Cervical vertebral motions and biomechanical responses to direct loading of human head

There is little known data characterizing the biomechanical responses of the human head and neck under direct head loading conditions. However, the evaluation of the appropriateness of current crash test dummy head-neck systems is easily accomplished. Such an effort, using experimental means, generates and provides characterizations of human head-neck response to several direct head loading conditions. Low-level impact loads were applied to the head and face of volunteers and dummies. The resultant forces and moments at the occipital condyle were calculated. For the volunteers, activation of the neck musculature was determined using electromyography (EMG). In addition, cervical vertebral motions of the volunteers have been taken by means of X-ray cineradiography. The Ethics Committee of Tsukuba University approved the protocol of the experiments in advance. External force of about 210 N was applied to the head and face of five volunteers with an average age of 25 for the duration of 100 msec or so, via a strap at one of four locations in various directions: (1) an upward load applied to the chin, (2) a rearward load applied to the chin without facial mask, (3) a rearward load applied to the chin with the facial mask, and (4) a rearward load applied to the forehead. The same impact force as those for the human volunteers was also applied to HY-III, THOR, and BioRID. We found that cervical vertebral motions differ markedly according to the difference in impact loading condition. Some particular characteristics are also found, such as the flexion or extension of the upper cervical vertebrae (C0, C1, and C2) or middle cervical vertebrae (C3-C4), showing that the modes of cervical vertebral motions are markedly different among the different loading conditions. We also found that the biofidelity of dummies to neck response characteristics of the volunteers at the low-level impact loads is in the order of BioRID, THOR, and HY-III. It is relevant in this regard that the BioRID dummy was designed for a low-severity impact environment, whereas THOR and HY-III were optimized for higher-severity impacts.     

Re-copulation and post-copulatory mate guarding increase immediate female reproductive output in the dragonfly Nannophya pygmaea Rambur

After copulation, male Nannophya pygmaea dragonflies mate guard by hovering over ovipositing females and repelling conspecific males. Copulation is not always a prerequisite for oviposition in the females of this species because females can store the sperm received during previous visits/copulations. An oviposition episode consists of several bouts of oviposition separated by periods of perching. We conducted two types of male-removal experiments to examine the effects of mating and post-copulatory mate guarding on the oviposition behaviour of females. In the first experiment, we removed all males from the habitat to eliminate the effect of re-copulation, mate-guarding and harassment by males. In the second experiment, we removed males immediately after copulation to eliminate the effects of guarding and other post-copulatory male-female interactions. We compared these experimental data with data obtained under natural conditions. The dipping rate in an oviposition bout was not influenced by copulation or guarding. However, guarded females made more dips per episode than did solitary females. The proportion of time actually spent ovipositing (total bout duration/oviposition episode duration) of guarded females was higher than that of solitary females. Solitary females often oviposited in more than one territorial site, while guarded females usually oviposited within a single territorial site during an oviposition episode. Because males tend to hold territories at sites where egg survival is high, guarded females (and the male guardian) benefit from guarding in terms of egg hatchability. The possible benefits for solitary females are discussed.     

Voltammetric response of ferroceneboronic acid to diol and phenolic compounds as possible pollutants

A voltammetric determination of possible organic pollutants such as diol and phenolic compounds in water was studied using ferroceneboronic acid (FBA) as a redox-active marker. A cyclic voltammogram of FBA exhibited a pair of oxidation and reduction peaks at 230 and 170 mV at pH 7.0, respectively, while another pair of redox peaks was observed in the presence of diol or phenolic compounds tested. The results were rationalized based on the formation of boronate esters of FBA with the added compounds. The changes in the redox peak currents were dependent on the concentration of the additives, suggesting a usefulness of FBA in the electrochemical determination of these compounds in water.     

