PVD coated mill rolls for cold rolling of stainless steel strips—Tribological and mechanical laboratory tests

The cost of rolling is determined in particular by productivity and lifetime of rolls before regrinding. Adhesive wear of the sheet gives rise to transfer on the roll surface. Its occurrence depends on rolling conditions and is one of the determining factors of the maximal reduction for a given rolling speed. Abrasive wear of the roll is the second factor for roll lifetime. Both phenomena are strongly related to tribological and mechanical characteristics of the surface layer of rolls. Stainless steel is known for its high adhesiveness. Coatings with good tribological properties could help extend the roll service. In this paper, the potential of different PVD coatings (CrN, TiN and TiBN) is explored. The impact of these coatings on influential phenomena during rolling is analyzed thanks to well-adapted tribological and mechanical laboratory tests. The results show that TiN has a good potential in cold rolling of stainless steel strips.     

Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy

Tool life has been a vital issue in machining titanium alloys. Recently, an atomization-based cutting fluid (ACF) application has been found to be an effective approach for cooling and lubrication in micromachining operations. In this study, an ACF spray system is developed for macro-scale turning of Ti–6Al–4V. The spray system is designed to minimize interaction between the fluid droplets, and the gas nozzle to control the divergence of the fluid droplets. Experiments are conducted to study the effect of five specific ACF spray parameters including fluid flow rate, spray distance, impingement angle, and type and pressure level of the droplet carrier gas on cutting forces, tool life, and chip characteristics. It has been observed that the combination of lower pressure (150 psi) air-mixed CO₂ with a higher flow rate (20 ml/min) and a larger spray distance (35 mm) produces a significantly longer tool life and broken chips. The results also reveal that the ACF spray system can extend tool life up to 40–50% over flood cooling.     

Modeling and interpretation of fiber orientation-based failure mechanisms in machining of carbon fiber-reinforced polymer composites

The development and implementation of a microstructure-based finite element model for the machining of carbon fiber-reinforced polymer composites is presented. A new approach to interfacial modeling is introduced where the material interface is modeled using continuum elements, allowing failure to take place in either tension or compression. The model is capable of describing the fiber failure mode occurring throughout the chip formation process. Characteristic fiber length in the chips, and machining forces for microstructures with fibers orientated at 0°, 45°, 90°, and 135° are examined. For model validation purposes, the model-based machining performance predictions are compared to the machining responses from a set of orthogonal machining experiments. A parametric study is presented that identifies a robust tool geometry, which minimizes the effects of fiber orientation and size on the machining forces.     

The double trade-off between adaptation and mitigation for sea level rise: an application of FUND

This paper studies the effects of adaptation and mitigation on the impacts of sea level rise. Without adaptation, the impact of sea level rise would be substantial, almost wiping out entire countries by 2100, although the globally aggregate effect is much smaller. Adaptation would reduce potential impacts by a factor 10–100. Adaptation would come at a minor cost compared to the damage avoided. As adaptation depends on socio-economic status, the rank order of most vulnerable countries is different than the rank order of most exposed countries. Because the momentum of sea level rise is so large, mitigation can reduce impacts only to a limited extent. Stabilising carbon dioxide concentrations at 550 ppm would cut impacts in 2100 by about 10%. However, the costs of emission reduction lower the avoided impacts by up to 25% (average 10%). This is partly due to the reduced availability of resources for adaptation, and partly due to the increased sensitivity to wetland loss by adaptation.

Anatomical localization and stereoisomeric composition of <Emphasis Type="Italic">Tribolium castaneum</Emphasis> aggregation pheromones

We report that the abdominal epidermis and associated tissues are the predominant sources of male-produced pheromones in the red flour beetle, Tribolium castaneum and, for the first time, describe the stereoisomeric composition of the natural blend of isomers of the aggregation pheromone 4,8-dimethyldecanal (DMD) in this important pest species. Quantitative analyses via gas chromatography–mass spectrometry showed that the average amount of DMD released daily by single feeding males of T. castaneum was 878 ± 72 ng (SE). Analysis of different body parts identified the abdominal epidermis as the major source of aggregation pheromone; the thorax was a minor source, while no DMD was detectable in the head. No internal organs or obvious male-specific glands were associated with pheromone deposition. Complete separation of all four stereoisomers of DMD was achieved following oxidation to the corresponding acid, derivatization with (1R, 2R)- and (1S, 2S)-2-(anthracene-2,3-dicarboximido)cyclohexanol to diastereomeric esters, and their separation on reversed-phase high-performance liquid chromatography at −54°C. Analysis of the hexane eluate from Porapak-Q-collected volatiles from feeding males revealed the presence of all four isomers (4R,8R)/(4R,8S)/(4S,8R)/(4S,8S) at a ratio of approximately 4:4:1:1. A walking orientation bioassay in a wind tunnel with various blends of the four synthetic isomers further indicated that the attractive potency of the reconstituted natural blend of 4:4:1:1 was equivalent to that of the natural pheromone and greater than that of the 1:1 blend of (4R,8R)/(4R,8S) used in commercial lures.     

