in a heavily industrialized area in Durban, South Africa. The aim of the forecasting procedure, based on a system of orange, red, and all-clear alerts, was to give industry advance warning of periods of poor atmospheric dispersion so that it could take action to reduce emissions. The key meteorological parameter in accurately identifying the commencement of an APP episode was found to be negative surface pressure tendency. Wind direction was the most useful parameter in estimating the end point of an APP episode. The model was very successful in identifying periods of elevated SO₂, but there is a need for further refinement in forecasting the end point of an episode.