Improvements to lawn and garden equipment emissions estimates for Baltimore, Maryland

Lawn and garden equipment are a significant source of emissions of volatile organic compounds (VOCs) and other pollutants in suburban and urban areas. Emission estimates for this source category are typically prepared using default equipment populations and activity data contained in emissions models such as the U.S. Environmental Protection Agency's (EPA) NONROAD model or the California Air Resources Board's (CARB) OFFROAD model. Although such default data may represent national or state averages, these data are unlikely to reflect regional or local differences in equipment usage patterns because of variations in climate, lot sizes, and other variables. To assess potential errors in lawn and garden equipment emission estimates produced by the NONROAD model and to demonstrate methods that can be used by local planning agencies to improve those emission estimates, this study used bottom-up data collection techniques in the Baltimore metropolitan area to develop local equipment population, activity, and temporal data for lawn and garden equipment in the area. Results of this study show that emission estimates of VOCs, particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO2), and nitrogen oxides (NO(x)) for the Baltimore area that are based on local data collected through surveys of residential and commercial lawn and garden equipment users are 24-56% lower than estimates produced using NONROAD default data, largely because of a difference in equipment populations for high-usage commercial applications. Survey-derived emission estimates of PM and VOCs are 24 and 26% lower than NONROAD default estimates, respectively, whereas survey-derived emission estimates for CO, CO2, and NO(x) are more than 40% lower than NONROAD default estimates. In addition, study results show that the temporal allocation factors applied to residential lawn and garden equipment in the NONROAD model underestimated weekend activity levels by 30% compared with survey-derived temporal profiles.     

Nocturnal boundary layer characteristics and land breeze development in Houston,Texas during TexAQS II

The nocturnal boundary layer in Houston, Texas was studied using a high temporal and vertical resolution tethersonde system on four nights during the Texas Air Quality Study II (TexAQS II) in August and September 2006. The launch site was on the University of Houston campus located approximately 4 km from downtown Houston. Of particular interest was the evolution of the nocturnal surface inversion and the wind flows within the boundary layer. The land–sea breeze oscillation in Houston has important implications for air quality as the cycle can impact ozone concentrations through pollutant advection and recirculation. The results showed that a weakly stable surface inversion averaging in depth between 145 and 200 m AGL formed on each of the experiment nights, typically within 2–3 h after sunset. Tethersonde vertical winds were compared with two other Houston data sets (High Resolution Doppler Lidar and radar wind profiler) from locations near the coastline and good agreement was found, albeit with a temporal lag at the tethersonde site. This comparison revealed development of a land breeze on three nights which began near the coastline and propagated inland both horizontally and vertically with time. The vertical temperature structure was significantly modified on one night at the tethersonde site after the land breeze wind shift, exhibiting near-adiabatic profiles below 100 m AGL.     

Why ozonolysis may not increase the hydrophilicity of particles

It is commonly assumed that atmospheric oxidation of hydrocarbon particles or hydrocarbon coatings on particles leads to polar products and increased water uptake, altering atmospheric visibility and increasing the likelihood they will act as cloud condensation nuclei (CCN). We show here through laboratory experiments that increased water uptake depends on the 3-dimensional structure of the particles. Laboratory studies of particles formed during ozonolysis of surface-bound alkenes, present as terminally unsaturated self-assembled monolayers (C8= SAM) on a silica substrate, were carried out at room temperature and 1 atm pressure. SAMs were exposed to ～10¹³ O₃ molecules cm^?3 for 40 min and resultant particles were analyzed using single particle Fourier transform infrared micro-spectroscopy (micro-FTIR) and secondary ion mass spectroscopy (SIMS). Spectroscopy results show that –COOH and other polar groups are formed but are buried inside a hydrophobic shell, consistent with earlier observations (McIntire et al., 2005, Moussa et al., 2009) that water uptake does not increase after reaction of the terminal alkene with O₃. These insights into the 3-D structure of particles formed on oxidation have important implications for the ability of secondary organic aerosols to act as CCN. In addition, the nature of the surface of the particles is expected to determine their uptake into biological systems such as the surface of the lungs.     

Improved land cover and emission factors for modeling biogenic volatile organic compounds emissions from Hong Kong

This paper describes a study of local biogenic volatile organic compounds (BVOC) emissions from the Hong Kong Special Administrative Region (HKSAR). An improved land cover and emission factor database was developed to estimate Hong Kong emissions using MEGAN, a BVOC emission model developed by Guenther et al. (2006). Field surveys of plant species composition and laboratory measurements of emission factors were combined with other data to improve existing land cover and emission factor data. The BVOC emissions from Hong Kong were calculated for 12 consecutive years from 1995 to 2006. For the year 2006, the total annual BVOC emissions were determined to be 12,400 metric tons or 9.82 × 10⁹ g C (BVOC carbon). Isoprene emission accounts for 72%, monoterpene emissions account for 8%, and other VOCs emissions account for the remaining 20%. As expected, seasonal variation results in a higher emission in the summer and a lower emission in the winter, with emission predominantly in day time. A high emission of isoprene occurs for regions, such as Lowest Forest-NT North, dominated by broadleaf trees. The spatial variation of total BVOC is similar to the isoprene spatial variation due to its high contribution. The year to year variability in emissions due to weather was small over the twelve-year period (?1.4%, 2006 to 1995 trendline), but an increasing trend in the annual variation due to an increase in forest land cover can be observed (+7%, 2006 to 1995 trendline). The results of this study demonstrate the importance of accurate land cover inputs for biogenic emission models and indicate that land cover change should be considered for these models.     

