Decomposition of NO in automobile exhaust by plasma–photocatalysis synergy

The combination of plasma discharge and TiO₂ photocatalysis exhibits high performances in the removal of nitrogen monoxide (NO). This article is aimed at elucidating the relationships between NO decomposition efficiency and various experimental parameters, including voltages, humidity and temperature. The experimental results indicate that the efficiency of NO removal by synergic plasma-catalyst coupling is significantly higher than plasma only or photocatalyst only systems. Moreover, the NO removal efficiency improves with the increase of applied voltage. Meanwhile, a higher humidity results in a reduced number of electron–hole pairs at the surface of TiO₂ photocatalyst, leading to lower synergic purification efficiencies. Finally, the efficiency of NO removal is raised with the increase of temperature due to the fact that the adsorption of NO and water by nano-TiO₂ is affected by environmental temperature.     

Source attribution for mercury deposition in the contiguous United States: regional difference and seasonal variation

Quantifying the contribution of emission sources responsible for mercury deposition in specific receptor regions helps develop emission control strategies that alleviate the impact on ecosystem and human health. In light of the maximum available control technology (MACT) rules proposed by U.S. Environmental Protection Agency (EPA) and the ongoing intergovernmental negotiation coordinated by United Nations Environmental Programme (UNEP) for mercury, the Community Multiscale Air Quality Modeling System (CMAQ-Hg) was applied to estimate the source contribution in six subregions of the contiguous United States (CONUS). The considered source categories include electric generating units (EGU), iron and steel industry (IRST), other industrial point sources excluding EGU and IRST (OIPM), the remaining anthropogenic sources (RA), natural processes (NAT), and out-of-boundary transport (BC). It is found that, on an annual basis, dry deposition accounts for two-thirds of total annual deposition in CONUS (474 Mg yr(-1)), mainly contributed by reactive gaseous mercury (about 60% of total deposition). The contribution from large point sources can be as high as 75% near the emission sources (< 100 km), indicating that emission reduction may result in direct deposition decrease near the source locations. Out-of-boundary transport contributes from 68% (Northeast) to 91% (West Central) of total deposition. Excluding the contribution from out-of boundary transport, EGU contributes to about 50% of deposition in the Northeast, Southeast, and East Central regions, whereas emissions from natural processes are more important in the Pacific and West Central regions (contributing up to 40% of deposition). This suggests that the implementation of the new EPA MACT standards will significantly benefit only these three regions. Emission speciation is a key factor for local deposition. The source contribution exhibits strong seasonal variation. Deposition is greater in warm seasons due to stronger Hg0 oxidation. However, the contribution from anthropogenic sources is smaller in warm seasons because of larger emissions from natural processes and stronger vertical mixing that facilitates transport.     

Effects of dissolved inorganic carbon and nutrient levels on carbon fixation and properties of Thermosynechococcus sp. in a continuous system

The concept of CO₂ chemo-absorption by sodium hydroxide in a wet scrubber followed by microalgae cultivation was used as a means to reduce the major greenhouse gas. A thermophilic and alkaline tolerable cyanobacterium named Thermosynechococcus CL-1 (TCL-1) was cultivated in continuous system, with a carbonate-bicarbonate buffer as carbon source. The effects of dissolved inorganic carbon (DIC_in) and nutrient levels in influent on cell mass productivity, DIC removal efficiency, and alkaline solution regeneration by TCL-1 were investigated. The results show the highest cell mass productivity reaches 1.7 g L⁻¹ d⁻¹ under the highest DIC and nutrients level. Conversely, the best regeneration of alkaline solution proceeds from pH 9.5 to 11.3 under the lowest level. In addition, the highest ΔDIC (DIC consumption) and DIC removal efficiency are 42 mM and 43% at 113.2 and 57 mM DIC_in, respectively.     

窑头篦冷机除尘系统改造技术探讨

分析了广州市珠江水泥有限公司的窑头电除尘改造为袋式除尘的成功案例。指出在设计和使用上,要控制好过滤风速、气流上升速度、净气室的风速、喷吹压力、脉冲时间和周期,以及气流分布等主要技术指标,袋式除尘器阻力可大幅度下降,除尘效率可大幅度提高。     

Impact of water quality parameters on the sorption of U(VI) onto hematite

In this study, the sorption of U(VI) from aqueous solution on hematite was studied as a function of various water quality parameters such as contact time, pH, ionic strength, soil humic acid (HA) or fulvic acid (FA), solid content and temperature by using a batch technique. The results demonstrated that the sorption of U(VI) was strongly dependent on ionic strength at pH < 6.0, and outer-sphere surface complexation may be the main sorption mechanism. The sorption was independent of ionic strength at pH > 6.0 and the sorption was mainly dominated by inner-sphere surface complexation. The presence of HA/FA increases U(VI) sorption at low pH, whereas decreases U(VI) sorption at high pH. The thermodynamic parameters (ΔH⁰, ΔS⁰, and ΔG⁰) were calculated from the temperature dependent sorption isotherms, and the results suggested that U(VI) sorption was a spontaneous and endothermic process. The results might be important for the application of hematite in U(VI) pollution management.     

