Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.     

Follow-up to environmental impact assessment: Learning from the Canadian Government experience

The environmental impact assessment procedure for Canadian federal government projects is briefly described. In the non-legislated Canadian system, follow-up to assessments is one of the major means of encouraging and improving the implementation of environmental impact assessment and the quality of environmental work done around development projects. The results of a study on the status of follow-up in the Canadian Government are presented. Factors that limit and that are conducive to follow-up are discussed. The effectiveness of follow-up depends as much on the circumstances surrounding a project and the concerned parties as on the follow-up techniques used; both of these aspects can be addressed in the planning and management of follow-up and of environmental impact assessment overall. Areas for improving the management of follow-up are identified and discussed: planning of follow-up activities, coordination of concerned parties, generation of clear understandings, information management, resource allocation, and maintenance of credibility. A method for planning follow-up activities for specific projects is presented.     

Soil sampling and analysis for volatile organic compounds

Concerns over data quality have raised many questions related to sampling soils for volatile organic compounds (VOCs). This paper was prepared in response to some of these questions and concerns expressed by Remedial Project Managers (RPMs) and On-Scene Coordinators (OSCs). The following questions are frequently asked:

1. Is there a specific device suggested for sampling soils for VOCs?
2. Are there significant losses of VOCs when transferring a soil sample from a sampling device (e.g., split spoon) into the sample container?
3. What is the best method for getting the sample from the split spoon (or other device) into the sample container?
4. Are there smaller devices such as subcore samplers available for collecting aliquots from the larger core and efficiently transferring the sample into the sample container?
5. Are certain containers better than others for shipping and storing soil samples for VOC analysis?
6. Are there any reliable preservation procedures for reducing VOC losses from soil samples and for extending holding times?

Guidance is provided for selecting the most effective sampling device for collecting samples from soil matrices. The techniques for sample collection, sample handling, containerizing, shipment, and storage described in this paper reduce VOC losses and generally provide more representative samples for volatile organic analyses (VOA) than techniques in current use. For a discussion on the proper use of sampling equipment the reader should refer to other sources (Acker, 1974; U.S. EPA, 1983; U.S. EPA, 1986a). Soil, as referred to in this report, encompasses the mass (surface and subsurface) of unconsolidated mantle of weathered rock and loose material lying above solid rock. Further, a distinction must be made as to what fraction of the unconsolidated material is soil and what fraction is not. The soil component here is defined as all mineral and naturally occurring organic material that is 2 mm or less in size. This is the size normally used to differentiate between soils (consisting of sands, silts, and clays) and gravels. Although numerous sampling situations may be encountered, this paper focuses on three broad categories of sites that might be sampled for VOCs:

1. Open test pit or trench.
2. Surface soils (<5 ft in depth).
3. Subsurface soils (>5 ft in depth).

     

Woodstove emission measurement methods: Comparison and emission factors update

On February 26, 1988, the U.S. Environmental Protection Agency promulgated Standards of Performance for residential wood heaters, or woodstoves. Over the past several years, a number of field studies have been undertaken to determine the actual level of emission reduction achieved by new technology woodstoves in everyday use. These studies have required the development and use of particulate and gaseous emission sampling equipment compatible with operation in private houses. Since woodstoves are tested for certification in the laboratory using EPA Methods 5G and 5H, it is of substantial interest to determine the correlation between these regulatory methods and the in-house equipment. Two in-house sampling systems have been used most widely. One is an intermittent, pump-driven particulate sampler which collects particulate and condensable organics on a filter and organic adsorbent resin. Oxygen concentration is measured by a sensor in the sample line. The sampler is controlled by a data logger which also records other parameters of interest. The second system uses an evacuated cylinder as the motive force. Particulate and condensable organics are collected in a condenser and dual filter. The sampler operates continuously whenever the stack temperature is above the set point. Average stack gas concentrations are measured from the evacuated cylinder at the conclusion of the sampling period. Both samplers were designed to operate unattended for 1-week periods. A large number of tests have been run comparing Methods 5G and 5H to both of the field samplers. This paper presents these comparison data and determines the relationships between laboratory certification sampling methods and field samplers.     

Cumulative impact assessment in environmental planning: A coastal wetland watershed example

Several theoretical, analytical, and institutional difficulties have impeded the development and application of the assessment of cumulative environmental impacts. Watershed development on coastal wetlands offers an ideal context for evaluating the land disturbance target approach to cumulative impact assessment. A model land use planning system involving a time series approach was developed for Elkhorn Slough in California. The approach included four major components: evaluation of erosion susceptibility, measurement of land disturbance, establishment of a land disturbance target, and a comparison of existing and target land disturbance values. Further research is needed to test the transferability of the approach in a wide range of coastal watersheds and to verify the applicability of the methods to other cumulative impact problems.     

Analysis of pollutant levels in central Hong Kong applying neural network method with particle swarm optimization

Air pollution has emerged as an imminent issue in modernsociety. Prediction of pollutant levels is an importantresearch topic in atmospheric environment today. For fulfillingsuch prediction, the use of neural network (NN), and inparticular the multi-layer perceptrons, has presented to be acost-effective technique superior to traditional statisticalmethods. But their training, usually with back-propagation (BP)algorithm or other gradient algorithms, is often with certaindrawbacks, such as: 1) very slow convergence, and 2) easilygetting stuck in a local minimum. In this paper, a newlydeveloped method, particle swarm optimization (PSO) model, isadopted to train perceptrons, to predict pollutant levels, andas a result, a PSO-based neural network approach is presented. The approach is demonstrated to be feasible and effective bypredicting some real air-quality problems.     

Design of National Groundwater Quality Monitoring Network in Egypt

In the Nile Valley and Delta the protection of groundwater resources is high priority environmental concern. Many groundwater quality problems are already dispersed and may be widespread and frequent in occurrence. Examples include problems associated with the extensive application of chemical fertilizers in agricultural specially in the new reclaimed areas, leaks in sewers, septic tanks, the aggregate effects of many different points source pollution in urban areas and natural, geologically related water quality problems. A national groundwater quality monitoring has been designed and implemented based on the stepwise procedure. The national groundwater quality monitoring network is used to quantify the quality changes in long run, either caused by pollution activities or by salt water intrusion and to describe the overall current groundwater quality status on a national scale of the main aquifers. The monitoring tools and methodologies developed in this research can be used to assure protection of public health and determine the sustainability of groundwater in various purposes. This national monitoring network plays important roles for decision makers in developing the groundwater resources management plans in different aquifers systems in Egypt.     

超临界二氧化碳萃取－GC／MS测定土壤中的多环芳烃

本文开发了一种采用超临界二氧化碳萃取土壤中多环芳烃、不须经过纯化步骤，直接可用于ＧＣ／ＭＳ分析的简便、高效的方法。本实验中超临界革取的流体是二氧化碳，改善剂是５％的二氯甲烷／甲醇，萃取温度为１２０℃、压力为３４ＭＰａ。ＧＣ／ＭＳ分析时除了采用外标外，还加入了６种同位素ＰＡＨｓ内标以校正各段ＰＡＨｓ的响应因子。采用本方法成功地测定了我国未开垦森林土壤中的ＰＡＨｓ。