The response of a mid- and high latitude peat bog to predicted climate change: methane production in a 12-month peat incubation

There are fears that global warming will lead to degradation of peatlands, higher emissions of greenhouse gases from peat, and accelerated warming. Anaerobic decomposition of organic soils produces methane (CH₄), a potent greenhouse gas. Two peat bogs differing in mean annual temperature, Velke Darko (VD, Czech Republic, 7.2 °C), and Stor Åmyran (SA, Sweden, 4.0 °C), were selected for a comparative study of how organic soils in different climatic zones will respond to warmer and drier conditions. Twenty peat cores from each bog were incubated in growth chambers. Under present-day summer conditions, VD produced 14 times more CH₄ than SA. Two different warming scenarios were used. Peat-core replicates were kept at temperatures of 11 versus 16 °C, and 11 versus 22 °C. From 11 to 16 °C, the CH₄ production slightly decreased at SA, and slightly increased at VD. From 11 to 22 °C, the CH₄ production increased 9 times at SA, but slightly decreased at VD. After an 8-month incubation, peat cores under drying conditions (water table at ?14 cm) were compared to samples with original water table (?2 cm). Drying conditions led to a steeper reduction in CH₄ production at VD, compared to SA. The CH₄ production decreased more than 100 times at VD. Then, the combined effect of simultaneous warming and drying at 11 and 22 °C was studied. We did not find any significant effect of interactions between increasing temperature and decreasing water table level. Overall, the warmer site VD responded more strongly to the simulated climate change than the colder site SA.     

Molecular Detection of human Noroviruses in Influent and Effluent Samples From Two Biological Sewage Treatment Plants in the Region of Monastir,Tunisia

Noroviruses (NoVs) are responsible for numerous cases of waterborne and foodborne gastroenteritis every year. They are released in the sewage and their detection in this environment can reflect the epidemiology of the viral strains circulating in the community. A three-year (2007–2010) survey was conducted in order to evaluate the presence of human NoVs using RT-PCR in 518 sewage samples collected at the entrance and exit of two biological sewage treatment plants located in Monastir region, Tunisia. In this study, we aimed to genetically characterize the most prevalent GI and GII NoV strains, in order to obtain a rough estimate of the efficacy of disinfection treatments and to compare the results with clinical data documented in the same area during the same period. This work confirms the wide circulation and the genetic diversity of NoVs in Tunisia and the widespread distribution of NoV variants in both raw and treated wastewater. Indeed, NoV was detected in 192 (37.1 %) sewage samples, among them mixed infections with group A rotavirus were detected in 125 (65.1 %) cases. The genotypes of the GI NoVs were GI.1, GI.2, GI.4, GI.5, and GI of unassigned genotype (GI.UA), and the genotypes of the GII NoVs were all GII.12. This study enhances the currently poor environmental virological data gathered in Tunisia, demonstrates the benefit of environmental surveillance as a tool to determine the epidemiology of NoVs circulating in a given community, and underlines the need for the design and support of similar long-term studies in our country, in order to compensate for the absence of a national surveillance system for gastroenteric viruses.     

Mapping Adolescents’ Sense of Place and Perceptions of Change in an Urban–Rural Transition Area

Environmental Management - Landscapes are changing, with rural areas becoming increasingly urbanized. Children and adolescents are underrepresented in the sense-of-place literature. Our study aimed...     

Circumpolar status of Arctic ptarmigan: Population dynamics and trends

Rock ptarmigan (Lagopus muta) and willow ptarmigan (L. lagopus) are Arctic birds with a circumpolar distribution but there is limited knowledge about their status and trends across their circumpolar distribution. Here, we compiled information from 90 ptarmigan study sites from 7 Arctic countries, where almost half of the sites are still monitored. Rock ptarmigan showed an overall negative trend on Iceland and Greenland, while Svalbard and Newfoundland had positive trends, and no significant trends in Alaska. For willow ptarmigan, there was a negative trend in mid-Sweden and eastern Russia, while northern Fennoscandia, North America and Newfoundland had no significant trends. Both species displayed some periods with population cycles (short 3–6 years and long 9–12 years), but cyclicity changed through time for both species. We propose that simple, cost-efficient systematic surveys that capture the main feature of ptarmigan population dynamics can form the basis for citizen science efforts in order to fill knowledge gaps for the many regions that lack systematic ptarmigan monitoring programs.