Swine wastewater treatment in a two stage sequencing batch reactor using real‐time control

Abstract

A laboratory scale two‐stage sequencing batch reactor (TSSBR) was used to study the effectiveness of pH as a real‐time control parameter in swine wastewater treatment. A Ringlace media was inserted into the A/O (Anoxic/Oxic) reactor for bacteria immobilization. The TSSBR was subjected to three levels of organic loading. The pH and ORP (Oxidation Reduction Potential) patterns obtained were consistent with distinct features, enabling the real‐time control strategy to effectively set a flexible aeration time pending on influent concentration, hence resulting in flexible cycle time and HRT (Hydraulic Retention Time) for the system. The real‐time process ensured a removal efficiency of over 99% and 95%, respectively, for ammonia and TOC (Total Organic Carbon). For NO₃ ^‐‐N and PO₄ ^‐3, the run with influent TOC = 4,000 mg/L yielded the most efficient removal of 61% and 95%, respectively. Test results suggest that pH can be a viable tool for on‐line real‐time control of a biological treatment process.     

Treating solid dairy manure using microwave-enhanced advanced oxidation process

The microwave enhanced advanced oxidation process (MW/H₂O₂-AOP) was used to treat separated solid dairy manure for nutrient release and solids reduction. The MW/H₂O₂-AOP was conducted at a microwave temperature of 120°C for 10 minutes, and at three pH conditions of 3.5, 7.3 and 12. The hydrogen peroxide dosage at approximately 2 mL per 1% TS for a 30 mL sample was used in this study, reflecting a range of 0.53–0.75 g H₂O₂/g dry sludge. The results indicated that substantial quantities of nutrients could be released into the solution at pH of 3.5. However, at neutral and basic conditions only volatile fatty acids and soluble chemical oxygen demand could be released. The analyses on orthophosphate, soluble chemical oxygen demands and volatile fatty acids were re-examined for dairy manure. It was found that the orthophosphate concentration for untreated samples at a higher % total solids (TS) was suppressed and lesser than actual. To overcome this difficulty, the initial orthophosphate concentration had to be measured at 0.5% TS.     

Micronucleus frequency in sheep lymphocytes after in vitro exposure to fungicide tolylfluanid

The fungicide tolylfluanid (N - dichlorofluoromethylthio-N′, N - dimethyl - N - p - tolylsulfamide), was investigated by cytokinesis-block micronucleus assay. Tolylfluanid at the lowest concentration (1 × 10^{? 6}mol L^{? 1})did not influence significantly the frequency of micronuclei in sheep lymphocyte cultures in comparison with control (32.33 ± 3.51/1000 binucleated cells versus 30.33 ± 2.82/1000 binucleated cells in dimethylsulfoxide (DMSO) control, P = 0.44). Higher tolylfluanid concentrations (1 × 10^{? 4} and, 1 × 10^{? 5} mol L^{? 1}) resulted in a significant dose-dependent increase in the number of micronuclei in comparison with control (74.00 ± 13.00/1000 binucleated cells and 52.67 ± 10.12/1000 binucleated cells versus 30.33 ± 2. 82/1000 binucleated cells in DMSO control, P = 0.005 and 0.02, respectively, ANOVA followed by Tukey test P < 0.05). Many of the treated cells also possessed multiple micronuclei. Tolylfluanid did not affect the nuclear division index at all treatment concentrations. Our in vitro results thus demonstrate that tolylfluanid had a significant genotoxic effect at only the highest concentration tested.     

Microwave enhanced advanced oxidation process for treating dairy manure at low pH

This study investigated the treatment of dairy manure using the microwave enhanced advanced oxidation process (MW-AOP) at pH 2. An experimental design was developed based on a statistical program using response surface methodology to explore the effects of temperature, hydrogen peroxide dosage and heating time on sugar production, nutrient release and solids destruction. Temperature, hydrogen peroxide dosage and acid concentration were key factors affecting reducing sugar production. The highest reducing sugar yield of 7.4% was obtained at 160°C, 0 mL, 15 min heating time, and no H₂O₂ addition. Temperature was a dominant factor for an increase of soluble chemical oxygen demand (SCOD) in the treated dairy manure. The important factors for volatile fatty acids (VFA) production were microwave temperature and hydrogen peroxide dosage. Temperature was the most important parameter, and heating time, to a lesser extent affecting orthophosphate release. Heating time, hydrogen peroxide dosage and temperature were significant factors for ammonia release. There was a maximum of 96% and 196% increase in orthophosphate and ammonia concentration, respectively at 160°C, 0.5 mL H₂O₂ and 15 min heating time. The MW-AOP is an effective method in dairy manure treatment for sugar production, nutrient solubilisation, and solids disintegration.     

