Using constant head step tests to determine hydraulic apertures in fractured rock

The initial step in the analysis of contaminant transport in fractured rock requires the consideration of groundwater velocity. Practical methods for estimating the average linear groundwater velocity (vˉ) in fractured rock require determination of hydraulic apertures which are commonly calculated by applying the cubic law using transmissivity (T) values and the number of hydraulically active fractures in the test interval. High-resolution, constant-head step injection testing of cored boreholes in a 100 m thick fractured dolostone aquifer was conducted using inflatable packers to isolate specific test intervals from the rest of the borehole. The steps in each test interval were gradually increased from very low to much higher injection rates. At smaller injection rates, the flow rate vs. applied pressure graph projects through the origin and indicates Darcian flow; non Darcian flow is evident at higher injection rates. Non-Darcian flow results in significantly lower calculated T values, which translates to smaller hydraulic aperture values. Further error in the calculated hydraulic aperture stems from uncertainty in the number of hydraulically active fractures in each test interval. This estimate can be inferred from borehole image and core logs, however, all of the fractures identified are not necessarily hydraulically active. This study proposes a method based on Reynolds number calculations aimed at improving confidence in the selection of the number of active fractures in each test interval.     

Hydrogen peroxide stabilization in one-dimensional flow columns

Rapid hydrogen peroxide decomposition is the primary limitation of catalyzed H(2)O(2) propagations in situ chemical oxidation (CHP ISCO) remediation of the subsurface. Two stabilizers of hydrogen peroxide, citrate and phytate, were investigated for their effectiveness in one-dimensional columns of iron oxide-coated and manganese oxide-coated sand. Hydrogen peroxide (5%) with and without 25 mM citrate or phytate was applied to the columns and samples were collected at 8 ports spaced 13 cm apart. Citrate was not an effective stabilizer for hydrogen peroxide in iron-coated sand; however, phytate was highly effective, increasing hydrogen peroxide residuals two orders of magnitude over unstabilized hydrogen peroxide. Both citrate and phytate were effective stabilizers for manganese-coated sand, increasing hydrogen peroxide residuals by four-fold over unstabilized hydrogen peroxide. Phytate and citrate did not degrade and were not retarded in the sand columns; furthermore, the addition of the stabilizers increased column flow rates relative to unstabilized columns. These results demonstrate that citrate and phytate are effective stabilizers of hydrogen peroxide under the dynamic conditions of one-dimensional columns, and suggest that citrate and phytate can be added to hydrogen peroxide before injection to the subsurface as an effective means for increasing the radius of influence of CHP ISCO.     

Contaminants in the coastal karst aquifer system along the Caribbean coast of the Yucatan Peninsula, Mexico

Intensive land development as a result of the rapidly growing tourism industry in the “Riviera Maya” region of the Yucatan Peninsula, Mexico may result in contamination of groundwater resources that eventually discharge into Caribbean coastal ecosystems. We deployed two types of passive sampling devices into groundwater flowing through cave systems below two communities to evaluate concentrations of contaminants and to indicate the possible sources. Pharmaceuticals and personal care products accumulated in the samplers could only have originated from domestic sewage. PAHs indicated contamination by runoff from highways and other impermeable surfaces and chlorophenoxy herbicides accumulated in samplers deployed near a golf course indicated that pesticide applications to turf are a source of contamination. Prevention and mitigation measures are needed to ensure that expanding development does not impact the marine environment and human health, thus damaging the tourism-based economy of the region.     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

A techno-economic comparison of fluidized bed gasification of two mixed plastic wastes

A comparison between the most promising design configurations for the industrial application of gasification based, plastics-to-energy cogenerators in the 2-6 MWe range is presented. A pilot scale bubbling fluidized bed air gasifier, having a feeding capacity of 100 kg/h, provided experimental data: the syngas complete composition, the characterization of the bed material, the entrained fines collected at the cyclone and the purge material from the scrubber. Mass and energy balances and material and substance flow analyses have been therefore drawn to assess and compare design solutions utilizing two mixed plastic wastes (MPW) obtained from separate collection of plastic packaging, after different levels of pre-treatments. The related techno-economic performances have been finally estimated on the basis of the manufacturer’s specifications. The study concludes that the MPW obtained after a very simple pre-treatment and fed to a gasifier coupled with a steam turbine is the solution that currently offers the higher reliability and provides the higher internal rate of return for the investigated range of electrical energy production.     

Targeted intervention strategies to optimise diversion of BMW in the Dublin, Ireland region

Urgent transformation is required in Ireland to divert biodegradable municipal waste (BMW) from landfill and prevent increases in overall waste generation. When BMW is optimally managed, it becomes a resource with value instead of an unwanted by-product requiring disposal. An analysis of survey responses from commercial and residential sectors for the Dublin region in previous research by the authors proved that attitudes towards and behaviour regarding municipal solid waste is spatially variable. This finding indicates that targeted intervention strategies designed for specific geographic areas should lead to improved diversion rates of BMW from landfill, a requirement of the Landfill Directive 1999/31/EC. In the research described in this paper, survey responses and GIS model predictions from previous research were the basis for goal setting, after which logic modelling and behavioural research were employed to develop site-specific waste management intervention strategies. The main strategies devised include (a) roll out of the Brown Bin (Organics) Collection and Community Workshops in Dún Laoghaire Rathdown, (b) initiation of a Community Composting Project in Dublin City (c) implementation of a Waste Promotion and Motivation Scheme in South Dublin (d) development and distribution of a Waste Booklet to promote waste reduction activities in Fingal (e) region wide distribution of a Waste Booklet to the commercial sector and (f) Greening Irish Pubs Initiative. Each of these strategies was devised after interviews with both the residential and commercial sectors to help make optimal waste management the norm for both sectors. Strategy (b), (e) and (f) are detailed in this paper. By integrating a human element into accepted waste management approaches, these strategies will make optimal waste behaviour easier to achieve. Ultimately this will help divert waste from landfill and improve waste management practice as a whole for the region. This method of devising targeted intervention strategies can be adapted for many other regions.     

制药废水有机污染物特性分析与处理

分析了某制药企业废水生物处理站进出水中有机污染物的相对分子质量分布和气相色谱—质谱图谱,提出了根据废水水质特性有针对性地确定制药废水处理工艺的新思路.实验结果表明:进出水中的有机污染物主要是相对分子质量小于1 000的物质,且主要来源于车间5排放的COD比重大、水量小的工段废水;采用旋转蒸馏预处理法处理车间5废水,可使...     

Indicator framework for sustainable production planning and controlling

Production facilities serve to transform raw materials into products, usually with the goal of achieving a designated output, in terms of quantity and quality, with the minimum of cost and labour. With the aid of production planning and controlling (PPC) systems, raw material inputs, and labour can be planned to achieve a determined output of products. In general, the role of environmental and social aspects is neglected in production planning processes. Because of the growing pressure from politics and customers, sustainable production of products is becoming more important. One possibility for supporting sustainable manufacturing is, to integrate sustainable aspects in the production planning process. This paper presents input and output information for current PPC systems and discusses the need for additional information necessary for sustainable PPC. For this approach, a text review of cooperate social responsibility (CSR) reporting indicators provided by the GRI was performed. Based on the text review, an input-output model has been developed for conventional and another one for sustainable PPC systems. Through the comparison of the two input-output models, challenges and requirements for sustainable PPC systems have been defined as a basis for future work and analyses.