Study on dechlorination technology for municipal waste plastics containing polyvinyl chloride and polyethylene terephthalate

It is necessary to remove chlorine efficiently from municipal waste plastics (MWP) that contain polyvinyl chloride (PVC) and other plastics containing chlorine. In this article we consider thermal degradation liquefaction technology. In Japan, the chlorine content of reclamation oil products must be kept below 100 ppm owing to the quality standard for pyrolysis oil. Liquefaction dechlorination technology for MWP is still an important issue to study. The twin-screw extruder that has been developed as dechlorination technology for blast furnaces and coke ovens has a shorter residence time for dechlorination than other dechlorination technologies. In this article, we used a single-screw extruder for the dechlorination process because it also has a short residence time. Experiments on the dechlorination process were carried out by using a single-screw extruder to assess its dechlorination performance. Practical use of the single-screw was demonstrated by the operation of a commercial oil reclamation plant operated by Sapporo Plastic Recycle Co., Ltd. (SPR). Moreover, an investigation of cascade recycling was carried out in 2008 in which material recycle wastes were mixed with MWP and processed by chemical recycling (liquefaction). It was demonstrated that cascade recycling is an efficient recycling combination and contributes to local feedstock recycling. However, it was shown that MR wastes affect the quality of the reclamation oil when they make up more than 40% of the feed mix. If the quantity of MR wastes is kept below 40%, the reclamation oil is able to meet the quality standard. The SPR plant can be operated safely and in a stable manner.     

Point-of-use water disinfection using UV light-emitting diodes to reduce bacterial contamination

The treatment process described in this research explores the impact of exposing water samples containing fecal coliforms to the radiation produced by single ultraviolet (UV) light-emitting diodes (LEDs) operating at 265 nm. UV LEDs are long lasting, compact in size and produce more efficient light output than traditional mercury-vapour bulbs, making them ideal for application in point-of-use disinfection systems, such as in remote areas. In this study, contaminated water samples containing either a pure culture of Escherichia coli or tertiary effluent from the City of Regina Wastewater Treatment Plant were used to study the application and efficiency of using UV LEDs for water disinfection. The results indicate that bacterial inactivation was achieved in a time-dependent manner, with 1- and 2.5-log E. coli reductions in water following 20 and 50 min of UV LED exposure, respectively. Ultraviolet radiation was less effective in reducing coliform bacteria in wastewater samples due to the elevated turbidity levels. Further work remains to be completed to optimize the application of UV LEDs for point-of-use disinfection systems; however, the results from this study support that bacterial inactivation using UV LEDs is possible, meriting further future technological development of the LEDs.     

Systematic Biases in Measured PM10 Values with U.S. Environmental Protection Agency-Approved Samplers at Owens Lake,California

ABSTRACT

From 1993 through 1998, Wedding or Graseby high-volume PM₁₀ samplers were collocated with tapered element oscillating microbalance (TEOM) samplers at three sites at Owens Lake, CA. The study area is heavily impacted by windblown dust from the dry Owens Lake bed, which was exposed as a result of water diversions to the city of Los Angeles. A dichotomous (dichot) sampler and three collocated Partisol samplers were added in 1995 and 1999, respectively. U.S. Environmental Protection Agency (EPA) operating procedures were followed for all samplers, except for a Wedding sampler that was not cleaned for the purpose of this study. On average, the TEOM and Partisol samplers agreed to within 6%, and the dichot, Graseby, and Wedding samplers measured lower PM₁₀ concentrations by about 10, 25, and 35%, respectively. Surprisingly, the “clean” Wedding sampler consistently measured the same concentration as the “dirty” Wedding sampler through 85 runs without cleaning. The finding that the Graseby and Wedding high-volume PM₁₀ samplers read consistently lower than the TEOM, Partisol, and dichot samplers at Owens Lake is consistent with PM₁₀ sampler comparisons done in other fugitive dust areas, and with wind tunnel tests showing that sampler cut points can be significantly lower than 10 um under certain conditions. However, these results are opposite of the bias found for TEOM samplers in areas that have significant amounts of volatile particles, where the TEOM reads low due to the vaporization of particles on the TEOM's heated filter. Coarse particles like fugitive dust are relatively unaffected by the filter temperature. This study shows that in the absence of volatile particles and in the presence of fugitive dust, a different systematic bias of up to 35% exists between samplers using dichot inlets and high-volume samplers, which may cause the Graseby and Wedding PM₁₀ samplers to undermeasure PM₁₀ by up to 35% when the PM₁₀ is predominantly from coarse particulate sources.     