Effects of pen bedding and feeding high crude protein diets on manure composition and greenhouse gas emissions from a feedlot pen surface

Greenhouse gas (GHG) emissions from concentrated animal feeding operations vary by stage of production and management practices. The objective of this research was to study the effect of two dietary crude protein levels (12 and 16%) fed to beef steers in pens with or without corn stover bedding. Manure characteristics and GHG emissions were measured from feedlot pen surfaces. Sixteen equal-sized feedlot pens (19?×?23 m) were used. Eight were bedded approximately twice a week with corn stover and the remaining eight feedlot pens were not bedded. Angus steers (n = 138) were blocked by live weights (lighter and heavier) with 7 to 10 animals per pen. The trial was a 2?×?2 factorial design with factors of two protein levels and two bedding types (bedding vs. non bedding), with four replicates. The study was conducted from June through September and consisted of four ?28-day periods. Manure from each pen was scrapped once every 28 days and composite manure samples from each pen were collected. Air samples from pen surfaces were sampled in Tedlar bags using a Vac-U-Chamber coupled with a portable wind tunnel and analyzed with a greenhouse gas gas chromatograph within 24 hr of sampling. The manure samples were analyzed for crude protein (CP), total nitrogen (TN), ammonia (NH₃), total volatile fatty acid (TVFA), total carbon (TC), total phosphorus (TP), and potassium (K). The air samples were analyzed for methane (CH₄), carbon dioxide (CO₂), and nitrous oxide (N₂O) concentrations. The concentration of TN was significantly higher (p < 0.05) in manure from pens with cattle fed the high protein diets. The volatile fatty acids (VFAs) such as acetic, propionic, isobutyric, butyric, isovaleric, and valeric acids concentrations were similar across both treatments. There were no significant differences in pen surface GHG emissions across manure management and dietary crude protein levels.

Implications: Livestock manure produces odor and emits GHGs (CO₂, CH₄, and N₂O) at different stages of production and management practices that have significant environmental concerns. Thus, it is important to measure GHG contributions from different sources and develop appropriate mitigation strategies for minimizing GHG contribution from livestock production facilities. Two dietary protein levels (12 and 16%) fed to beef steers in pens with or without corn stover bedding were studied. The results indicated that dietary protein levels and bedding vs. no bedding had very little effect on GHG emissions and manure composition under open feedlot conditions in North Dakota climatic conditions and management practices.     

Phase II Allowances Allocations and an Assessment of the Allowance Market in the West

Title IV of the Clean Air Act Amendments of 1990 establishes a unique “market-based“ approach to reduce national electric utility sulfur dioxide (SO₂) emissions during the next century by about 10 million tons/year below the corresponding level in 1980. This program is designed to provide utility operators with the flexibility to achieve the applicable SO₂ emissions limitations (total tons) using the most cost-effective approach. However, in reality, it is unlikely that many utility operators would have such operational flexibility, especially in the case of plants located in the Western United States. This is due to the fact that these sources may also be subject to other more stringent provisions of the Act, such as to protect public health and visibility, which override the Title IV provisions.

This paper examines the Phase II allowance allocations for the utility units located in the 11 western states and assesses the potential impacts of the current federal/state air quality regulatory programs on the allowance market in the West. This analysis shows that, even after accounting for the projected population growth and the accompanying growth in electric power demand during the next decade, the West should have a surplus of allowances, especially if new regulations are initiated to further reduce SO₂ emissions, mainly for the purpose of improving visibility in Western Class I areas.     

Multiple-year black carbon measurements and source apportionment using Delta-C in Rochester,New York

Black carbon (BC), an important component of the atmospheric aerosol, has climatic, environmental, and human health significance. In this study, BC was continuously measured using a two-wavelength aethalometer (370 nm and 880 nm) in Rochester, New York, from January 2007 to December 2010. The monitoring site is adjacent to two major urban highways (I-490 and I-590), where 14% to 21% of the total traffic was heavy-duty diesel vehicles. The annual average BC concentrations were 0.76 μg/m³, 0.67 μg/m³, 0.60 μg/m³, and 0.52 μg/m³ in 2007, 2008, 2009, and 2010, respectively. Positive matrix factorization (PMF) modeling was performed using PM_2.5 elements, sulfate, nitrate, ammonia, elemental carbon (EC), and organic carbon (OC) data from the U.S. Environmental Protection Agency (EPA) speciation network and Delta-C (UVBC_370nm – BC_880nm) data. Delta-C has been previously shown to be a tracer of wood combustion factor. It was used as an input variable in source apportionment models for the first time in this study and was found to play an important role in separating traffic (especially diesel) emissions from wood combustion emissions. The result showed the annual average PM_2.5 concentrations apportioned to diesel emissions in 2007, 2008, 2009, and 2010 were 1.34 μg/m³, 1.25 μg/m³, 1.13 μg/m³, and 0.97 μg/m³, respectively. The BC conditional probability function (CPF) plots show a large contribution from the highway diesel traffic to elevated BC concentrations. The measurements and modeling results suggest an impact of the U.S Environmental Protection Agency (EPA) 2007 Heavy-Duty Highway Rule on the decrease of BC and PM_2.5 concentrations during the study period.

