High frequency monitoring of the coastal marine environment using the MAREL buoy

The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.     

Kinetics of Biotransformation of 2,4-Dichlorophenol using UASB-Reactor

Chlorophenol compounds are environmental pollutants that are both anthropogenic and xenobiotics. Some of these chemicals are carcinogens and are both toxic to a number biochemical processes. Biotransformation of 2,4-dichlorophenol (2,4-DCP) was studied in the presence of glucose on an upflow anaerobic sludge blanket reactor (UASB) using mixed culture. A continuously operated UASB reactor was employed using mixed synthetic wastewater. Results obtained from the 1.8 L volume capacity UASB reactor were subjected to kinetic evaluation constants. Results indicate that the degradation of 2,4-DCP in the presence of glucose was strongly influenced by the concentration of the compound. High degradation levels were observed when the concentration of 2,4-DCP was in the range of 50-150 mg L(-1). Concentrations of 2,4-DCP above 160 mg L(-1) were toxic to microbes even in the presence of glucose. The maximum degradation of 2,4-DCP was found to be 70.4% when initial concentration of 2,4-DCP was 124 mg L(-1) and glucose concentration of 500 mg L(-1) at hydraulic retention time of 13.2 hr. The biodegradation followed first order reaction kinetics with a rate constant (K) of 0.67, Vmax of 0.244 kg m(-3) day(-1), Ks of 0.117 kg m(-3) day(-1) and correlation coefficient of 0.766.     

Total versus inhalable sampler comparison study for the determination of asphalt fume exposures within the road paving industry

Exposure to asphalt fumes has a threshold limit value (TLV of 0.5 mg m(-3) (benzene extractable inhalable particulate) as recommended by the American Conference of Governmental Industrial Hygienists (ACGIH). This reflects a recent change (2000) whereby two variables are different from the previous recommendation. First is a 10-fold reduction in quantity from 5 mg m(-3) to 0.5 mg m(-3). Secondly, the new TLV specifies the "inhalable" fraction as compared to what is presumed to be total particulate. To assess the impact of these changes, this study compares the differences between measurements of paving asphalt fume exposure in the field using an "inhalable" instrument versus the historically used 'total' sampler. Particle size is also examined to assist in the understanding of the aerodynamic collection differences as related to asphalt fumes and confounders. Results show that when exposures are limited to asphalt fumes, a 1:1 relationship exists between samplers, showing no statistically significant differences in benzene soluble matter (BSM). This means that for the asphalt fume ACGIH TLV, the 'total' 37-mm sampler is an equivalent method to the "inhalable" method, referred to as IOM (Institute of Occupational Medicine), and should be acceptable for use against the TLV. However, the study found that when confounders (dust or old asphalt millings) are present in the workplace, there can be significant differences between the two samplers' reported exposure. The ratio of IOM/Total was 1.37 for milling asphalt sites, 1.41 for asphalt paving over granular base, and 1.02 for asphalt over asphalt pavements.     

Monitoring of Pesticidal Contamination of Farmgate Vegetables from Hisar

Analysis of 84 farm gate samples of seasonal vegetables carried out on GC-ECD and GC-NPD systems equipped with capillary columns by using a multi residue analytical technique revealed that 26% samples contained residues above MRL values. The contamination was mainly with organophosphates followed by synthetic pyrethroids and organochlorines. Among organophosphates, residues of monocrotophos, quinalphos and chlorpyriphos exceeded the MRL value in 23% samples. Residues of monocrotophos were higher than MRL value in 3 samples of brinjal and one sample each of okra, cauliflower and smooth gourd, of chlorpyriphos in 3 samples of cauliflower and 8 of cabbage and of quinalphos in one sample each of okra and cauliflower. Among synthetic pyrethroids, cypermethrin was the major contaminant and its residue exceeded the MRL value in one sample each of brinjal, okra and cucumber. Only aldicarb among the carbamates was detected in potato. The residues of some organochlorines, i.e. HCH, DDT and endosulfan were found in all the samples but did not exceed the tolerence limit.     

Evaluation of forest nutrition based on large-scale foliar surveys: are nutrition profiles the way of the future?

This paper introduces the use of nutrition profiles as a first step in the development of a concept that is suitable for evaluating forest nutrition on the basis of large-scale foliar surveys. Nutrition profiles of a tree or stand were defined as the nutrient status, which accounts for all element concentrations, contents and interactions between two or more elements. Therefore a nutrition profile overcomes the shortcomings associated with the commonly used concepts for evaluating forest nutrition. Nutrition profiles can be calculated by means of a neural network, i.e. a self-organizing map, and an agglomerative clustering algorithm with pruning. As an example, nutrition profiles were calculated to describe the temporal variation in the mineral composition of Scots pine and Norway spruce needles in Finland between 1987 and 2000. The temporal trends in the frequency distribution of the nutrition profiles of Scots pine indicated that, between 1987 and 2000, the N, S, P, K, Ca, Mg and Al decreased, whereas the needle mass (NM) increased or remained unchanged. As there were no temporal trends in the frequency distribution of the nutrition profiles of Norway spruce, the mineral composition of the needles of Norway spruce needles subsequently did not change. Interpretation of the (lack of) temporal trends was outside the scope of this example. However, nutrition profiles prove to be a new and better concept for the evaluation of the mineral composition of large-scale surveys only when a biological interpretation of the nutrition profiles can be provided.     

Pool of Dust Particles over the Asian Continent: Balloon-borne Optical Particle Counter and Ground-based Lidar Measurements at Dunhuang, China

Measurements of aerosols were made in 2001 and 2002 at Dunhuang (40 degrees 00'N, 94 degrees 30'E), China to understand the nature of atmospheric particles over the desert areas in the Asian continent. Balloon-borne measurements with an optical particle counter suggested that particle size and concentration had noticeable peaks in super micron size range not only in the boundary mixing layer but also in the free troposphere. Super-micron particle concentration largely decreased in the mid tropopause (from 5 to 10 km; above sea level, a.s.l.). Lidar measurements made during August 2002 at Dunhuang suggested the possibility that mixing of dust particles occurred from near the ground to about 6 km even under calm weather conditions, and a large depolarization ratio of particulate matter was found in the aerosol layer. The top of the aerosol layer was found at heights of nearly 6 km (a.s.l.). It is strongly suggested that nonspherical dust particles (Kosa particles) frequently diffused in the free atmosphere over the Taklamakan desert through small-scale turbulences and are possible sources of dust particles of weak Kosa events that have been identified in the free troposphere not only in spring but also in summer over Japanese archipelago. Electron microscopic experiments of the particles collected in the free troposphere confirmed that coarse and nonspherical particles observed by the mineral particle were major components of coarse mode (diameter larger than 1 microm) below about 5 km over Dunhuang, China.     

Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.