Estimation of pollutant partition in sandy soils with different water contents

The objectives of this work were: (1) to identify an isotherm model to relate the contaminant contents in the gas phase with those in the solid and non-aqueous liquid phases; (2) to develop a methodology for the estimation of the contaminant distribution in the different phases of the soil; and (3) to evaluate the influence of soil water content on the contaminant distribution in soil. For sandy soils with negligible contents of clay and natural organic matter, contaminated with benzene, toluene, ethylbenzene, xylene, trichloroethylene (TCE), and perchloroethylene (PCE), it was concluded that: (1) Freundlich’s model showed to be adequate to relate the contaminant contents in the gas phase with those in the solid and non-aqueous liquid phases; (2) the distribution of the contaminants in the different phases present in the soil could be estimated with differences lower than 10% for 83% of the cases; and (3) an increase of the soil water content led to a decrease of the amount of contaminant in the solid and non-aqueous liquid phases, increasing the amount in the other phases.     

N-nitrosodimethylamine and trihalomethane formation and minimisation in Southeast Queensland drinking water

This study assesses the prevalence of disinfection by-product (DBP) precursors in some Southeast Queensland drinking water sources by conducting formation potential experiments for the four regulated trihalomethanes (THMs), and the potent carcinogen, N-nitrosodimethylamine (NDMA). NDMA formation potentials were consistently low (<5-21 ng/L), and total THM (tTHM) formation potentials were consistently below the Australian Drinking Water Guideline (250 μg/L). NDMA concentration of finished drinking waters was also monitored and found to be <5 ng/L in all cases. The effect of coagulation and advanced oxidation on the formation of NDMA and THMs is also reported. UV/H(2)O(2) pre-treatment was effective in producing water with very low THMs concentrations, and UV irradiation was an effective method for NDMA degradation. H(2)O(2) was not required for the observed NDMA degradation to occur. Coagulation using alum, ferric chloride or poly(diallyldimethylammonium chloride) (polyDADMAC) was ineffective in removing DBPs precursors from the source water studied, irrespective of the low dissolved organic carbon (DOC) and dissolved organic nitrogen (DON) attained. Rather, coagulation with polyDADMAC caused an increase in NDMA formation potential upon chloramination, and all coagulants led to an increased tTHM formation potential upon chlorination due to the high bromide concentration of the source water studied.     

Chlorinated and brominated dibenzo-p-dioxins and dibenzofurans in surface sediment from Taihu Lake, China

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) in surface sediment samples from Taihu Lake--an important water supply of the Yangtze River Delta, China--were investigated in the present study. Concentrations of PCDD/Fs ranged from 0.91 to 4.8 pg TEQ g(-1) dw (mean: 2.9 pg TEQ g(-1) dw, TEQ: Toxic Equivalent), which were all higher than the threshold effect level established by interim sediment quality guidelines in Canada (0.85 pg TEQ g(-1) dw). The levels of PBDD/Fs ranged from 0.16 to 1.6 pg TEQ g(-1) dw (mean: 0.52 pg TEQ g(-1) dw) and accounted for 5-33% (mean: 14%) of the total PCDD/Fs and PBDD/Fs TEQ. Comparatively, the abundance of sedimentary PCDD/Fs in the three regions (Meiliang Bay, Gonghu Bay, and Xukou Bay) showed a decreasing trend from the inflow region to the outflow region, while no significant difference was observed among their 2,3,7,8-PBDD/Fs levels, which suggested that the sources of PCDD/Fs and PBDD/Fs differed in this area. Principal component analysis suggested that the historical production/usage of pentachlorophenol and sodium pentachlorophenate was the dominant source of PCDD/Fs in the sediment of these regions. Although the specific sources of PBDD/Fs in the sediment of Taihu Lake were unclear, it was suspected to be due to atmospheric deposition; however, an additional study is needed to confirm this.     

Concentrations of organophosphate esters and brominated flame retardants in German indoor dust samples

While it is known that the ingestion of indoor dust contributes substantially to human exposure to the recently restricted polybrominated diphenyl ethers (PBDEs), the situation for one class of potential replacements, i.e. organophosphate esters (OPEs), used in a variety of applications including as flame retardants has yet to be fully characterised. In this study, surface dust from twelve different cars from various locations throughout Germany were analysed for eight OPEs, decabromodiphenyl ethane (DBDPE), and eight PBDEs. In five cars, tris-(1,3-dichloro-2-propyl) phosphate (TDCPP) was the dominant compound with concentrations up to 620 μg g(-1) dust. High concentrations of tri-cresyl phosphate (TCP) (up to 150 μg g(-1)) were also detected in two samples of car dust. Dust from ten offices in the same building in Ludwigsburg, Germany was also analysed. In these samples, tri (2-butoxyethyl) phosphate (TBEP) predominated with an average concentration of 7.0 μg g(-1) dust, followed by tris (1-chloro-2-propyl) phosphate (TCPP) at 3.0 μg g(-1) and triphenyl phosphate (TPhP) at 2.5 μg g(-1) dust. Although caution must be exercised given the relatively small database reported here; this study provides evidence that cars and offices from Germany are significantly more contaminated with OPEs than PBDEs. Average concentrations of ΣOPEs were ten times higher in car than in office dust. This is the first study to provide data on a wide range of OPE concentrations in German indoor dust samples.     

