Development and application of long-term sublethal whole sediment tests with Arenicola marina and Corophium volutator using Ivermectin as the test compound

Short-term whole sediment tests using the amphipod Corophium volutator and the polychaete Arenicola marina are now routinely used in Europe to assess the acute toxicity of marine sediments. However, there is still a need to develop longer-term assays which measure effects on sublethal endpoints that are more relevant to predicting impacts at the population level. The effect of increasing exposure times and measuring additional endpoints such as growth, on the sensitivity of these assays was investigated. The test compound used was the chemotherapeutant Ivermectin (IVM), used in aquaculture to treat sea lice infestations. IVM was found to be acutely toxic to both test organisms. Extending the lugworm test to 100 days increased sensitivity of survival by a factor of three; a significant reduction in casting rate was observed at concentrations an order of magnitude lower. This assay shows potential for detecting the sublethal effects of low concentrations of sediment contaminants. Increasing the exposure time did not seem to affect the sensitivity of the amphipod, but further method development is required.     

Real time remote monitoring of air pollutants and their online transmission to the web using internet protocol

Recent advances in both information and sensor technologies have enabled the development of Real Time Remote Monitoring (RTRM) capabilities for environmental management. An online and real time remote monitoring system for air pollution has been designed and installed at a traffic police station at Punjagutta in Hyderabad, India. The system is optimized using electrochemical sensors and a real time particulate matter analyzer. The system also monitors meteorological parameters such as temperature, humidity, rainfall, barometric pressure, wind speed and wind direction. The system periodically monitors both pollution and meteorological parameters at pre- programmed intervals of hr during peak periods and 1 hr during non peak periods of the day and continuously uploads to a predestinated web site (www.appcb.org/home.htm) using File Transfer Protocol. The web site renders a quick, simple and graphical display of air pollution levels and meteorological parameters and their significance to humans. The present paper highlights design considerations of a pollution monitoring system, system hardware and software requirements and practical limitations and future directions for real time remote monitoring of air pollution.     

Concentrations of cadmium and lead heavy metals in Dardanelles seawater

Cadmium and lead were determined simultaneously in seawater by differential pulse stripping voltammetry (DPSV) preceded by adsoptive collection of complexes with 8-hydroxyquinoline (oxine) on to a hanging mercury drop electrode (HMDE). In preliminary experiments the optimal analytical condition for oxine concentration was found to be 2.10⁻⁵ M, at pH 7.7, the accumulation potential was −1.1 V, and the initial scannig potential was −0.8 V. The peak potentials were found −0.652 V for Cd and −0.463 V for Pb At the 60 s accumalation time. The limit of detection (LOD) and limit of quantitatification (LOQ) were found to be by voltammetry as 0.588 and 1.959 μg l⁻¹ (RSD, 5.50%) for Cd and 0.931 and 3.104 μg l⁻¹ (RSD, 4.10%) for Pb at 60 s stirred accumulation time respectively. In these conditions the most of the seawater samples are amenable for direct voltammetric determination of cadmium and lead using a HMDE. An adsorptive stripping mechanism of the electrode reaction was proposed. For the comparison, seawater samples were also analysed by ICP-atomic emission spectrometry method (ICP-AES). The applied voltammetric technique was validated and good recoveries were obtained.     

Serial Correlation and Inter-annual Variability in Relation to the Statistical Power of Monitoring Schemes to Detect Trends in Fish Populations

We studied the effects of inter-annual variability and serial correlation on the statistical power of monitoring schemes to detect trends in biomass of bream (Abramis brama) in Lake Veluwemeer (The Netherlands). In order to distinguish between 'true' system variability and sampling variability we simulated the development of the bream population, using estimates for population structure and growth, and compared the resulting inter-annual variabilities and serial correlations with those from field data. In all cases the inter-annual variability in the field data was larger than in simulated data (e.g. for total biomass of all assessed bream sigma = 0.45 in field data, and sigma = 0.03-0.14 in simulated data) indicating that sampling variability decreased statistical power for detecting trends. Moreover, sampling variability obscured the inter-annual dependency (and thus the serial correlation) of biomass, which was expected because in this long-lived population biomass changes are buffered by the many year classes present. We did find the expected serial correlation in our simulation results and concluded that good survey data of long-lived fish populations should show low sampling variability and considerable inter-annual serial correlation. Since serial correlation decreases the power for detecting trends, this means that even when sampling variability would be greatly reduced, the number of sampling years to detect a change of 15%.year(-1) in bream populations (corresponding to a halving or doubling in a six-year period) would in most cases be more than six. This would imply that the six-year reporting periods that are required by the Water Framework Directive of the European Union are too short for the existing fish monitoring schemes.     

