Assessment of internal condition of waste in a roofed landfill

Recently, roofed landfills have been gaining popularity in Japan. Roofed landfills have several advantages over non-roofed landfills such as eliminating the visibility of waste and reducing the spread of offensive odours. This study examined the moisture balance and aeration conditions, which promote waste stabilisation, in a roofed landfill that included organic waste such as food waste. Moisture balance was estimated using waste characterization and the total amount of landfilled waste. Internal conditions were estimated based on the composition, flux, and temperature of the landfill gas. Finally, in situ aeration was performed to determine the integrity of the semi-aerobic structure of the landfill.With the effects of rainfall excluded, only 15% of the moisture held by the waste was discharged as leachate. The majority of the moisture remained in the waste layer, but was less than the optimal moisture level for biodegradation, indicating that an appropriate water spray should be administered. To assess waste degradation in this semi-aerobic landfill, the concentration and flow rate of landfill gas were measured and an in situ aeration test was performed. The results revealed that aerobic biodegradation had not occurred because of the unsatisfactory design and operation of the landfill.     

Development of non-invasive fetal DNA diagnosis from maternal blood

Several attempts have been made to detect and retrieve fetal nucleated cells including nucleated erythrocytes (NRBCs), leukocytes, and trophoblasts in maternal blood. We have recently developed a new method for non-invasive fetal DNA diagnosis from maternal blood. Peripheral blood granulocytes including NRBCs were isolated by a discontinuous density gradient method using Percoll (Pharmasia). NRBCs were found and retrieved at a single cell level using a micromanipulator under a microscope. To determine whether the origin of the NRBCs was maternal or fetal, the NRBCs were analysed by polymerase chain reaction (PCR) amplification to determine the presence of a Y-chromosome-specific repeat sequence in mothers carrying male fetuses. We were successful in predicting fetal sex accurately in 10 out of 11 samples taken from maternal blood. This new technique opens up fetal DNA diagnosis from maternal blood during the first trimester of pregnancy to the whole population because there is no risk to the fetus or the mother.     

Update of daily intake of PCDDs, PCDFs, and dioxin-like PCBs from food in Japan

Total diet study (TDS) samples of 14 food groups from 16 locations in Japan, collected in 1999 and 2000, were analyzed for polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), and dioxin-like polychlorinated biphenyls (dioxin-like PCBs) to estimate the update of daily intake of these contaminants from food. The mean daily intake of toxic equivalency (TEQ) for an adult weighing 50 kg, calculated at non-detected isomer concentrations equal to zero (ND=0), was estimated to be 2.25 pg TEQ/kg b.w./day. When non-detected isomer concentrations are assumed to be equal to half of the limits of detection (ND=1/2 LOD), the mean daily intake was estimated to be 3.22 pg TEQ/kg b.w./day. These values were below the tolerable daily intake (TDI) of 4 pg TEQ/kg b.w. for PCDD/Fs and dioxin-like PCBs set in Japan. In both the estimates, the mean daily intakes were highest from fish and shellfish (76.9% at ND=0 and 53.9% at ND=1/2 LOD of the total TEQs), followed by those from meat and eggs (15.5% at ND=0 and 11.7% at ND=1/2 LOD of the total TEQs). Congener specific data revealed that these total TEQ levels were dominated by 1,2,3,7,8-PeCDD, 2,3,4,7,8-PeCDF and 3,3^′,4,4^′,5-PeCB in each case (71.7% at ND=0 and 63.1% at ND=1/2 LOD of the total TEQs). The dioxin-like PCBs (non-ortho and mono-ortho PCBs) accounted for about 50% of these total TEQs. These data will be very useful in the risk assessment of PCDD/Fs and dioxin-like PCBs from food in Japan.     

Leaching behaviour of elements and evaluation of pre-treatment methods for municipal solid waste incinerator residues in column leaching tests.

Two new pre-treatment methods (water-washing/carbonation and carbonation/phosphate stabilization) of municipal solid waste (MSW) incinerator residues were evaluated by column leaching tests under aerobic conditions and anaerobic conditions (which were changed to aerobic conditions after 10 months). A mixture of bottom ash and fly ash (5:1 ratio) was pre-treated using each method. Shredded incombustible residues (SIR) were added to each ash preparation in proportions similar to the ratios present in landfills. For comparison, landfill wastes typical of Japan, namely, a mixture of bottom ash, chelating-pre-treated fly ash, and SIR, were also examined. Leachate samples were collected periodically and analysed over a 15-month period. When compared with chelating pretreatment, both water-washing/carbonation and carbonation/ phosphate stabilization reduced the leaching of Pb, Al, and Cu by about one to two orders of magnitude. Moreover, the initial concentrations of Ca and Pb in leachates from column of water-washing/carbonation were 56-57% and 84-96% less than those from the column of carbonation/phosphate stabilization. Therefore, water-washing/carbonation was considered to be a promising approach to obtain early waste stabilization and to reduce the release of heavy metals to near-negligible levels. The leaching behaviour of elements was also discussed.     

Comparison of mass balance, energy consumption and cost of composting facilities for different types of organic waste

Mass balance, energy consumption and cost are basic pieces of information necessary for selecting a waste management technology. In this study, composting facilities that treat different types of organic waste were studied by questionnaire survey and via a chemical analysis of material collected at the facilities.The mass balance was calculated on a dry weight basis because the moisture content of organic waste was very high. Even though the ratio of bulking material to total input varied in the range 0-65% on a dry basis, the carbon and ash content, carbon/nitrogen ratio, heavy metal content and inorganic nutrients in the compost were clearly influenced by the different characteristics of the input waste. The use of bulking material was not correlated with ash or elemental content in the compost. The operating costs were categorised into two groups. There was some economy of scale for wages and maintenance cost, but the costs for electricity and fuel were proportional to the amount of waste. Differences in operating costs can be explained by differences in the process characteristics.     

Simple removal of dioxins by injecting combustion gas into water

A simple, low-cost method for suppression of dioxins/furans (hereinafter referred to as dioxins) is required because many middle- and, especially, small-scale incinerators have fallen into disuse or have been dismantled because of the high running and system costs of measures for the suppression of dioxins. Therefore, the purpose of the present study was to develop a simple removal method for dioxins from combustion gas and to evaluate the basic removal rate of dioxins. The removal method for suspended matter in a gas mixture (cold model) and dioxins in exhaust gases (hot model) has been investigated by means of gas injection into water, the mechanism of which is that the suspended matter in the gas gathers at the gas–liquid interface. In the cold model, the removal ratio of fine particles (R_P) by gas injection into water was reproduced well by the following equation: R_P (%) = 100 × {1−exp(−0.8 · S_S · t_C)}, where S_S (cm²/cm³) is the specific surface area of bubbles and t_C (s) is the residence time of bubbles in water. The removal ratio of fine particles increased as the product S_s · t_C increased. In a hot model using the exhaust gas from combustion experiments of polyvinyl chloride, the removal ratio of dioxins (R_D) by injecting the exhaust gas into water was estimated by the following equation: R_D (%) = 100 × {1−exp(−0.8 · S_S · t_C · C_D0 ^0.07)}, where C_D0 [ng/cm³ (at standard temperature and pressure)] is the dioxins concentration in the exhaust gas before injection into water. R_D depends greatly on the specific surface area of bubbles and the residence time of the bubbles in water, and only weakly on the dioxins concentration in the exhaust gas. Injection of the exhaust gas into water has been shown to be effective and was evaluated as a simple method for the removal of dioxins from exhaust gas.