Implications: This study suggests that there was an observable impact of the U.S EPA 2007 Heavy-Duty Highway Rule on the ambient black carbon concentrations in Rochester, New York. Aethalometer Delta-C was used as an input variable in source apportionment models and it allowed the separation of traffic (especially diesel) emissions from wood combustion emissions.     

Apportionment of Ambient Primary and Secondary Pollutants during a 2001 Summer Study in Pittsburgh Using U.S. Environmental Protection Agency UNMIX

Abstract

Apportionment of primary and secondary pollutants during the summer 2001 Pittsburgh Air Quality Study (PAQS) is reported. Several sites were included in PAQS, with the main site (the supersite) adjacent to the Carnegie Mellon University campus in Schenley Park. One of the additional sampling sites was located at the National Energy Technology Laboratory, located ～18 km southeast of downtown Pittsburgh. Fine particulate matter (PM_2.5) mass, gas-phase volatile organic material (VOM), particulate semivolatile and nonvolatile organic material (NVOM), and ammonium sulfate were apportioned at the two sites into their primary and secondary contributions using the U.S. Environmental Protection Agency UNMIX 2.3 multivariate receptor modeling and analysis software. A portion of each of these species was identified as originating from gasoline and diesel primary mobile sources. Some of the organic material was formed from local secondary transformation processes, whereas the great majority of the secondary sulfate was associated with regional transformation contributions. The results indicated that the diurnal patterns of secondary gas-phase VOM and particulate semivolatile and NVOM were not correlated with secondary ammonium sulfate contributions but were associated with separate formation pathways. These findings are consistent with the bulk of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport and, thus, decoupled from local activity involving organic pollutants in the metropolitan area.     

Beryllium-7 Measurements in the Houston and Phoenix Urban Areas: An Estimation of Upper Atmospheric Ozone Contributions

Abstract

Natural radionuclides have been proposed as a means of assessing the transport of ozone (O₃) and aerosols in the troposphere. Beryllium-7 (⁷Be) is produced in the upper troposphere and lower stratosphere by the interaction of cosmogenic particles with atmospheric nitrogen and oxygen. ⁷Be has a 53.29-day half-life (478 keV γ) and is known to attach to fine particles in the atmosphere once it is formed. It has been suggested that O₃ from aloft can be transported into rural and urban regions during stratospheric–tropospheric folding events leading to increased background levels of O₃ at the surface. ⁷Be can be used as a tracer of upper atmospheric air parcels and the O₃ associated with them. Aerosol samples with a 2.5-µm cutoff were collected during 12-hr cycles (day/night) for a 30-day period at Deer Park, TX, near Houston, in August– September of 2000, and at Waddell, AZ, near Phoenix, in June–July of 2001. A comparison of ⁷Be levels with 12-hr O₃ averages and maxima shows little correlation. Comparison of nighttime and daytime O₃ levels indicate that during the day, when mixing is anticipated to be higher, the correlation of ⁷Be with O₃ in Houston is approximately twice that observed at night. This is consistent with mixing and with the anticipated loss of O₃ by reaction with nitric oxide (NO) and dry deposition. At best, 30% of the O₃ variance can be explained by the correlation with ⁷Be for Houston, less than that for Phoenix where no significant correlation was seen. This result is consistent with the intercept values obtained for ⁷Be correlations with either O₃ 24-hr averages or O₃ 12-hr maxima and is also in the range of the low O₃ levels (25 ppb) observed at Deer Park during a tropical storm event where the O₃ is attributable primarily to background air masses. That is, maximum background O₃ level contributions from stratospheric sources aloft are estimated to be in the range of 15–30 ppb in the Houston, TX, and Phoenix, AZ, area, and levels above these are because of local tropospheric photochemical production.     

Evaluation of effectiveness of EDTA and sodium thiosulfate in removing metal toxicity toward sea urchin embryo-larval applying the TIE

Since the development of the TIE (Toxicity Identification and Evaluation) in 1988 it has been assumed that the capacity of EDTA and sodium thiosulfate to complex some metals, and thus remove their toxicity, can be applied to both freshwater and seawater ecotoxicological tests and the results subsequently interpreted. However, it is now known that there is a wide variability in the extent of this complexation. In this context, the removal of toxicity caused by the presence of Hg²⁺, Cd²⁺, Cu²⁺, Cr⁶⁺, Zn²⁺, Ni²⁺, Pb²⁺, Ag¹⁺ and Se²⁺, through metal complexation by EDTA and sodium thiosulfate, in relation to the performance of embryo-larval tests with the sea urchin Arbacia lixula was investigated. It was observed that EDTA was capable of removing the toxicity of Pb²⁺, Zn²⁺ and Cu²⁺ while sodium thiosulfate only reduced the toxicity of Ag¹⁺. Compared to the complexation observed in freshwater ecotoxicological tests, the complexing agents used in this study (EDTA and sodium thiosulfate) have a lower capacity to complex metals in the marine ecotoxicological test with A. lixula.