Multiresidue determination of carbamate,organochlorine, organophosphorus,and dicarboximide pesticides in lettuce by GC/MS

An extraction method based on matrix solid-phase dispersion was developed to determine pirimicarb, methyl parathion, malathion, procymidone, α -endosulfan and β -endosulfan in lettuce using gas chromatography-mass spectrometry. The best results were obtained using 4.0 g of lettuce, 2.0 g of silica as dispersant sorbent, 0.1 g of activated carbon as clean up sorbent and acetonitrile as eluting solvent. The method was validated using lettuce samples fortified with pesticides at six different concentration levels (0.1 to 2.0 mg/kg). Average recoveries (7 replicates) ranged from 50 to 120 %, with relative standard deviations between 0.6 and 8.0 %. Detection and quantification limits for lettuce ranged from 0.01 to 0.02 mg/kg and 0.04 to 0.10 mg/kg, respectively.     

Field dissipation of oxyfluorfen in onion and its dynamics in soil under Indian tropical conditions

Oxyfluorfen, a diphenyl-ether herbicide is being used to control annual and perennial broad-leaved weeds and sedges in a variety of field crops including onion. The present study was aimed to investigate the dynamics and field persistence of oxyfluorfen in onion plant, bulb and soil under Indian tropical conditions. Application of four rates of oxyfluorfen viz., 200, 250, 300 and 400 g AI ha^?1 as pre-emergence gave good weed control in field experiment with onion. The oxyfluorfen residue dissipated faster in plant than in soil respectively, with a mean half-life of 6.1 and 11.2 days. Dissipation followed first-order kinetics. In laboratory column leaching experiments, 17 percent of the applied oxyfluorfen was recovered from the soil and indicates its solubility in water and mobility in sandy clay loam soil was low. A sorption study revealed that the adsorption of oxyfluorfen to the soil was highly influenced by the soil organic carbon with the K_oc value of 5450. The study concludes that the dissipation of oxyfluorfen in soil and onion was dependent on the physico-chemical properties of the soil and environmental conditions.     

Numerical Simulation of the Thermal Destruction of Some Chlorinated C1 and C2 Hydrocarbons

We have numerically modeled the breakdown of small quantities of several chlorinated hydrocarbons (CH₃CI, CH₂CI₂, CHCI₃, CCI₄, C₂H₃CI, and C₂H₅CI) in a lean mixture of combustion products between 800 and 1480 K. This simulates the fate of poorly atomized waste in a liquid-Injection Incinerator. Kinetics calculations were performed using the CHEMKIN and SENKIN programs, with a reaction mechanism that was developed at Louisiana State University to model flat-flame burner experiments.

A 99.99-percent destruction efficiency was attained In one second at temperatures ranging from 1280 to 960 K, with CCI4 requiring the highest temperature for destruction and C₂H₅CI the lowest. For all compounds except C₂H₅CI, there was a range of temperatures at which byproducts accounted for several percent of the elemental chlorine at the outlet. The more heavily chlorinated compounds formed more byproducts even though the amount of elemental chlorine was the same in all cases. The sensitivity of results to residence time, equivalence ratio, temperature profile, and the presence of additional chlorine, was examined for the case of CHCI₃.     

Assessment of Needs for Technical Information in EPA’s Hazardous and Solid Waste Programs

Headquarters managers and Regional staff in the U.S. Environmental Protection Agency’s hazardous and solid waste programs were surveyed to determine priorities for technical information and guidance among EPA Regional staff, state hazardous waste management staff, EPA contractors, and the regulated community. The survey also examined delivery systems effective for EPA Regional staff. The fifteen highest ranked technical needs for RCRA, Superfund, and UST reflect a pervasive interest in hazardous waste remediation. Top priority technical needs focus on establishing cleanup levels, subsurface fate and transport, field monitoring and quality assurance, remedy selection, and most importantly, which remedies work and which do not in specific situations. Technical needs of non- EPA audiences are quite similar to those for EPA field staff. Preferences for technology transfer delivery systems are generally for conventional distribution methods (such as print materials and workshops) rather than electronic or video media. Regional staff report serious problems in utilizing technology transfer because of time constraints, insufficient knowledge of available products, insufficient travel funds, and limited access to and training on computers.     

Measurement of Volatile Organics at Part per Billion Concentrations Using a Cold Trap Inlet and High Speed Gas Chromatography

Direct inlet gas chromatography (GC) is becoming one of the most frequently used techniques for measurement of volatile organics in air. Although GC is an effective tool, its usefulness as a field method can be limited by retention times of several minutes or more, and by the limits of detection. In order to address these issues, a high speed GC system featuring a capillary cold trap inlet and variable speed electrometeramplifier was developed and tested.

The gas cooled inlet was used to collect and focus organic vapors from injection volumes of up to 1 ml. Resistance heating of the metal cold trap produced a narrow injection band that allowed simple separations to be completed in 5 to 20 seconds. Use of a variable speed electrometer-amplifier allowed the response time and noise suppression characteristics to be adjusted to the needs of the specific analysis.

