Influence of environmental parameters on the accuracy of nitrogen dioxide passive diffusion tubes for ambient measurement

Two studies at three sites in the UK provided confirmation that systematic positive bias in NO2 diffusion tube measurement occurred because of changes to "within-tube" chemistry, rather than eddy diffusion at the mouth of the tube. In the first study in Cambridge, UK, sampler overestimation for 1 and 2 week exposures was compared to corresponding time-averaged monitor measurements (NO-NO2-NOx, O3) and weather variables. Noninearity between sampler and monitor NO2 measurements was interpreted in terms of spatial and temporal variations in relative and absolute availability of NO, NO2 and O3 at the site. A maximum overestimation occurred for an exposure mean NO2/NOx approximately 0.5. The separate contributions of reduced NO2 photolysis and eddy diffusion were compared in Study II using samplers of two materials, acrylic and quartz, and of different lengths (40, 55, 71 and 120 mm) at three sites: Norwich background, Cambridge intermediate, London kerbside. For compared sites, NO2 measured by acrylic samplers was significantly higher than for equivalent quartz samplers. For quartz samplers [NO2]mean was only just above the monitor at Norwich and London; sampler/monitor NO2 = 1.04 (P = 0.59) and 1.01(P = 0.76), respectively. For acrylic samplers the order of [NO2]mean was 40 mm > 120 mm > 71 mm > or = 55 mm. Excepting 40 mm samplers, this accords with a chemical bias where co-diffusing NO and 03 molecules in longer tubes have more time to react to form excess NO2. Bias in 40 mm samplers is discussed. Eddy diffusion is negligible for standard samplers because [NO2]mean was equivalent for 55 mm and 71 mm acrylic samplers and close to monitor NO2 for 71 mm quartz tubes. Both studies showed that sampler accuracy was dependent on location. Significantly, overestimation was greatest (approximately 3-4 ppb) where the NO2 annual mean was approximately 20 ppb, close to the UK and EU air quality standard of 21 ppb.     

Multi-level screening of a proposed hazardous waste treatment and disposal facility site--a case study

A comprehensive environmental assessment (EA) is a pre-requisite before the site for developing a hazardous waste treatment and disposal facility (HWTDF) is selected. However, the resource limitations, especially for developing countries, often dictatethat the detailed EA be restricted to those sites, which are constraint free and have low hazard potentials. Thus, a preliminary screening exercise for assessing the suitability ofsite for developing the HWTDF needs to be carried out to avoid huge costs involved in detailed EA. While screening a HWTDF site,various factors such as present land use, ecologically sensitiveareas, geology and hydrogeology of the area, the quality and quantity of wastes, engineered safeguards, and the operationalprocedures that need to be adopted, are required to be addressed. In this paper, a multi-level screening criteria employing RemoteSensing, Constraint Mapping, Groundwater Pollution Potential Index (DRASTIC Index), and the Site Ranking was used to assess the suitability of a proposed site for the development of HWTDF.The study helped to identify various constraints at the proposedsite and their significance on the development of the HWTDF.     

Monitoring of Seasonal Vegetables for Pesticide Residues

Market samples (60) of six seasonal vegetables were monitoredduring 1996–1997 to determine the magnitude of pesticidalcontamination. The estimation of insecticide residuesrepresenting four major chemical groups i.e. organochlorine,organophosphorous, synthetic pyrethroid and carbamate, was doneby adopting a multiresidue analytical technique employingGC-ECD and GC-NPD systems with capillary columns. The testedsamples showed 100% contamination with low but measurableamounts of residues. Among the four chemical groups, theorganophosphates were dominant followed by organochlorines,synthetic pyrethroids and carbamates. About 23% of the samplesshowed contamination with organophosphorous compounds abovetheir respective MRL values. More extensive studies coveringdifferent regions of Haryana state are suggested to get a clearidea of the magnitude of vegetable contamination with pesticideresidues.     