Groundwater Pollution Around an Industrial Area in the Coastal Stretch of Maharashtra State, India

The main objective of this paper is to examine pollution threat, especially to the groundwater resources, around Tarapur industrial area (also called the Tarapur MIDC area) located on the Arabian Sea Coast in Thane District of Maharashtra State, India and suggest remedial measures that may also be relevant to other industrial areas on the Indian Sea Coast. One hundred and thirty one samples were collected from various sources, such as dugwells, borewells, dug-cum-borewells, effluent sumps, drainage channels (effluent channels), creeks and ocean, for chemical analyses. These analyses show that the area in general is characterized by hard water and high salinity hazard, possibly due to its proximity and hydraulic connection with the sea. Although the potability of groundwater is questionable in certain pockets, it is good enough for irrigation purposes at present. Low pH value and high heavy metal contents in the adjoining Muramba creek water is a matter of great concern and may be attributed to the indiscriminate disposal of industrial effluents to the drainage channels connecting the creek. Muramba Creek is well connected with the Arabian Sea, and there are evidences of seawater intrusion around this creek. Because of the fact that Muramba Creek is highly polluted, and is hydraulically connected with the dugwells and borewells surrounding the creek, it cannot be ruled out that the groundwater around this creek is susceptible to contamination. Unless measures are not taken immediately to stop the indiscriminate disposal of the solid wastes and liquid effluents in open ground and drainage channels, and measures are not taken to maintain the appropriate pH values at the effluent treatment facilities before their disposal, the problem would indeed be formidable one day, and it will be too late then for the authorities to take care of the resulting maladies. Few suggestions have been given for controlling and managing the industrial pollution around the Tarapur MIDC area. These suggestions are relevant to other industrial areas situated on the 7,000 km long Indian Sea Coast.     

Review of state of the art methods for measuring water in landfills

In recent years several types of sensors and measurement techniques have been developed for measuring the moisture content, water saturation, or the volumetric water content of landfilled wastes. In this work, we review several of the most promising techniques. The basic principles behind each technique are discussed and field applications of the techniques are presented, including cost estimates. For several sensors, previously unpublished data are given. Neutron probes, electrical resistivity (impedance) sensors, time domain reflectometry (TDR) sensors, and the partitioning gas tracer technique (PGTT) were field tested with results compared to gravimetric measurements or estimates of the volumetric water content or moisture content. Neutron probes were not able to accurately measure the volumetric water content, but could track changes in moisture conditions. Electrical resistivity and TDR sensors tended to provide biased estimates, with instrument-determined moisture contents larger than independent estimates. While the PGTT resulted in relatively accurate measurements, electrical resistivity and TDR sensors provide more rapid results and are better suited for tracking infiltration fronts. Fiber optic sensors and electrical resistivity tomography hold promise for measuring water distributions in situ, particularly during infiltration events, but have not been tested with independent measurements to quantify their accuracy. Additional work is recommended to advance the development of some of these instruments and to acquire an improved understanding of liquid movement in landfills by application of the most promising techniques in the field.     

Ignition and burning rates of segregated waste combustion in packed beds

Recent developments in national recycling and re-use programmes for municipal waste have led to segregation of an increasing proportion of waste to enhance material recovery. Several of the segregated streams contain materials that can not viably be re-used or recycled but can be used for energy recovery. In this study, the combustion of cardboard and waste wood was investigated in a small-scale packed bed reactor in order to provide fundamental data for the design/operation of moving bed furnaces. Key parameters of combustion including the ignition and burning rates were evaluated for various air flowrates and compared to the modelling results. Two successive stages of combustion were identified for both samples: the propagation of ignition front into the bed and combustion of the fuel above the ignition front. The burning rate of cardboard reached a peak of about 300 kg/m(2)h at the air flowrate of 936 kg/m(2)h and decreased at higher air flowrates. For waste wood, both the ignition and burning rates increased in the tested range of the air flowrate up to 702 kg/m(2)h, of which the values were very close to those for the cardboard. The model prediction was in good agreement with the test results for waste wood. However, the burning rate for cardboard was under-predicted due to strongly irregular shapes of the fuel.     

