Combustion characteristics of Malaysian municipal solid waste and predictions of air flow in a rotary kiln incinerator

Malaysia is in dire need of alternatives to landfilling for solid waste management. Recently, landfills have faced the problems of overfilling, overflowing of leachates leading to pollution of water resources, and uncontrolled dust emissions adversely affecting the local environment. With the rising cost of urbanization coupled with the high rate of waste generation, one possible method of waste treatment that is receiving particular attention by the government is incineration. Incineration of solid waste is rather new in Malaysia, with limited usage in handling small sources of waste generation such as the municipal solid waste (MSW) of resort islands; however, its potential in ameliorating the problems associated with solid waste treatment may make it an attractive alternative to landfill. This article presents the results of test runs conducted to investigate the performance of a locally designed and manufactured rotary kiln incinerator (RKI). The test runs were conducted using MSW collected from the Shah Alam municipality. The combustion efficiency was analyzed by looking at the temperature profiles and chemical species concentrations. To complement the combustion characteristics measurements, predictions of the air flow in the incinerator during the process were also investigated. The overall performance of the RKI suggests that it is suitable for treating MSW.     

Processing and Properties of Mixtures of PHB-V with Post-consumer LDPE

Mixtures of poly-β-(hydroxybutyrate-co-valerate) PHB-V with virgin and post-consumer low density polyethylene (LDPE) were prepared by melt mixing in proportions of 100/0, 90/10, 80/20, 70/30 and 0/100 (wt/wt%). The mixtures were analysed by infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), melting flow index (MFI), tensile tests, scanning electron microscopy (SEM) and biodegradation in simulated soil. The DMTA and DSC curves of post-consumer LDPE suggested that this polymer was a mixture of LDPE and linear low density polyethylene (LLDPE). Virgin and post-consumer LDPE had lower MFI than PHB-V, but the blends showed higher index as the content of LDPE increased. The addition of LDPE reduced the tensile strength and Young’s modulus of the mixtures compared with PHB-V. SEM indicated poor interfacial adhesion between PHB-V and LDPE. PHB-V degraded slow and gradually, while both LDPE showed virtually no degradation under the conditions studied. The biodegradability of the blends depended on their composition and of the type of LDPE. LDPE improved the biodegradability of the mixtures.     

Influence of Technological Process on Biodegradation of PVA/Waxy Starch Blends in an Aerobic and Anaerobic Environment

Improving biodegradability of PVA/starch blends is a reality already documented by a number of works. Admittedly, mechanical properties of products (for example, tensile strength) are somewhat worse, but suitable composition optimizing or chemical modifying of starch may eliminate the problem to a large degree. This work is an attempt to find another potential effect influencing biodegradability, that of technological procedure for producing films from these blends on an extruder. The procedure with a so-called pre-extrusion step (two-stage) and dry-blend (single-stage) produced blends of slightest differences in achieved biodegradability (virtually within limits of experimental error) in aerobic (76 vs. 79%) as well as anaerobic breakdown (48 vs. 52%). Conversely, morphological analysis exhibited superior homogeneity of films prepared by the two-stage process; their tensile strength was also higher.     

Relationships between street characteristics and perceived attractiveness for walking reported by elderly people

Walking is important for the health of elderly people. Previous studies have found a relationship between neighbourhood characteristics, physical activity and related health aspects. The multivariate linear regression model presented here describes the relationships between the perceived attractiveness of streets for walking along and (physical) street characteristics. Two hundred and eighty-eight independently living elderly people (between 55 and 80 years old) participated in the study. Street characteristics were assessed along homogeneous street subsections defined as ‘links’. Positively related to perceived attractiveness of links were the following street characteristics: slopes and/or stairs, zebra crossings, trees along the route, front gardens, bus and tram stops, shops, business buildings, catering establishments, passing through parks or the city centre, and traffic volume. Litter on the street, high-rise buildings, and neighbourhood density of dwellings were negatively related to perceived link attractiveness. Overall, the results suggest that three main aspects affect perceived attractiveness of streets for walking, namely tidiness of the street, its scenic value and the presence of activity or other people along the street. The results are discussed within the context of these three aspects.     