The influence of metallurgy on the formation of welding aerosols

Recent research has indicated that insoluble ultrafine aerosols (ie., particles whose physical diameters are less than 100 nm) may cause adverse health effects due to their small size, and that toxicological response may be more appropriately represented by particle number or particle surface area. Unfortunately, current exposure criteria and the associated air-sampling techniques are primarily mass-based. Welding processes are high-temperature operations that generate substantial number concentrations of ultrafine aerosols. Welding aerosols are formed primarily through the nucleation of metal vapors followed by competing growth mechanisms such as coagulation and condensation. Experimental results and mathematical tools are presented to illustrate how welding metallurgy influences the chemical aspects and dynamic processes that initiate and evolve the resultant aerosol. This research suggests that a fundamental understanding of metallurgy and aerosol physics can be exploited to suppress the formation of undesirable chemical species as well as the amount of aerosol generated during a welding process.     

Should foliar cadmium concentrations be expressed on a dry weight or dry ash weight basis?

Foliar analysis is a valuable tool for evaluating the pollution status of forests. However, the use of foliar diagnosis in large-scale surveys is a complicated process owing to the high variability within the crown. The method used to express foliar concentrations has often been found to diminish the variability. The effect of the method used to express element concentrations on the spatial variability of cadmium (Cd) in the leaves of crack willow (Salix fragilis L.) was investigated by sampling the leaves of one willow at 292 locations in the crown, each sampling location having a volume of 0.027 m3 (0.3 m x 0.3 m x 0.3 m). Cadmium showed a distinct spatial trend in the crown of the tree. Concentrations as low as 2.4 mg kg(-1) dry weight (DW) or 23.1 mg kg(-1) dry ash weight (DAW) were obtained in the top of the crown, and 10.6 mg kg(-1) DW or 73.0 mg kg(-1) DAW in the bottom of the crown. The lower relative standard deviation and weaker correlation with the sampling height support the use of DAW in large-scale surveys especially. The lower variability of the DAW Cd concentration makes this variable less sensitive to fluctuations caused by differences in growing conditions and sampling methodology. However, the majority of publications in this field report metal concentrations on a DW basis. Therefore, the restrictions set on the use of results expressed on a DAW basis in large-scale surveys of foliar metal concentrations have to be offset against the advantages offered by a reduction of the variability in metal concentrations.     

Preliminary air pollution monitoring in San Miguel, Buenos Aires

Passive diffusion samplers were employed in San Miguel(Buenos Aires Metropolitan Area) for a preliminary airpollution monitoring. The highest loads were observedin downtown, compared with an urban background site.Total suspended particulate matter (TSPM) varied from0.257 to 0.033 mg cm^-2 month^-1; dust was examinedfor particle nature and size distribution. A similartrend was observed for nitrogen dioxide (NO₂) andTSPM spatial distribution, suggesting that traffic isthe major pollution source. Sulphur dioxide (SO₂)values were low and rather homogeneous. Levels for theinvestigated pollutants are below EPA's guide linevalues. Geographic (flat area, near to Rio de LaPlata) and climatologic factors (rainfalls andvariable wind directions) contribute to disperse pollutants.     

Cadmium and Lead Levels in Fish (Tilapia Nilotica) Tissues as Biological Indicator for Lake Water Pollution

Cadmium and lead were determined in different tissues (muscle,gill, stomach, intestine, liver, vertebral column and scales) of Tilapia nilotica from the High Dam Lake, Aswan (Egypt) to assess the lake water pollution with those toxic metals. Fish samples were chosen from different ages and weights to be analyzed along with samples of the aquatic plant(Najas armeta), sediment and lake water.The results showed that cadmium and lead concentrations were higher in fish scales and vertebral column than in the other parts of the fish. Cadmium and lead levels in High Dam lake water and fish (Tilapia nilotica) were a result of the pollution which uptakes from aquatic plants, sediments andgasoline containing lead that leaks from fishery boats. Tilapia nilotica fish was used as a good bio-assay indicator for the lake pollution with cadmium and lead. The fish musclesin this study were in the safety baseline levels for man consumption.     

