Warm forming die design,part I: Experimental validation of a novel thermal finite element modeling code

Finite element analysis (FEA) has become an invaluable tool in the design of sheet metal stamping dies and processes. FEA has gained widespread acceptance as the best method of optimizing dies for conventional stamping processes. More recently, FEA has been shown to be an effective method of designing tooling for sheet forming processes. In this work, an FEA based approach is applied to the warm stamping (warm forming) process. This work introduces a new thermal finite element analysis software called PASSAGE®/Forming (PASSAGE) that enables the up-front design of the thermal management of warm forming dies. This thermal finite element analysis software is designed to specifically handle the forming and optimization scenarios related to the heating of a stamping die while minimizing user interface time. In this work, PASSAGE has been applied to a simple block of steel embedded with cartridge heaters to validate the prediction capability of this software under two different heating conditions. The results show that PASSAGE is capable of predicting the actual steady-state temperature distribution within the block with an acceptable level of accuracy while yielding notable information to the user with respect to specifying power requirements. A finite element software package like PASSAGE is a valuable tool that will aid greatly in the implementation of warm forming as a manufacturing process beyond the scope of the laboratory and into production.     

Meeting emission targets under uncertainty—the case of Finnish non-emission-trading sector

The European Union (EU) has set a target to reduce its greenhouse gas (GHG) emissions at least 10 % below the 2005 levels by 2020 in the non-Emission Trading Sector (non-ETS). As part of this, each Member State has a binding national emission limitation target for the non-ETS sector. Finland’s target, examined as a case study in this paper, is to reduce emissions at least 16 % below 2005 levels by 2020. The objective of this study is to find cost optimal mitigation portfolios that meet Finland’s reduction target and to analyze the risks of not attaining the emission target or exceeding the assumed costs. The question was addressed with a stochastic optimization model, Stochastic Optimization of non-ETS Emissions (SONETS) selecting separate mitigation measures that meet the target on expectation. The results show that optimal portfolios include relatively high uncertainty both in costs and achieved reductions. The prices of crude oil and diesel, and the abatement cost of reducing hydrofluorocarbon (HFC) emissions seem to account for the majority of uncertainty regarding total costs. The baseline predictions for various non-ETS subsectors (such as transport and agriculture) were found to have the greatest contribution to the uncertainty of attaining emission target. The results also show that some abatement actions are chosen in nearly all efficient portfolios, while other actions are seldom chosen. For example replacing oil burners in the end of technical life time or recovery of methane (CH₄) from waste are often chosen whereas ban of landfilling of organic waste is chosen extremely seldom. It also seems that the results are somewhat sensitive to the inclusion or exclusion of the interdependencies of mitigation measures.     

Resistance mash welding for joining of copper conductors for electric motors

The automotive industry is developing designs and manufacturing processes for a new generation of electric motors intended for use in hybrid and electric vehicles. This paper is focused on using solid-state welding to join rectangular wires in the fabrication of motor stators. Resistance welding has not typically been applied to copper due to its very high electrical conductivity; however through optimization of the current and pressure profiles, excellent quality copper-to-copper joints have been demonstrated with a technique known as resistance mash welding. A better understanding of resistance mash welding characteristics will help advancements in its application for stators. The limitations of this application will be discussed.     

Shellfish-Borne Viral Outbreaks: A Systematic Review

Investigations of disease outbreaks linked to shellfish consumption have been reported in the scientific literature; however, only few countries systematically collate and report such data through a disease surveillance system. We conducted a systematic review to investigate shellfish-borne viral outbreaks and to explore their distribution in different countries, and to determine if different types of shellfish and viruses are implicated. Six databases (Medline, Embase, Scopus, PubMed, Eurosurveillance Journal and Spingerlink electronic Journal) and a global electronic reporting system (ProMED) were searched from 1980 to July 2012. About 359 shellfish-borne viral outbreaks, alongside with nine ProMED reports, involving shellfish consumption, were identified. The majority of the reported outbreaks were located in East Asia, followed by Europe, America, Oceania, Australia and Africa. More than half of the outbreaks (63.6 %) were reported from Japan. The most common viral pathogens involved were norovirus (83.7 %) and hepatitis A virus (12.8 %). The most frequent type of consumed shellfish which was involved in outbreaks was oysters (58.4 %). Outbreaks following shellfish consumption were often attributed to water contamination by sewage and/or undercooking. Differences in reporting of outbreaks were seen between the scientific literature and ProMED. Consumption of contaminated shellfish represents a risk to public health in both developed and developing countries, but impact will be disproportionate and likely to compound existing health disparities.     

Detection of Viruses in Coastal Seawater Using <Emphasis Type="Italic">Mytilus Galloprovincialis</Emphasis> as an Accumulation Matrix

The purpose of this study was to demonstrate that shellfish can be used to detect enteric viruses in marine waters where they are present at very low concentrations. Aqua-cultured mussels were placed in the sea just off the mouth of a drainage channel affected by human and animal faecal contamination. Samples were taken from the channel, the sea and the mussels at intervals over two 4-week periods. The samples were tested to verify the presence of both rotaviruses and E. coli. Rotaviruses were detected by Real Time-PCR, typed by multiplex PCR and subsequently sequenced. E. coli was enumerated in water matrices by a filtering method and in mussels by the MPN method. The presence of E. coli in the examined matrices demonstrates contamination of faecal origin throughout the studied environments. Rotaviruses were recorded in channel waters, but not in sea water. In both experiments, rotaviruses were detected in mussels 21 and 28 days after being placed in the sea water off the channel mouth. The use of mussels thus enabled the detection of rotaviruses in waters where the high dilution rendered direct investigation impossible. This study indicates that mussels can be used in marine virological surveillance programs.     