Co-combustion of dried sewage sludge and coal in a pulverized coal boiler

More than 1.1 million tons of municipal and industrial sewage sludge is produced annually in Poland. Most of this sewage sludge is landfilled or used for recultivation and fertilization of soil. After accession of Poland to the EU, large investments are planned for wastewater treatment, so it is expected that the amount of sewage sludge produced in Poland will grow in the near future. It is well known that the combustion of sewage sludge is becoming a more and more popular utilization method of such waste. Unfortunately, the current situation in Poland makes it impossible to incinerate the sewage sludge because of a lack of incinerators. One possible solution for Poland is the co-firing of dried sewage sludge in existing coal-fired utility boilers. This article presents results of initial Polish industrial trials of dried municipal sewage sludge and hard coal co-combustion in an OP-230 pulverized coal boiler. Such a solution was shown to be technically viable and not to require changes to the existing technological system. Cocombustion of sewage sludge with coal in power plants seems to be the best solution for sludge utilization in the near future in Poland.     

Initial Changes in Refilled Lysimeters Built with Metal Polluted Topsoil and Acidic or Calcareous Subsoils as Indicated by Changes in Drainage Water Composition

Soil translocation for recultivation of soil removed from construction sites and for the preparation of refilled lysimeters inevitably involves disturbance of soil structure, and, if intermediate storage is included, also drying and rewetting of the soil. We report on an experiment with model forest ecosystems, where uncontaminated forest subsoils were covered with non-contaminated or freshly heavy metal (mainly Zn and Cu) contaminated topsoil in large lysimeters. Monitoring of the chemical composition of the drainage water revealed two distinct soil conditioning phases. During an initial phase of about a year strongly elevated nitrate and sulfate concentrations occurred that were attributed to a mineralisation flush caused by the increased accessability of mineralisable nitrogen and sulfur in destroyed aggregates. These effects were significantly larger in lysimeters with calcareous subsoil than in those with acidic subsoil. The second phase was characterised by a gradual decrease in dissolved organic carbon and sulfate concentrations, in particular in the acidic subsoil. This decrease may be attributed to the depletion of pools made accessible during aggregate destruction or the formation of new aggregates. These chemical changes had only little effects on the concentrations of copper and zinc in the drainage water. Based on our results, it can be concluded that large refilled lysimeters can be used for many purposes without risk of compromised results, if a conditioning phase of about 1 year with sufficiently moist soil conditions is respected. Nevertheless, gradual changes in soil chemical characteristics still occur after this initial phase. Implications for the recultivation of sites using relocated soils are discussed.     

Lysimeter Experiments to Investigate the Fate of Chemicals in Soils – Comparison of Five Different Lysimeter Systems

Several lysimeter scenarios and approaches exist to study the fate of agro-chemicals or contaminants from deposition in soil columns. In many systems just transport and leaching of the parent compound is followed, in some systems the leaching and transport of the metabolites is investigated as well. In more sophisticated lysimeter systems the volatilization and also the mineralization of the applied chemicals can be additionally monitored. Depending on the lysimeter system used and on the fact whether the applied chemicals are ¹⁴C-labeled or not, different results and various interpretations of the results might be achieved. Different lysimeter systems are described in this paper and a real dataset of a specific lysimeter experiment was transferred and evaluated in a virtual approach in the different lysimeter systems in order to show the advantages and disadvantages of the various systems.     

Enhancement of turbulent scalar mixing and its application by a multihole nozzle in selective catalytic reduction of NOx

The mixing characteristics of a passive scalar in the turbulent flow of a selective catalytic reduction process were numerically and experimentally investigated, focusing especially on an injection nozzle with multiple holes for the reducing agent. The multihole injection nozzle studied has six holes that are perpendicular to the ambient flue gas flow and are located near the tip of the nozzle. Large eddy simulation was applied to the turbulent flow and mixing fields to elucidate the mixing mechanism of the proposed nozzle compared with the single-hole nozzle that is commonly used in the conventional selective catalytic reduction process. From the results, there exist broader regions of higher turbulent intensities for the multihole nozzle than for the conventional single-hole nozzle. These regions are well matched with the positions of high vorticity in the near upstream region of the jet flow issuing from the multiple holes of the nozzle. Consequently, the high turbulent intensities and vorticity magnitudes lead to intensified mixing between the flue gas and the reducing agent. Hence, the most suitable molar ratio between NOx and the reducing agent for the catalytic reaction can be easily obtained within a shorter physical mixing length as a result of the enhanced scalar mixing. Finally, the numerical results were applied to a trial design version of a multihole nozzle, and this nozzle was experimentally tested to confirm its mixing performance.