耐盐石油降解菌性能及降解条件优化

从冀东油田钻井废液中筛选分离出耐盐石油降解菌Virgibacillus sp.(简称SJ菌),其在高含盐条件下对石油具有较好的降解效果,高达56.12%左右。考察了pH值、盐度、不同N和P形态等因素对SJ菌降解石油效果的影响。结果表明:SJ菌有较宽的pH值适应范围(pH值为6～10)和较好的耐盐能力(0.5%～20%),在pH值为9及NaCl质量浓度为5%时对石油类降解效果最好,其最佳利用N源和P源分别为(NH2)2CO和KH2PO4,该研究为油田高含盐含油废液处理提供了一条新途径。     

Comparison of the complex terrain algorithms incorporated into two commonly used local-scale air pollution dispersion models (ADMS and AERMOD) using a hybrid model

ADMS and AERMOD are the two most widely used dispersion models for regulatory purposes. It is, therefore, important to understand the differences in the predictions of the models and the causes of these differences. The treatment by the models of flat terrain has been discussed previously; in this paper the focus is on their treatment of complex terrain. The paper includes a discussion of the impacts of complex terrain on airflow and dispersion and how these are treated in ADMS and AERMOD, followed by calculations for two distinct cases: (i) sources above a deep valley within a relatively flat plateau area (Clifty Creek power station, USA); (ii) sources in a valley in hilly terrain where the terrain rises well above the stack tops (Ribblesdale cement works, England). In both cases the model predictions are markedly different. At Clifty Creek, ADMS suggests that the terrain markedly increases maximum surface concentrations, whereas the AERMOD complex terrain module has little impact. At Ribblesdale, AERMOD predicts very large increases (a factor of 18) in the maximum hourly average surface concentrations due to plume impaction onto the neighboring hill; although plume impaction is predicted by ADMS, the increases in concentration are much less marked as the airflow model in ADMS predicts some lateral deviation of the streamlines around the hill.     

乌梁素海表层沉积物重金属与营养元素含量的统计分析

对乌梁素海表层沉积物营养盐与重金属的分布情况进行研究,应用SPSS统计分析软件对乌梁素海表层沉积物重金属与营养元素进行相关分析和因子分析,并对重金属元素进行聚类分析。营养元素与重金属间的相关分析表明：重金属元素Cu、Cr、Pb和Cd相互间具有极显著的正相关性;有机质与As和Hg呈极显著的正相关;总氮与Hg呈极显著相关,与As呈显著相关,而与Pb呈极显著负相关,与Cd呈显著负相关;总磷与As呈显著负相关。重金属元素间的R-型聚类分析结果将本论文研究的9种金属元素分为3类。采用主成分分析法对乌梁素海表层沉积物重金属与营养元素进行因子分析,得到4个因子,并进一步分析讨论了各主成分的科学内涵。     

新型环保型自来水絮凝剂的研制及应用

根据“有机-无机”絮凝剂相复合协同增效的原则,研制出一种高效的复合环保型自来水絮凝剂,使其处理效果与传统絮凝剂比较,浊度下降0．65％,药剂成本下降9．29％,出水铝离子浓度比传统下降77．3％,无论从产品的性价比还是从环境友好等方面均明显优于传统的自来水絮凝剂,具有明显的经济与环境效益。     

Persistent organic pollutant emissions from medical waste incinerators in China

The huge amount of medical waste (MW) has caused a tough challenge to environmental protection in China because of its serious infectious potential. At present, incineration is the most common technology for MW disposal. Unfortunately, the medical waste incinerator (MWI) is considered one of the major sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). This study was conducted to investigate the generation and the components of MW; the fingerprint of PCDD/Fs in MWI; and PCDD/F, polychlorinated biphenyl (PCB) and hexachlorobenzene concentrations in residue ash. The estimated annual production of MW was estimated to be 0.97 million tons in China in 2008; in addition, plastic and rubber accounted for 24.5% of MW contents. PCDD/F emissions from MWI could be divided into two main groups according their fingerprints, and the ratio of PCDFs/PCDDs was mostly over 1.5, with a mean value of 3.43. The toxic equivalent of PCDD/Fs was over 30 times that of the value of PCBs in the residue ash, and PCDD/F contents in fly ash accounted for approximately 67% of the total output of PCDD/Fs, which was in line with the UNEP default emission factors for MWI (class 3, 63.7%).