Analytical Solutions to the Linearized Boussinesq Equation for Assessing the Effects of Recharge on Aquifer Discharge1

Boggs, Kevin G., Robert W. Van Kirk, Gary S. Johnson, Jerry P. Fairley, and P. Steve Porter, 2010. Analytical Solutions to the Linearized Boussinesq Equation for Assessing the Effects of Recharge on Aquifer Discharge. Journal of the American Water Resources Association (JAWRA) 46(6):1116–1132. DOI: 10.1111/j.1752-1688.2010.00479.x Abstract: There is a need to develop a general understanding of how variations in aquifer recharge are reflected in discharge. Analytical solutions to the linearized Boussinesq equation governing flow in an unconfined aquifer provide a unified mathematical framework to quantify relationships among lag time, attenuation and distance between aquifer recharge and discharge and the effect of an up-gradient no-flow boundary. We applied this framework to three types of recharge: (1) instantaneous, (2) periodic, and (3) constant rate for a finite duration. When the temporal scale of recharge exceeds the diffusive aquifer time scale, recharge will be reflected in discharge quickly and with little attenuation. When aquifer time scale is large, most recharge events are shorter in scale than that of the aquifer, resulting in large attenuation. Attenuation is more sensitive to boundary effects than lag time, and boundary effects increase as recharge time scale increases. Boundary effects can often be ignored when the recharge source is farther than 1/3 of the domain length away from the no-flow boundary. We illustrate analytical results with application to the economically critical Eastern Snake River Plain Aquifer in Idaho. In this aquifer, detectable annual and decadal cycles in discharge can result from recharge no farther than 20 and 60 km away from the discharge point, respectively. The effects of more distant, long-term recharge can be detected only after a time lag of several decades.     

Dealing with disjunct concentration measurements in eddy covariance applications: A comparison of available approaches

Using proton transfer reaction mass spectrometry equipped with a quadrupol mass analyser to quantify the biosphere-atmosphere exchange of volatile organic compounds (VOC), concentrations of different VOC are measured sequentially. Depending on how many VOC species are targeted and their respective integration times, each VOC is measured at repeat rates on the order of a few seconds. This represents an order of magnitude longer sample interval compared to the standard eddy covariance (EC) method (5–20 Hz sampling rates). Here we simulate the effect of disjunct sampling on EC flux estimates by decreasing the time resolution of CO₂ and H₂O concentrations measured at 20 Hz above a temperate mountain grassland in the Austrian Alps. Fluxes for one month are calculated with the standard EC method and compared to fluxes calculated based on the disjunct data (1, 3 and 5 s sampling rates) using the following approaches: i) imputation of missing concentrations based on the nearest neighbouring samples (iDEC_nn), ii) imputation by linear interpolation (iDEC_li), and iii) virtual disjunct EC (vDEC), i.e. flux calculation based solely on the disjunct concentrations. It is shown that the two imputation methods result in additional low-pass filtering, longer lag times (as determined with the maximum cross-correlation method) and a flux loss of 3–30% as compared to the standard EC method. A novel procedure, based on a transfer function approach, which specifically corrects for the effect of data treatment, was developed, resulting in improved correspondence (to within 2%). The vDEC method yields fluxes which approximate the true (20 Hz) fluxes to within 3–7% and it is this approach we recommend because it involves no additional empirical corrections. The only drawback of the vDEC method is the noisy nature of the cross-correlations, which poses problems with lag determination – practical approaches to overcome this limitation are discussed.     

The application of profluorescent nitroxides to detect reactive oxygen species derived from combustion-generated particulate matter: Cigarette smoke – A case study

Reactive oxygen species (ROS) and related free radicals are considered to be key factors underpinning the various adverse health effects associated with exposure to ambient particulate matter. Therefore, measurement of ROS is a crucial factor for assessing the potential toxicity of particles. In this work, a novel profluorescent nitroxide, BPEAnit, was investigated as a probe for detecting particle-derived ROS. BPEAnit has a very low fluorescence emission due to inherent quenching by the nitroxide group, but upon radical trapping or redox activity, a strong fluorescence is observed. BPEAnit was tested for detection of ROS present in mainstream and sidestream cigarette smoke. In the case of mainstream cigarette smoke, there was a linear increase in fluorescence intensity with an increasing number of cigarette puffs, equivalent to an average of 101 nmol ROS per cigarette based on the number of moles of the probe reacted. Sidestream cigarette smoke sampled from an environmental chamber exposed BPEAnit to much lower concentrations of particles, but still resulted in a clearly detectible increase in fluorescence intensity with sampling time. It was calculated that the amount of ROS was equivalent to 50 ± 2 nmol per mg of particulate matter; however, this value decreased with ageing of the particles in the chamber. Overall, BPEAnit was shown to provide a sensitive response related to the oxidative capacity of the particulate matter. These findings present a good basis for employing the new BPEAnit probe for the investigation of particle-related ROS generated from cigarette smoke as well as from other combustion sources.     

