Reversibility of stemflow-induced soil acidification in Swedish beech forest

Stemwater running down the trunks of beech (Fagus sylvatica L.) has an acidifying effect on soil near the stem. The deposition of acidifying substances may be two to four times higher close to the stem compared to in the stand in general. To study reversibility of soil acidification, 72 stumps of beech trees were chosen from five different year classes of felling (3, 6, 9, 14-15, 25-30), representing the years when stemflow ceased to affect the soil. The H(+) concentration (pH KCl) in the topsoil (0-5 cm) differed between the distances 10-30 cm and 230-250 cm from the stumps, the soil close to the stem being more acid. The longer the time since felling the smaller the differences in H(+) concentration became. This reduction in soil acidity amounted to ca. 50% after 15 years, and only small further changes occurred over the next ten years. This indicates that soil may not recover fully from acidification, or does so at a rather slow rate after the initial 15 years of recovery.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

Analysing the sensitivity behaviour of two hydrology models

Recently, the New Morris Method has been presented as an effective sensitivity analysis tool for mathematical models. The New Morris Method estimates the sensitivity of an output parameter to a given set of input parameters (first-order effects) and the extent these parameters interact with each other (second-order effects). This method requires the specification of two parameters (runs and resolution) that control the sampling of the output parameter to determine its sensitivity to various inputs. The criteria for these parameters have been set on the analysis of a well-behaved analytical function (see Cropp and Braddock, Reliab. Eng. Syst. Saf. 78:77–83, 2002), which may not be applicable to other physical models that describe complex processes. This paper will investigate the appropriateness of the criteria from (Cropp and Braddock, 2002) and hence the effectiveness of the New Morris Method to determine the sensitivity behaviour of two hydrologic models: the Soil Erosion and Deposition System and Griffith University Representation of Urban Hydrology. In the first case, this paper will separately analyse the sensitivity of an output parameter on a set of input parameters (first- and second-order effects) for each model and discuss the physical meaning of these sensitivities. This will be followed by an investigation into the sampling criteria by exploring the convergence of the sensitivity behaviour for each model as the sampling of the parameter space is increased. By comparing these trends to the convergence behaviour from Cropp and Braddock (2002), we will determine how well the New Morris Method estimates the sensitivity for each model and whether the sampling criteria are appropriate for these models. It will be shown that the New Morris Method can provide additional insight into the functioning of these models, and that, under a different metric, the sensitivity behaviour of these models does converge confirming the sampling criteria set by Cropp and Braddock.     

Diffusive sampling of methyl isocyanate using 4-nitro-7-piperazinobenzo-2-oxa-1,3-diazole (NBDPZ) as derivatizing agent

A diffusive sampling method for the determination of methyl isocyanate (MIC) in air is introduced. MIC is collected using a glass fiber filter impregnated with 4-nitro-7-piperazinobenzo-2-oxa-1,3-diazole (NBDPZ). The urea derivative formed is desorbed from the filter with acetonitrile and analyzed by means of high-performance liquid chromatography (HPLC) using fluorescence detection (FLD) with lambdaex = 471 nm and lambdaex = 540 nm. Additionally, a method was developed using tandem mass spectrometric (MS-MS) detection, which was performed as selected reaction monitoring (SRM) on the transition [MIC-NBDPZ + H]+ (m/z 307) to [NBDPZ + H]+ (m/z 250). The diffusive sampler was tested with MIC concentrations between 1 and 35 microg m(-3). The sampling periods varied from 15 min to 8 h, and the relative humidity (RH) was set from 20% up to 80%. The sampling rate for all 15 min experiments was determined to be 15.0 mL min(-1) (using HPLC-FLD) with a relative standard deviation of 9.9% for 56 experiments. At 80% RH, only 15 min sampling gave acceptable results. Further experiments revealed that humidity did not affect the MIC derivative but the reagent on the filter prior to and during sampling. The sampling rate for all experiments (including long term sampling) performed at 20% RH was found to be 15.0 mL min(-1) with a relative standard deviation of 6.3% (N = 42). The limit of quantification was 3 microg m(-3) (LC-MS-MS: 1.3 microg m(-3)) for 15 min sampling periods and 0.2 microg m(-3) (LC-MS-MS: 0.15 microg m(-3)) for 8 h sampling runs applying fluorescence detection.     

