The world is experiencing an energy crisis and environmental issues due to the depletion of fossil fuels and the continuous increase in carbon dioxide concentrations. Microalgal biofuels are produced using sunlight, water, and simple salt minerals. Their high growth rate, photosynthesis, and carbon dioxide sequestration capacity make them one of the most important biorefinery platforms. Furthermore, microalgae's ability to alter their metabolism in response to environmental stresses to produce relatively high levels of high-value compounds makes them a promising alternative to fossil fuels. As a result, microalgae can significantly contribute to long-term solutions to critical global issues such as the energy crisis and climate change. The environmental benefits of algal biofuel have been demonstrated by significant reductions in carbon dioxide, nitrogen oxide, and sulfur oxide emissions. Microalgae-derived biomass has the potential to generate a wide range of commercially important high-value compounds, novel materials, and feedstock for a variety of industries, including cosmetics, food, and feed. This review evaluates the potential of using microalgal biomass to produce a variety of bioenergy carriers, including biodiesel from stored lipids, alcohols from reserved carbohydrate fermentation, and hydrogen, syngas, methane, biochar and bio-oils via anaerobic digestion, pyrolysis, and gasification. Furthermore, the potential use of microalgal biomass in carbon sequestration routes as an atmospheric carbon removal approach is being evaluated. The cost of algal biofuel production is primarily determined by culturing (77%), harvesting (12%), and lipid extraction (7.9%). As a result, the choice of microalgal species and cultivation mode (autotrophic, heterotrophic, and mixotrophic) are important factors in controlling biomass and bioenergy production, as well as fuel properties. The simultaneous production of microalgal biomass in agricultural, municipal, or industrial wastewater is a low-cost option that could significantly reduce economic and environmental costs while also providing a valuable remediation service. Microalgae have also been proposed as a viable candidate for carbon dioxide capture from the atmosphere or an industrial point source. Microalgae can sequester 1.3 kg of carbon dioxide to produce 1 kg of biomass. Using potent microalgal strains in efficient design bioreactors for carbon dioxide sequestration is thus a challenge. Microalgae can theoretically use up to 9% of light energy to capture and convert 513 tons of carbon dioxide into 280 tons of dry biomass per hectare per year in open and closed cultures. Using an integrated microalgal bio-refinery to recover high-value-added products could reduce waste and create efficient biomass processing into bioenergy. To design an efficient atmospheric carbon removal system, algal biomass cultivation should be coupled with thermochemical technologies, such as pyrolysis.
This paper demonstrates the use of a flexible instrumented stamp to enable automated micro transfer printing as a route to large-area, deterministic assembly of microstructured device components or ‘inks’. The ability to instrument the stamp, a critical component for retrieval and placement of a micro device, to detect contact and monitor localized forces during critical events in the printing process not only allows for the development of a robust manufacturing process, but also for a unique vantage point from which to study fundamental issues and phenomena associated with adhesion and delamination of thin films from a variety of substrate materials. This paper presents basic design analysis on the requirements of the cantilevers for compatibility with a typical transfer printing environment. Off-the-shelf thin film strain gages are integrated with a thin elastomeric post as a preliminary prototype and the feasibility of transfer printing with it is demonstrated. Further, the set-up is calibrated to produce force signals for event detection and in situ diagnosis of the process. 相似文献
In an effort to assess the occurrence and sources of polycyclic aromatic hydrocarbons (PAHs) in the ambient air of Riyadh, Saudi Arabia, PM10 samples were collected during December 2010. Diagnostic PAH concentration ratios were used as a tool to identify and characterize the PAH sources. The results reflect high PM10 and PAH concentrations (particulate matter (PM)?=?270–1,270 μg/m3). The corresponding average PAH concentrations were in the range of 18?±?8 to 1,003?±?597 ng/m3 and the total concentrations (total PAHs (TPAHs) of 17 compounds) varied from 1,383 to 13,470 ng/m3 with an average of 5,871?±?2,830 ng/m3. The detection and quantification limits were 1–3 and 1–10 ng/ml, respectively, with a recovery range of 42–80 %. The ratio of the sum of the concentrations of the nine major non-alkylated compounds to the total (CPAHs/TPAHs) was 0.87?±?0.10, and other ratios were determined to apportion the PM sources. The PAHs found are characteristic for emissions from traffic with diesel being a predominant source. 相似文献
The widespread contamination of surface and ground water quality from the heavy use of fertilizer in modern agriculture is
the current concern. Therefore, this study was carried out to develop a slow-release fertilizer using charcoal. The morphology
of the charcoal impregnated fertilizer was investigated by scanning electron microscopy (SEM). This study also evaluated the
release patterns of N, P, and K from impregnated charcoal using a simulated soil solution and distilled water as leaching
solutions. The patterns of N, P, and K releases were examined in both static and continuous-flow conditions for 360 h. Releases
of N, P, and K from impregnated charcoal were found to be slow and steady. However, the release trends of N, P, and K were
higher in soil solution than distilled water under both the above conditions. Dissolution occurred when N, P, and K were released
in the above leached solutions. As a result, the fertilizer impregnated charcoal could be developed as slow-release type fertilizer
to minimize the contamination. 相似文献
Environmental Science and Pollution Research - The objective of this study is to contribute to the existing debate of green economic growth by empirically investigating the role of cleaner energy... 相似文献
Environmental Science and Pollution Research - Natural hazards and severe weather events are a matter of serious threat to humans, economic activities, and the environment. Flash floods are one of... 相似文献
Environmental Chemistry Letters - Globally, 150–170 billion cubic metres of gas are being flared annually from petroleum refineries, petrochemical industries and from landfills. In this... 相似文献
One of the major disadvantages of micropiles is their low lateral stiffness and flexural rigidity due to the small diameter. This limitation can be handled in current practice, by installing the micropile with inclined condition or providing a steel casing. Additional steel casings will increase the lateral load capacity of micropiles but increase the project cost as well. Thus, inclination of micropile which is relatively simple and cheap is recommended. In this paper, a comprehensive numerical analysis is conducted on the behavior of micropiled rafts installed with inclined condition under combined vertical and lateral loading. A FEM calibrated against full-scale axial and lateral field tests is used to conduct the analysis. The soil profile is soft clay soil underlain by a layer of dense sand. The study investigates the impact of several parameters which are as follows: magnitude of vertical loading, reinforcement type, inclination angle of micropiles, and number of inclined micropiles. The study reveals that increasing vertical loads causes continuous decrease in the lateral load capacity of micropiled rafts. When all micropiles installed are inclined, the positively inclined micropiles carry 79–86% of the total lateral load carried by micropiles, whereas the negatively inclined ones carry 14–21%. Inclined micropiles offer greater lateral load sharing ratio (αh) than that of vertical ones, largest at θ = 45°. The effect of micropile reinforcement on improving the lateral performance is low compared to the effect of micropile inclination angle.