水杨酸法检测水质氨氮的改进方法

该氨氮检测方法是对水杨酸分光光度法的改进,通过将50 g/L的水杨酸改为150 g/L的水杨酸钠,将有效氯为3. 5 g/L的次氯酸钠溶液改为5 g/L的二氯异氰尿酸钠溶液,增加了检测试剂的稳定性和贮存时间,同时将氨氮测定上限从1 mg/L提高至2. 5 mg/L,并将显色时间从60 min优化为30 min,使得此方法更为便捷。该方法的氨氮标准曲线线性关系良好,相关系数为0. 999 6,准确性和精密度高,加标回收率良好,适用于不同类型水质中氨氮的检测。     

道路交通的社会影响:当地居民的意见和优先考虑顺序

道路交通的社会影响评价经常基于客观指标或专家判断,没有征求被影响社区的意见。此文以一个拟建核电站对乡村地区的影响为例,探讨了当地居民对施工交通造成的影响和可能的减缓措施的意见和优先考虑。研究包括一个定性分析和一个优先考虑调查。使用了计量经济学模型来权衡不同影响和减缓措施的相对优先顺序。影响最大的因素是噪声、振动和增加的机动车交通频次。最受欢迎的减缓措施是夜间限制载重车辆、停车限制和对行人及骑自行车人员的安全保护。优先顺序受被调查人的居住地点、性别、就业状况和家庭组成影响,区别很大。研究指出,现有评价框架里有些信息是趋于合并的,应区分某些活动(如散步和开车)的主动减少和这些活动的被动停止。     

MoS_2/Bi_2S_3异质结光催化剂的制备及其光催化性能

以五水硝酸铋为铋源、钼酸钠为钼源、硫脲为硫源,采用简单的一步水热法合成了MoS_2/Bi_2S_3异质结光催化剂,采用XRD,SEM,TEM,BET,UV-Vis DRS技术对其进行了表征。表征结果显示,MoS_2纳米片在Bi_2S_3微棒表面生长,增加了比表面积和活性位点,并形成异质结构,促进了光生载流子的迁移,抑制了电子-空穴对的再复合。实验结果表明:钼酸钠与五水硝酸铋的质量比为1∶2时制备的复合光催化剂性能最好,反应180min时对亚甲基蓝的去除率可达96.4%,明显高于MoS_2和Bi_2S_3,且具有较高的稳定性;该催化剂对罗丹明B、甲基橙和4-硝基苯酚的去除率分别为97.1%、93.1%和90.5%,表明其对污染物具有普适性。     

Baked Foams Based on Cassava Starch Coated with Polyvinyl Alcohol with a Higher Degree of Hydrolysis

The aims of this work were to produce trays based on cassava starch, coated with polyvinyl alcohol (PVA) with a higher degree of hydrolysis (98%), and to study the effects of the coating on the mechanical and water sorption properties of the trays. Two types of PVA were tested: SELVOL? 325 (degree of polymerization?=?1000–1500) and SELVOL? 107 (degree of polymerization?=?350–650). A decrease in the water absorption capacity of 50% was observed when the coated samples were compared with the control sample after 30 min of immersion in water. It was observed in both coated samples a reduction of the initial rate of water adsorption sorption and a decrease in hydrophilicity compared with the control sample. Tensile strength and elongation were increased with application of the coatings. The use of the two types of PVA resulted in materials with similar mechanical and water sorption properties.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Preparation and Characterization of Collagens from the Skin of Northern Snakehead (<Emphasis Type="Italic">Channa argus)</Emphasis>

Channa argus, a type of snakehead fish native to China, is a popular food fish in certain Asian countries but is a known destructive invasive species in the US. In this study, the two collagens, i.e. acid-soluble collagen (ASC) and pepsin-solubilized collagen (PSC), were obtained from C. argus skin. The yield of ASC was 28.0% and that of PSC was 16.8% on the dry bases. The collagens were identified as the collagen of type I by SDS–PAGE patterns. The Tds were approximately 27.0?°C. Similar ultraviolet spectra of both collagens were observed. Fourier Transform infrared spectra indicated PSC structure had a little change due to the loss of terminal domains by pepsin digestion. The results of XRD proved that the two collagens retained their helical structures. The results suggest that the collagens isolated from C. argus can potentially be alternative sources of vertebrate collagens for use in the food and other industries.     

Optimal Reorganization of NASA Earth Science Data for Enhanced Accessibility and Usability for the Hydrology Community

A long‐standing “Digital Divide” in data representation exists between the preferred way of data access by the hydrology community and the common way of data archival by earth science data centers. Typically, in hydrology, earth surface features are expressed as discrete spatial objects (e.g., watersheds), and time‐varying data are contained in associated time series. Data in earth science archives, although stored as discrete values (of satellite swath pixels or geographical grids), represent continuous spatial fields, one file per time step. This Divide has been an obstacle, specifically, between the Consortium of Universities for the Advancement of Hydrologic Science, Inc. and NASA earth science data systems. In essence, the way data are archived is conceptually orthogonal to the desired method of access. Our recent work has shown an optimal method of bridging the Divide, by enabling operational access to long‐time series (e.g., 36 years of hourly data) of selected NASA datasets. These time series, which we have termed “data rods,” are pre‐generated or generated on‐the‐fly. This optimal solution was arrived at after extensive investigations of various approaches, including one based on “data curtains.” The on‐the‐fly generation of data rods uses “data cubes,” NASA Giovanni, and parallel processing. The optimal reorganization of NASA earth science data has significantly enhanced the access to and use of the data for the hydrology user community.     

Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

Energy efficiency and appliance’s characteristics considered prior to purchase: Differences and similarities between the United Kingdom,Germany, Portugal,Greece, Poland,Spain and Italy

This article reports country differences in the consumer’s most considered characteristics when choosing electrical appliances, including but not restricted to the energy efficiency aspect. A survey was performed to store customers from 7 countries: the United Kingdom; Germany; Portugal; Greece; Poland; Spain; Italy. Results showed consistency between countries in the top three characteristics considered: cost; quality; and a balance between price and quality. Differences were found for reported environmental attitudes and behaviours, purchase motives, and store employees evaluation. The results may support national policies and store level energy efficiency interventions. Specifically, they can provide input for store employee’s training, in persuading customers towards the purchase of energy efficient appliances.     

Increasing the recovery of heavy metal ions using two microbial fuel cells operating in parallel with no power output

The present study aimed to improve the performance of microbial fuel cells (MFCs) by using an intermittent connection period without power output. Connecting two MFCs in parallel improved the voltage output of both MFCs until the voltage stabilized. Electric energy was accumulated in two MFCs containing heavy metal ions copper, zinc, and cadmium as electron acceptors by connection in parallel for several hours. The system was then switched to discharge mode with single MFCs with a 1000-Ω resistor connected between anode and cathode. This method successfully achieved highly efficient removal of heavy metal ions. Even when the anolyte was run in sequencing batch mode, the insufficient voltage and power needed to recover heavy metals from the cathode of MFCs can be complemented by the developed method. The average removal ratio of heavy metal ions in sequencing batch mode was 67 % after 10 h. When the discharge time was 20 h, the removal ratios of zinc, copper, and cadmium were 91.5, 86.7, and 83.57 %, respectively; the average removal ratio of these ions after 20 h was only 52.1 % for the control group. Therefore, the average removal efficiency of heavy metal ions increased by 1.75 times using the electrons stored from the bacteria under the open-circuit conditions in parallel mode. Electrochemical impedance data showed that the anode had lower solution resistance and polarization resistance in the parallel stage than as a single MFC, and capacitance increased with the length of time in parallel.