Management strategies to mitigate the impacts of climate change on sea turtle’s terrestrial reproductive phase

Climate change poses a serious threat to sea turtles (Cheloniidae) as their terrestrial reproductive phase is only successful within a limited range of environmental and physical conditions. These conditions are likely to become less optimal as climate change progresses. To date, management and conservation of sea turtles has focused almost entirely on non-climatic stressors, due at least in part to practitioners not knowing what strategies to take and the feasibility and risks of potential strategies. To aid the management of sea turtles in a changing environment, we identified management strategies via a focus workshop and surveys to mitigate the impacts of climate change to the terrestrial reproductive phase of sea turtles. The effectiveness, ecological risks and potential social and logistical constraints associated with implementing each of the identified management strategies is discussed. Twenty management strategies were identified; strategies varied from habitat protection to more active and direct manipulation of nests and the nesting environment. Based on our results, we suggest a three-pronged approach to sea turtle conservation in light of climate change, where managers and researchers should: 1) enhance sea turtle resilience to climate change by mitigating other threats; 2) prioritise implementing the ‘no regret’ and ‘reversible’ management strategies identified here; and 3) fill the knowledge gaps identified to aid the trial and implementation of the potential strategies identified here. By combining these three approaches our collective toolkit of sea turtle management strategies will expand, giving us an array of viable approaches to implement as climate change impacts become more extreme.     

Dimensional analysis and scaling in mechanical mixing for fabrication of metal matrix nanocomposites

For a successful enhancement of mechanical properties of metal matrix nanocomposites, a homogeneous nanoparticle dispersion and distribution in the solidified metal is required. Mechanical mixing can be used for initial break-up of agglomerates, and its study can be simplified with dimensional analysis. Using this technique, mixing time and vortex height were assessed while varying fluid properties, impeller angle, and angular speed. Three relevant dimensionless numbers were recognized: the Reynolds (Re), Froude and Galilei (Ga) numbers. Based on blade and impeller shaft angles, a modified Froude number (Fr*) was defined. These parameters were calculated experimentally, varying angular speed from 200 to 1000 rpm for three different impeller angles: 0°, 15° and 30°. This procedure was performed with three fluids: water, and two aqueous glycerin solutions (25% and 50% by volume). Digital images were taken and processed to measure vortex height. Mixing time was measured for water at 0° impeller angle, angular speed ranging from 200 to 1200 rpm. Results showed an optimal dimensionless mixing time with respect to Re. A linear relationship was found between dimensionless vortex height and Fr*. The first had a second order polynomial relationship with the product ReFr*, regardless of impeller angle. This relationship, together with the Ga, specific for each fluid, allows scaling the results to other fluids such as molten pure aluminum. This study allows experimenting in simpler systems that involve transparent fluids, room temperature and low cost, to then elaborate a prediction of vortex height in fluids where measurements are difficult and costly, such as molten metals.     

Greenhouse gas mitigation and offset options for suckler cow farms: an economic comparison for the Swiss case

We assessed the economic suitability of 4 greenhouse gas (GHG) mitigation options and one GHG offset option for an improvement of the GHG balance of a representative Swiss suckler cow farm housing 35 Livestock units and cultivating 25 ha grassland. GHG emissions per kilogram meat in the economic optimum differ between the production systems and range from 18 to 21.9 kg CO₂-eq./kg meat. Only GHG offset by agroforestry systems showed the potential to significantly reduce these emissions. Depending on the production system agroforestry systems could reduce net GHG emissions by 66% to 7.3 kg CO₂-eq./kg meat in the most intensive system and by 100% in the most extensive system. In this calculation a carbon sequestration rate of 8 t CO₂/ha/year was assumed. The potential of a combination of the addition of lipids to the diet, a cover of the slurry tank and the application of nitrification inhibitors only had the potential to reduce GHG emissions by 12% thereby marginal abatement costs are increasing much faster than for agroforestry systems. A reduction of the GHG emissions to 7.5 kg CO₂-eq./kg meat—possible with agroforestry only—raised costs between 0.03 CHF/kg meat and 0.38 CHF/kg meat depending on the production system and the state of the system before the reduction. If GHG emissions were reduced maximally average costs ranged between 0.37 CHF/kg meat, if agroforestry had the potential to reduce net GHG emissions to 0 kg CO₂-eq., to 1.17 CHF/kg meat if also other options had to be applied.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Modeling and interpretation of fiber orientation-based failure mechanisms in machining of carbon fiber-reinforced polymer composites

The development and implementation of a microstructure-based finite element model for the machining of carbon fiber-reinforced polymer composites is presented. A new approach to interfacial modeling is introduced where the material interface is modeled using continuum elements, allowing failure to take place in either tension or compression. The model is capable of describing the fiber failure mode occurring throughout the chip formation process. Characteristic fiber length in the chips, and machining forces for microstructures with fibers orientated at 0°, 45°, 90°, and 135° are examined. For model validation purposes, the model-based machining performance predictions are compared to the machining responses from a set of orthogonal machining experiments. A parametric study is presented that identifies a robust tool geometry, which minimizes the effects of fiber orientation and size on the machining forces.