Simple mixtures of organics including aromatics, alkanes and chlorinated hydrocarbons were separated in 20 seconds or less. The limits of detection for 13 test compounds ranged from less than 1 part per billion by volume (ppbv) to about 50 ppbv. Data presented here indicate that high speed GC using a cold trap inlet may be a feasible approach for near real-time measurement of volatile organics in ambient air.     

An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

Ozone and Other Air Quality-Related Variables Affecting Visibility in the Southeast United States

Abstract

An analysis of ozone (O₃) concentrations and several other air quality-related variables was performed to elucidate their relationship with visibility at five urban and semi-urban locations in the southeast United States during the summer seasons of 1980-1996. The role and impact of O₃ on aerosols was investigated to ascertain a relationship with visibility. Regional trend analysis over the 1980s reveals an increase in maximum O₃ concentration coupled with a decrease in visibility. However, a similar analysis for the 1990s shows a leveling-off of both O₃ and visibility; in both cases, the results were not statistically significant at the 5% level. A case study of site-specific trends at Nashville, TN, followed similar trends. To better understand the relationships between O₃ concentration and visibility, the analysis was varied from yearly through daily to hourly averaged values. This increased temporal resolution showed a statistically significant inverse relationship between visibility and O₃. Site-specific hourly r² values ranged from 0.02 to 0.43. Additionally, by performing back-trajectory analysis, it was found that the visibility degraded by air mass migration over polluted areas.     

The Steubenville Comprehensive Air Monitoring Program (SCAMP): Overview and Statistical Considerations

Abstract

Average concentrations of particulate matter with an aerodynamic diameter less than or equal to 2.5 μm (PM_2.5) in Steubenville, OH, have decreased by more than 10 μg/m³ since the landmark Harvard Six Cities Study¹ associated the city’s elevated PM_2.5 concentrations with adverse health effects in the 1980s. Given the promulgation of a new National Ambient Air Quality Standard (NAAQS) for PM_2.5 in 1997, a current assessment of PM_2.5 in the Steubenville region is warranted. The Steubenville Comprehensive Air Monitoring Program (SCAMP) was conducted from 2000 through 2002 to provide such an assessment. The program included both an outdoor ambient air monitoring component and an indoor and personal air sampling component. This paper, which is the first in a series of four that will present results from the outdoor portion of SCAMP, provides an overview of the outdoor ambient air monitoring program and addresses statistical issues, most notably autocorrelation, that have been overlooked by many PM_2.5 data analyses. The average PM_2.5 concentration measured in Steubenville during SCAMP (18.4 μg/m³) was 3.4g/m³ above the annual PM_2.5 NAAQS. On average, sulfate and organic material accounted for ～31% and 25%, respectively, of the total PM_2.5 mass. Local sources contributed an estimated 4.6 μg/m³ to Steubenville’s mean PM_2.5 concentration. PM_2.5 and each of its major ionic components were significantly correlated in space across all pairs of monitoring sites in the region, suggesting the influence of meteorology and long-range transport on regional PM_2.5 concentrations. Statistically significant autocorrelation was observed among time series of PM_2.5 and component data collected at daily and 1-in-4-day frequencies during SCAMP. Results of spatial analyses that accounted for autocorrelation were generally consistent with findings from previous studies that did not consider autocorrelation; however, these analyses also indicated that failure to account for autocorrelation can lead to incorrect conclusions about statistical significance.     

A New Tape Reagent for the Determination of Hydrogen Sulfide in Air

The lead acetate paper tape reagent method for the estimation of hydrogen sulfide in air has been reviewed with the conclusions that the colored spots on which the quantitative estimation is based are not stable and do not lend by themselves to accurate results. Although it may be retained for grab sampling work, the lead acetate paper tape reagent is not acceptable as a stoichiometric reagent in any case where long duration sampling periods are concerned like in air pollution studies. A new mercuric chloride paper tape reagent has been developed as a substitute. Due to the fact that the colored spots resulting from the action of hydrogen sulfide on mercuric chloride are sensitive and very stablet, this new paper tape reagent is proposed as an adequate and reliable analytical too for the estimation of hydrogen sulfide in air. Also, a more comprehensive application of the paper tape analytical system is proposed throughout a suitable control of the factor tape retention capacity vs sampling rate which imposes some restrictions in the selection of the practical working range of concentrations. Nevertheless this working range is still wide enough to encompass all the hydrogen sulfide concentrations normally encountered in the city atmosphere.     

Fuel Oil Additives for Controlling Air Contaminant Emissions

An addition of additives to fuel oils prior to combustion is one way of reducing combustible contaminant emissions to the outer air. Reported test results show that some additives improve, moderately, the combustive properties of fuel oils. Combustion is also improved but to a lesser degree, in boiler systems that are deficient in operation and design. Being combustible, polynuclear hydrocarbons emissions would be reduced by use of additives. Other types of additives to reduce slagging and inhibit corrosion from combustion of fuel oils are also available. The cost of using additives is low. Improved additives are required, especially ones to better combustion in the deficient boiler systems. These can be found by research and literature surveys. Their effectiveness and nontoxicity would be confirmed by laboratory and field testing.