New Approaches to the Design of Afterburners for Varnish Cookers

The best method of controlling varnish kettle emissions is by thermal incineration. Two new approaches have been developed; these utilize the integral-blower burner and the non-powered raw gas burner. Both of these new approaches offer significant advantages over conventional methods of incineration. Installation, operating, and maintenance costs are substantially reduced when either approach is utilized.

When compared to conventional methods, the new approaches achieve an increase of 100% in mixing velocity or turbulence. This results in a reduction of 20% in fuel consumption. Residence time is reduced by 29% via the non-powered raw gas burner approach. An average reduction of 65% is obtained in the length to diameter ratio. Choice of which approach depends upon several factors, primarily the type of fuel available and the minimum oxygen concentration in the fume stream.     

Modifications to an H2S Tape Sampler for Increasing Sensitivity and Accuracy in H2S Sampling

The tape samplers using lead acetate impregnated paper tapes for continuous hydrogen sulfide sampling are subject to a number of errors which can throw considerable doubt on the accuracy of H₂S concentrations being measured. Some of the errors have been minimized with a change in the humidification system and a reduction of the lamp intensity in the optical system.     

Emissions from Slash Burning and the Influence of Flame Retardant Chemicals

Pollutants sampled during the burning of 30 lb ponderosa pine fuel beds yielded emission factors for CO, hydrocarbon gases, and par-ticulate matter of 146, 8.4, and 9.1 lb/ton of fuel, respectively. When similar beds were treated with diammonium phosphate flame retardant, these factors increased to 166, 11.7, and 19.3 lb/ton of fuel, respectively.

Gas chromatographic analysis of hydrocarbon gases showed that 15-40% of this material was composed of methane and eth-ylene. Ethane and acetylene were the next most abundant materials, with photochemically important materials constituting minor portions of this gaseous component. Fuel beds treated with flame retardant produced more oiefins, and this production lasted throughout the smoldering phase of burning.

These tests showed that the smoldering phase of combustion is of major importance to air pollutant production during slash burning. The initial 80% of the fuel burned accounted for only 20-30% of HC and CO emissions. This suggests that a rapid mop-up of slash burns could substantially reduce air pollutant production.     

The Nationwide Program for Maintenance of Air Quality

The initial state implementation plans concentrated on attainment of the ambient air quality standards in the relatively polluted areas of the country. Many of these plans must now be modified to ensure that the ambient standards will be maintained for the foreseeable future, and to ensure that significant deterioration of air quality in clean areas of the country is prevented.

The existing implementation plans currently contain many measures which are applicable to the maintenance and deterioration efforts, but additional measures must also be developed. Many of these additional measures will involve future planning activities—most common of which will be land use planning activities.

The point is made that, after existing sources have reduced their emissions to the lowest practical level, further air pollution control can only be accomplished by implementing rational planning procedures for management of any new sources of air pollution. This will require extensive cooperation among the air pollution control community; regional, state, and local planning agencies; state and local governments; and the general public in order to ensure that future land use plans include appropriate air quality considerations.     

Stack Sampling of Hygroscopic Particulates In an Entrained Water Environment

Reference methods for the determination of mercury emissions from stationary sources typically include collection of mercury by solutions which are acidic and oxidizing. In the presence of high levels of SO₂ the oxidizing capacity of these absorbing solutions will be degraded and the collection efficiency for mercury compromised. This seriously limits the usefulness of the reference methods as they apply to the mining and smelting industries. In the present work peroxide is used to remove SO₂ and acidic permanganate is used to collect mercury. At a mean sampling rate of 10 L/min concentrations of at least 12 mg/m³ mercury can be satisfactorily collected in the presence of up to 20,000 ppm SO₂.     

Methylcyclopentadienyl Manganese Tricarbonyl as an Antiknock: Composition and Fate of Manganese Exhaust Products

Methylcyclopentadienyl manganese tricarbonyl (MMT) has been marketed as a combustion improver for fuel oil and turbine fuel. Use concentrations for this purpose are about 0.025 g manganese/gal in fuel oil and 0.08 to 0.5 g/gal in turbine fuels. In addition, it has been used to a small extent in gasoline.     

Author’s Reply

A technique is developed to compute precision requirements for component parts of an emissions inventory to ensure (at a given confidence level) an overall acceptable precision in the estimate of total emissions. Since the emissions inventory is a basic requirement of air quality control implementation plans and provides a valuable management tool for planning air pollution control activities, it isi appropriate to state in quantitative terms the confidence that can be associated with each inventory. The approach reported here uses weighted sensitivity analysis methods to distribute both percentage and physical errors in source class emissions according to their contribution to the total emissions, and utilizes Chebyshev’s inequality to establish confidence levels for total emissions. The analysis has been extended to cover the case where one or more of the error components in a given inventory source class can be fixed by the analyst. The utility of the technique is manifold and several practical applications are reported. In particular, it serves to establish percentage error requirements for source categories to satisfy given error bounds for the overall emissions inventory at a given level of statistical confidence. The weighted sensitivity analysis technique possesses a high degree of generality, being applicable to compute component error requirements for any kind of data inventory which exhibits a hierarchical (tree-like) structure, as exemplified by NEDS Emissions Summary Reports. This work should be of interest to air pollution control planners at all levels of government and to anyone responsible for the air pollution portion of environmental impact statements.     

Status and Problems of Regenerable Flue Gas Desulfurization Processes

Fourteen sulfur and/or sulfuric acid producing regenerate FGD processes were discussed at the 1974 FGD Symposium in Atlanta. During the period elapsed since then, considerable status change has occurred on many of these regenerable processes. Other regenerable processes which were not as well known during 1974 have surfaced in 1975. The problems of obtaining reducing gases (hydrogen sulfide, carbon monoxide, and hydrogen) for the reduction of sulfur dioxide product streams to elemental sulfur have become severe due to shortages of natural gas or other petroleum based feedstock. A new sulfur producing process which employs CO and H₂ directly (rather than the H₂S required for liquid and vapor base Claus reactions) is gaining attention. This paper discusses briefly: (1) the announced status of the many regenerable FGD processes, (2) the problem of reductant gas supply, and (3) the effect on FGD processes of using coal based reducing gas instead of reformed natural gas.     

Performance and Cost Comparisons between Fabric Filters and Alternate Participate Control Techniques

A study was conducted to evaluate performance and cost comparisons of fabric filters and alternate fine particulate control techniques. In relating the removal of fine particulate to costs, due to the lack of fractional efficiency data, it was found necessary to treat a specific application in order to make the study manageable. The case chosen is that of the coal fired industrial boiler since Enviro-Systems has a pilot program in this application area.     

Collection Efficiency as a Function of Particle Size,Shape and Density: Theory and Experience

The performance features of both industrial and experimental fabric filter systems with respect to the concentration and particle size properties of the collector effluents are examined. From a qualitative viewpoint the factors that should influence significantly the collection characteristics of a fabric filter are dust properties, fabric properties, operating parameters, filter cleaning method, and critical interdependencies. The quantitative prediction of performance and the establishment of design parameters are limited for a generalized approach but data have been reported that provide excellent support for limited applications.