Improvement of driver active interventions during automated driving by displaying trajectory pointers—A driving simulator study

Abstract

Objective: The handover of vehicle control from automated to manual operation is a critical aspect of interaction between drivers and automated driving systems (ADS). In some cases, it is possible that the ADS may fail to detect an object. In this event, the driver must be aware of the situation and resume control of the vehicle without assistance from the system. Consequently, the driver must fulfill the following 2 main roles while driving: (1) monitor the vehicle trajectory and surrounding traffic environment and (2) actively take over vehicle control if the driver identifies a potential issue along the trajectory. An effective human–machine interface (HMI) is required that enables the driver to fulfill these roles. This article proposes an HMI that constantly indicates the future position of the vehicle.

Methods: This research used the Toyota Dynamic Driving Simulator to evaluate the effect of the proposed HMI and compares the proposed HMI with an HMI that notifies the driver when the vehicle trajectory changes. A total of 48 test subjects were divided into 2 groups of 24: One group used the HMI that constantly indicated the future position of the vehicle and the other group used the HMI that provided information when the vehicle trajectory changed.

The following instructions were given to the test subjects: (1) to not hold the steering wheel and to allow the vehicle to drive itself, (2) to constantly monitor the surrounding traffic environment because the functions of the ADS are limited, and (3) to take over driving if necessary.

The driving simulator experiments were composed of an initial 10-min acclimatization period and a 10-min evaluation period. Approximately 10?min after the start of the evaluation period, a scenario occurred in which the ADS failed to detect an object on the vehicle trajectory, potentially resulting in a collision if the driver did not actively take over control and manually avoid the object.

Results: The collision avoidance rate of the HMI that constantly indicated the future position of the vehicle was higher than that of the HMI that notified the driver of trajectory changes, χ² = 6.38, P < .05. The steering wheel hands-on and steering override timings were also faster with the proposed HMI (t test; P < .05).

Conclusions: This research confirmed that constantly indicating the position of the vehicle several seconds in the future facilitates active driver intervention when an ADS is in operation.     

Influence of oxygen flow rate and compost addition on reduction of organic matter in aerated waste layer containing mainly incineration residue

Landfilling municipal solid waste incineration (MSWI) residue alkalizes the waste layer, causing a subsequent decrease in microbial activity and a delay in the decomposition of organic matter. In this study, efficiencies of neutralization of the leachate and organic matter decomposition in the waste layer in a column filled with MSWI residue using aeration and compost addition were evaluated.Total organic carbon (TOC) reduction in the waste layer is large at high oxygen flow rate (OFR). To effectively accelerate TOC reduction in the waste layer to which compost was added, a high OFR exceeding that by natural ventilation was required. At day 65, the pH of the leachate when OFR was above 102mol-O2/(day·m3) was lower than that when OFR was below 101mol-O2/(day·m3). At the same OFR, the pH of waste sample was lower than that of waste sample with compost. Although leachate neutralization could be affected by compost addition, TOC reduction in the waste layer became rather small. It is possible that humic substances in compost prevent the decomposition of TOC in MSWI residue.     

Spider silk has an ice nucleation activity

Several ice nucleating substances have been identified, which exist in vivo or can be extracted from biological materials. Spider silk, which has a strong ability for water condensation, has also been found to possess an ice nucleation activity. The freezing temperature of water droplets was higher in the presence than in the absence of spider silk. Moreover, by means of environmental scanning electron microscopy, it was observed that the activity is not due to foreign matter attached to the silk but to the silk fibroin itself.     

Maternal transfer of organochlorine pesticides, polychlorinated dibenzo-p-dioxins, dibenzofurans, and coplanar polychlorinated biphenyls in frogs to their eggs

Previous study confirmed that there were sexual differences in concentrations of organochlorine pesticides and dioxins in frogs during the breeding season. The present study utilized the egg masses from the previous study to determine the cause(s) of the sexual differences. When concentrations of the detected chemicals were compared between the female frogs and their eggs, it was found that the concentrations in the eggs were several times those in their mothers. The results indicated that maternal transfer reduced tissue concentrations in females. Since the weight of each egg mass was half that of the mother, two-thirds of the chemicals in a female frog were transferred to its eggs. In addition, the degree of maternal transfer differed among compounds. Maternal transfer of PCDDs and PCDFs with four or five chlorine atoms and coplanar PCBs followed the fugacity model. However, maternal transfer decreased for PCDDs/DFs with six or more chlorines as the octanol-water partition coefficient increased. From these results, maternal transfer was confirmed as the cause of sexual differences in concentrations of organochlorine pesticides and dioxins in adult frogs during the breeding season.