Quantification of protein adducts of hexahydrophthalic anhydride and methylhexahydrophthalic anhydride in human plasma

Hexahydrophthalic anhydride (HHPA) and methylhexahydrophthalic anhydride (MHHPA) are two highly allergenic compounds used in the chemical industry. A method was developed for quantification of protein adducts of HHPA and MHHPA in human plasma. The plasma was dialysed and the anhydrides were hydrolysed from the proteins at mild acidic conditions. The released hexahydrophthalic acid (HHP acid) and methylhexahydrophthalic acid (MHHP acid) were purified by reversed solid phase extraction followed by derivatisation with pentafluorobenzyl bromide. The derivatives were analysed using GC-MS in negative ion chemical ionisation mode with ammonia as moderating gas. As internal standards, deuterium labelled HHP and MHHP acids were used. The detection limits were 0.06 pmol mL(-1) plasma for HHP acid and 0.03 pmol mL(-1) plasma for MHHP acid. The between-day precisions for HHP acid were 18% at 0.3 pmol mL(-1) and 8% at 4 pmol mL(-1). For MHHP acid, the precisions were 13% at 0.3 pmol mL(-1) and 9% at 4 pmol mL(-1). There were strong correlations (r=0.94 for HHPA and 0.99 for MHHPA) between total plasma protein adduct concentrations and serum albumin adduct levels. Workers exposed to time-weighted average air levels of HHPA between < 1 and 340 microg m(-3) and between 2 and 160 microg m(-3) for MHHPA had plasma adduct levels between the detection limits of the methods and 8.40 and 19.0 pmol mL(-1), respectively.     

The influence of geometry and draught shields on the performance of passive samplers

Passive samplers provide an excellent opportunity to perform indicative measurements or establish a dense network of measuring sites. A drawback compared with conventional active measuring methods is the larger spread of results. This variation can, to a large extent, be attributed to the influence of temperature, sampler geometry and wind on sampling results. A proper design of sampler geometry and optimum choice of draught shield can reduce the influence of wind velocity on a badge type sampler to less than 10%. Wire mesh screens prove to be inadequate in damping turbulence. Filters give good results. Attention should be paid to the size and isolation value of the walls of the sampler to prevent thermal updrafts occurring within the sampler. Tube type samplers are less influenced by wind, provided that turbulence is prevented from influencing diffusion within the sampler.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

A combination of micro-porous membrane liquid-gas extraction and solid-phase trapping for ultra trace determination of benzene in urine

A method was developed for the determination of benzene in urine. The sample was pumped through the donor channel of a membrane extraction unit with a micro-porous membrane, separating the donor channel from an identical acceptor channel purged with nitrogen. The analyte reached the acceptor channel by diffusion through the membrane and was then swept by the carrier to a solid sorbent tube, where it was trapped. The analyte was subsequently thermally desorbed and analyzed by gas chromatography (GC) with mass selective detection (MS). After optimization, the recovery was close to quantitative, or 95%. Purging the membrane unit with pure water in between the samples eliminated any memory effects. The linearity was good in the concentration range examined (20-4000 ng l(-1)), with a correlation coefficient of 0.9996. The repeatability at 50 ng l(-1) and 400 ng l(-1) was 1.4% and 1.2%, respectively. The limit of detection was 12 ng l(-1) and the limit of quantification 35 ng l(-1). This enables assessment of benzene exposures of occupationally exposed subjects, of smokers and the majority of the general population. The developed method can be easily automated.     

Environmental quality control and environmental games

Conclusion  In this paper we have considered a specific environmental game emphasizing both control-prevention efforts and the propensity to pollute by a firm which adopts a given pollution abatement technology. A random payoff game was constructed and solved under a risk neutral assumption and quadratic utilities for both the firm and the environmental controller. The game thus defined, provides a wide range of interpretations and potential approaches for selecting a control-inspection policies to prevent environmental risks. There are of course many facets to this problem, which could be considered and have not been considered in sufficient depth. For example, more complex control mechanisms and liabilities, the effects of insurance and risk sharing, the application of cooperative efforts and subvention of pollution abatement investments (through tax incentives and their like), etc. have not been considered [5,7]. These are topics for further research. The basic presumption of this paper is that it is very difficult to fully enforce pollution prevention by firms, as a result, some controls are needed to ensure that firms be controlled so that appropriate efforts are carried.