A methodology to identify representative configurations of sensors for monitoring soil moisture

Soil moisture is the key link among hydroecological compartments, responding dynamically to sequences of atmospheric processes and management conditions and modulating physical, chemical, and biological processes in the soil. Currently, there are a variety of monitoring techniques to measure, directly or indirectly, the soil moisture. However, some practical issues remain open like the definition a priori of the number, location and depth of the monitoring points, and the impact of failing or poor performance soil moisture sensors. Here, we present a set of techniques, namely Δθ time series, wavelet filtering, and time stability, to identify representative points and monitoring depths through an analysis of hourly soil moisture time series for different configuration of the monitoring network. We used real data from a monitoring network consisting of seven monitoring points, each one with four EC-5 probes (Decagon Devices Inc., Pullman, WA) at 20, 40, 60, and 100?cm. The use of simple time series of Δθ allowed us to assess the spatiotemporal influence of the monitoring points, while the wavelet periodograms allowed us to get insight about the response of the monitoring points at different time scales. Both methods are easy to implement or adapt to specific conditions, being coherent to the results derived from time stability analysis. For our case study, we concluded that we could reallocate 16 sensors (out of 28) without a significant loss of information. However, the final decision strongly relies on a deep knowledge of the site features and the objectives of the monitoring network.     

Fast simultaneous determination of traces of Cu(II) and Co(II) in soils and sediments with the luminol/perborate chemiluminescent system

A flow injection analysis method based on ion chromatography and luminol chemiluminescence detection was used for the simultaneous determination of copper (II) and cobalt (II) trace levels in soils and sediments following microwave-assisted acid digestion. Detection was based on chemiluminescence (CL) of the luminol–perborate system in an alkaline medium, which is catalyzed by both transition metals. The concentration and pH of the eluent (oxalic acid) was found to affect CL intensities and retention times, both of which were inversely proportional to the oxalic acid concentration. The calibration curves for both metal ions were linear and allowed a limit of detection of 0.003 μg l^?1 for cobalt (II) and 0.014 μg l^?1 for cooper (II) to be calculated. The proposed method was successfully used to determine both metal ions in certified reference materials of stream and river sediments and soil samples. Based on the results, the determination is free of interferences from the usual concomitant ions.     

Rate of occurrence of failures based on a nonhomogeneous Poisson process: an ozone analyzer case study

Atmospheric pollutant monitoring constitutes a primordial activity in public policies concerning air quality. In São Paulo State, Brazil, the São Paulo State Environment Company (CETESB) maintains an automatic network which continuously monitors CO, SO₂, NO _x , O₃, and particulate matter concentrations in the air. The monitoring process accuracy is a fundamental condition for the actions to be taken by CETESB. As one of the support systems, a preventive maintenance program for the different analyzers used is part of the data quality strategy. Knowledge of the behavior of analyzer failure times could help optimize the program. To achieve this goal, the failure times of an ozone analyzer—considered a repairable system—were modeled by means of the nonhomogeneous Poisson process. The rate of occurrence of failures (ROCOF) was estimated for the intervals 0–70,800 h and 0–88,320 h, in which six and seven failures were observed, respectively. The results showed that the ROCOF estimate is influenced by the choice of the observation period, t ₀?=?70,800 h and t ₇?=?88,320 h in the cases analyzed. Identification of preventive maintenance actions, mainly when parts replacement occurs in the last interval of observation, is highlighted, justifying the alteration in the behavior of the inter-arrival times. The performance of a follow-up on each analyzer is recommended in order to record the impact of the performed preventive maintenance program on the enhancement of its useful life.     

Assessment of potential health risk for inhabitants living near a former lead smelter. Part 1: metal concentrations in soils, agricultural crops, and homegrown vegetables

Soil contamination by metals engenders important environmental and health problems in northern France where a smelter (Metaleurop Nord) was in activity for more than a century. This study aims to look at the long-term effects of the smelter after its closedown by combining data on the degree of soil contamination and the quality of the crops grown (agricultural crops and homegrown vegetables) in these soils for a better assessment of the local population’s exposure to Cd, Pb, and Zn. Seven years after the Metaleurop Nord closedown, (1) the agricultural and urban topsoils were strongly contaminated by Cd, Pb, and Zn; (2) the kitchen garden topsoils were even more polluted than the agricultural soils, with great variability in metal concentrations within the gardens studied; (3) a high proportion of the agricultural crops for foodstuffs did not conform with the European legislation; (4) for feedstuffs, most samples did not exceed the Cd and Pb legislation limits, indicating that feedstuffs may be an opportunity for most agricultural produce; and (5) a high proportion of the vegetables produced in the kitchen gardens did not conform with the European foodstuff legislation. The high contamination level of the soils studied continues to be a risk for the environment and the population’s health. A further investigation (part 2) assesses the associated potential health risk for local inhabitants through consumption of homegrown vegetables and ingestion of soil particles by estimating the site-specific human health assessment criteria for Cd and Pb.