Influence of roads and inhabited areas on metal concentrations in terrestrial mosses

The guidelines regarding sampling terrestrial mosses for biomonitoring the atmospheric contamination in a region specifically recommend that sampling close to focal points of contamination (i.e. roads, populated areas, etc.) should be avoided for satisfactory characterization of general patterns of contamination. However, these recommendations cannot always be followed in many parts of the world with dense, highly dispersed populations. The aim of the present study was to determine how the distances between sampling sites (SS) and contamination foci such as roads, isolated houses and urban nuclei affect regular, large-scale sampling networks. Metal concentrations obtained in biennial sampling surveys carried out between 2000 and 2006 in Galicia (NW Spain) were used, and the relative proportions of the concentrations corresponding to small-scale and large-scale processes were calculated. The possible relationship between the mean concentrations corresponding to small-scale processes in the different sampling surveys and the distances from SS to roads, buildings and urban nuclei was established by a GIS. Outliers in the data were identified at many of the SS and frequency statistics revealed the absence of any relationship between the distance to these foci and the concentrations of metals in the moss. The method also revealed many instances of the influence of one or more small-scale contamination foci such as airports and railways (often not considered in the sampling recommendations) on SS. Relocation of such SS would improve the representativeness of the sampling grid.     

Seasonal monoterpene and sesquiterpene emissions from Pinus taeda and Pinus virginiana

Seasonal volatile organic compound emission data from loblolly pine (Pinus taeda) and Virginia pine (Pinus virginiana) were collected using branch enclosure techniques in Central North Carolina, USA. P. taeda monoterpene emission rates were at least ten times higher than oxygenated monoterpene and sesquiterpene emissions in all seasons. α-pinene and β-pinene were the most abundant emissions, while β-caryophyllene had the highest sesquiterpene emission rate from this species. β-phellandrene was the dominant compound emitted from P. virginiana, followed by the sesquiterpene β-caryophyllene. Sesquiterpene emissions from P. virginiana have not been reported in the literature previously. Summer sesquiterpene emissions from P. virginiana were nearly as high as monoterpene emissions, but were 4–12 times lower than monoterpene emissions in the other seasons. Oxygenated monoterpenes and 2-methyl-3-buten-2-ol were emitted at higher rates from P. taeda than from P. virginiana. Temperature response of the pinenes from P. taeda is similar to previously reported values used in emission models, while that for other compounds falls at the lower end of the previously reported range. Temperature response of all compounds from P. virginiana is in reasonable agreement with previously reported values from other pine species. There is evidence of light dependence of sesquiterpene emission after accounting for temperature response from both species. This effect is somewhat stronger in P. taeda. Bud break, needle expansion, and needle fall (and therefore wind events) seemed to increase monoterpene emission during non-summer seasons. In some instances springtime monoterpene emissions were higher than summertime emissions despite cooler temperatures. Emissions of individual compounds within monoterpene, oxygenated monoterpene, and sesquiterpene classes were highly correlated with each other. Compounds from different classes were much less correlated within each species. This is due to a varying temporal emission patterns for each BVOC class and suggests different production, storage, and emission controls for each. Analysis of enclosure blanks and diurnal patterns indicates that, despite precautions, disturbance due to the enclosure technique may still impact monoterpene emission rate estimates. This did not appear to affect sesquiterpene emissions.     

Verification of diffusive and pumped samplers for volatile organic compounds using a controlled atmosphere test facility

There is a requirement to verify the performance of sorbent-based passive or active samplers and to extend their use, where possible, to monitor volatile organic compounds (VOCs) that are known to be photochemical ozone pre-cursors or are relevant to the activities of the petrochemical industry. We report measurements of the 14-day diffusive uptake rates for the VOCs: i-butane (2-methyl propane), n-butane, i-pentane (2-methyl butane), n-pentane, n-hexane, benzene, toluene, and m-xylene (at environmental level concentrations) for industry standard axial samplers (Perkin–Elmer-type samplers) containing the sorbents Carbopack-X, -Z, -B or Tenax-TA. We also present data on back-diffusion, blank levels, and storage for the above sorbents, and describe the simultaneous use of the sorbent Carbopack-X for pumped sampling of certain VOCs. The results were obtained by dosing samplers in a controlled atmosphere test facility (CATFAC) operating under well-defined conditions of concentration, nominal temperature of 20 °C, wind speed of 0.5 m s^?1, and relative humidities of 0% and 80%. Field measurements were also obtained to provide supplementary data to support the laboratory study. Results are compared to existing published data, where these are available.