Collaborative study to improve the quality control of rare earth element determinations in environmental matrices

In order to control the quality of rare earth determinations in environmental matrices, the Standards, Measurements and Testing Programme (formerly Community Bureau of Reference, BCR) of the European Commission has started a project, the final aim of which is to certify four types of matrices (tuna muscle, mussel tissue, aquatic plant and estuarine sediment) for their contents of a range of rare earth elements (Sc, Y and the lanthanides: La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu). The elements U and Th were added to the study. The first part of this project consisted of an interlaboratory study which aimed to test the feasibility of preparation of environmental reference materials and to detect and remove most of the pitfalls observed in rare earth determinations. This paper presents the preparation of the four matrices for the intercomparison study and for the candidate reference material. The main results are presented of the interlaboratory study that was carried out prior to the certification campaign. This collaborative trial is the first attempt ever carried out at this scale to evaluate the state-of-the-art of rare earth determinations in the environment. Its impact on the improvement of chemical measurements will have positive effects on the comparability of data necessary for environmental monitoring.     

The extraction of aged polycyclic aromatic hydrocarbon (PAH) residues from a clay soil using sonication and a Soxhlet procedure: a comparative study

A sonication method was compared with Soxhlet extraction for recovering polycyclic aromatic hydrocarbons (PAH) from a clay soil that had been contaminated with tar materials for several decades. Using sonication over an 8 h extraction period, maximum extraction of the 16 US EPA priority PAH was obtained with dichloromethane (DCM)-acetone (1 + 1). The same procedure using hexane-acetone (1 + 1) recovered 86% of that obtained using DCM-acetone (1 + 1). PAH recovery was dependent on time of extraction up to a period of 8 h. The sonication procedure showed that individual PAH are extracted at differing rates depending on the number of fused rings in the molecule. Soxhlet extraction [with DCM-acetone (1 + 1)] over an 8 h period recovered 95% of the PAH removed by the sonication procedure using DCM-acetone (1 + 1), indicating that rigorous sonication can achieve PAH recoveries similar to those obtained by Soxhlet extraction. The lower recovery with the Soxhlet extraction was explained by the observed losses of the volatile PAH components after 1-4 h of extraction. The type of solvent used, the length of time of extraction and extraction method influenced the quantification of PAH in the soil. Therefore, the study has implications for PAH analyses in soils and sediments, and particularly for contaminated site assessments where the data from commercial laboratories are being used. The study emphasizes the importance of establishing (and being consistent in the application of) a vigorous extraction, particularly for commercial laboratories that handle samples of soil in batches (at different times) from a single site investigation or remediation process. The strong binding of PAH to soil, forming aged residues, has significant implications for extraction efficiency. This paper illustrates the problem of the underestimation of PAH using the US EPA method 3550, specifically where a surrogate spike is routinely employed and the efficiency of the extraction procedure for aged residues is unknown. The implications of this study for environmental monitoring, particularly where numerous batches of samples from a single site assessment or remediation program are submitted to commercial laboratories, is that it would be advisable for these laboratories to check their existing method's extraction efficiencies by conducting a time course sonication extraction on their particular soil to determine the optimum extraction time.     

Modeling rhizofiltration: heavy-metal uptake by plant roots

The discovery of phytoaccumulation potential of plant species has led to its application for remediation of heavy-metal-contaminated soil and wastewater, which is termed as phytoextraction/rhizofiltration. For prediction, analysis, planning and cost-effective design of such systems, mathematical models not only are used as a screening tool but also provide optimal parameters like harvesting time, irrigation schedule, etc. Several laboratory and field scale studies have been carried out in the past, and mathematical expressions have been developed by various researchers for different phenomena like metal adsorption in soil, plant root growth with time, moisture and metal uptake by plant root, moisture movement in unsaturated zone, soil moisture relationship, etc. The complete design of any such phytoremediation program would require the knowledge of behavior of heavy-metal movement in soil, water and plant root system. In this paper, a model for simulating heavy-metal dynamics in soil, water and plant root system is developed and discussed. The governing non-linear partial differential equation is solved numerically by implicit finite difference method using Picard's iterative technique, and the formulation has been illustrated using a characteristic example. The source code is written in MATLAB.