Use of inert C&D materials for seawall foundation: quality control measures

The technical viability of using inert construction and demolition (C&D) materials for the construction of seawall and breakwater foundations has been established by laboratory testing of the materials, numerical analysis of foundation stability, and a pilot field-scale engineering performance evaluation. However, quality control measures are still required so that only suitable materials are used for seawall and breakwater foundation construction. The development of different quality control measures for different site conditions is presented in this paper. The rationale, practicality, and implementation of these quality control measures are also discussed.     

Pilot installation for the thermo-chemical characterisation of solid wastes

The increasing production and the large variety of wastes require operators of thermal treatment units to continuously adapt the installations or the functioning parameters to the different physical and chemical properties of the wastes. Usually, the treated waste is encountered in the form of heterogeneous mixtures. The classical tests such as thermogravimetry and calorimetric bomb operate component by component, separately. In addition to this, they can analyse only small quantities of waste at a time (a few grams). These common tests are necessary but insufficient in the global waste analysis in the view further thermal treatment. This paper presents an experimental installation, which was designed and built at the CNRS Science Division, Department of Industrial Methods, Compiègne University of Technology, France. It allows the determination of waste thermal and chemical properties by means of thermal treatment. Also, it is capable of continuously analysing significant quantities of waste (up to 50kg/h) as compared to the classical tests and it can work under various conditions: The installation reproduces the process conditions from incinerators or pyrolysis reactors. It also provides complete information on the kinetics of the waste thermal degradation and on the pollutant emissions. Using different mixtures of components present in the municipal solid waste and also in the reconstituted MSW samples, we defined a series of criteria for characterising waste behaviour during the stages of the main treatment process such as: feeding, devolatilisation/oxidation, advancement, solid residue evacuation, and pollutants emission.     

Assessment of medical wastes management practice: a case study of the northern part of Jordan

This study includes a survey of the procedures available, techniques, and methods of handling and disposing of medical waste at medium (between 100 and 200 beds) to large (over 200 beds) size healthcare facilities located in Irbid city (a major city in the northern part of Jordan). A total of 14 healthcare facilities, including four hospitals and 10 clinical laboratories, serving a total population of about 1.5 million, were surveyed during the course of this research. This study took into consideration both the quantity and quality of the generated wastes to determine generation rates and physical properties. Results of the survey showed that healthcare facilities in Irbid city have less appropriate practices when it comes to the handling, storage, and disposal of wastes generated in comparison to the developed world. There are no defined methods for handling and disposal of these wastes, starting from the personnel responsible for collection through those who transport the wastes to the disposal site. Moreover, there are no specific regulations or guidelines for segregation or classification of these wastes. This means that wastes are mixed, for example, wastes coming from the kitchen with those generated by different departments. Also, more importantly, none of the sites surveyed could provide estimated quantities of waste generated by each department, based upon the known variables within the departments. Average generation rates of total medical wastes in the hospitals were estimated to be 6.10 kg/patient/day (3.49 kg/bed/day), 5.62 kg/patient/day (3.14 kg/bed/day), and 4.02 kg/patient/day (1.88 kg/bed/day) for public, maternity, and private hospitals, respectively. For medical laboratories, rates were found to be in the range of 0.053-0.065 kg/test-day for governmental laboratories, and 0.034-0.102 kg/test-day for private laboratories. Although, based on the type of waste, domestic or general waste makes up a large proportion of the waste volume, so that if such waste is not mixed with patient derived waste, it can be easily handled. However, based on infections, it is important for healthcare staff to take precautions in handling sharps and pathological wastes, which comprises only about 26% of the total infectious wastes. Statistical analysis was conducted to develop mathematical models to aid in the prediction of waste quantities generated by the hospitals studied, or similar sites in the city that are not included in this study. In these models, the number of patients, number of beds, and hospital type were determined to be significant factors on waste generation. Such models provide decision makers with tools to better manage their medical waste, given the dynamic conditions of their healthcare facilities.