Leachate injection using vertical wells in bioreactor landfills

Leachate recirculation or liquid injection in municipal solid waste landfills offers economic and environmental benefits. The key objective of this study was to carry out numerical evaluation of key design variables for leachate recirculation system consisting of vertical wells. In order to achieve the objective, numerical modeling was carried out using the finite-element model HYDRUS-2D. The following design parameters were evaluated by simulating liquid pressure head on the liner and the wetted width of the waste under steady-state flow conditions: (1) hydraulic conductivities of the waste and vertical well backfill; (2) liquid injection rate and dosing frequency; (3) well diameter, screen height and screen depth; and (4) hydraulic conductivity of the leachate collection system, slope of the leachate collection system and spacing of the leachate collection pipes. The key findings of this study are as follows. The well diameter, hydraulic conductivity of the well drainage pack, and screen height and screen depth of the well have very little effect on the wetted width for a given liquid flux. The wetted width and the injection pressure for a given liquid flux decrease with the increase in the hydraulic conductivity of the waste. The pressure head on the liner increases with the decrease in the vertical distance between the bottom of the well screen and the top of leachate collection system. The liquid injection flux increases with the decrease in hydraulic conductivity of the leachate collection system. Unlike sand (k approximately 10(-4)m/s), pea gravel (k approximately 0.01 m/s) resulted in less than 0.3m pressure head on the liner for all simulations carried out in this study.     

Leaching of inorganic contaminants from cement-based waste materials as a result of carbonation during intermittent wetting

Characterization of the leaching behavior of wastes is a crucial step in the environmental assessment for reuse or disposal scenarios. The release of inorganic contaminants from waste materials is typically evaluated by tank leaching of continuously water-saturated material. However, materials, in many field or management scenarios, experience cyclic wetting and drying under varied environmental conditions (i.e. variable relative humidity, atmospheric CO2 or CO2 from biologic activities). During periods of storage in an unsaturated environment, many processes may occur that can influence the release potential and release rate of inorganic constituents. The research presented here was carried out to examine how the phenomena of carbonation during drying influence the release of inorganic contaminants from Portland cement-based materials during cyclic wetting and storage. Batch equilibrium leaching tests were used to determine constituent solubility as a function of pH. Dynamic leaching tests on monolithic material were carried out to determine the rate of constituent release as a function of leaching time and intermittent storage conditions. This paper presents the results observed for three typical waste constituents, arsenic, cadmium and lead.     

Application of tracer ratio and inverse dispersion methods with boat-based plume measurements to estimate ammonia emissions from seabird colonies

Ammonia emissions from two contrasting seabird colonies in Scotland were measured, based on the determination of atmospheric concentrations downwind of the colonies. Atmospheric concentrations of ammonia (NH₃) across the downwind plume were compared with the inverse application of a Gaussian dispersion model (ID) to calculate the modelled NH₃ emission that would generate the measured cross-wind-integrated plume concentration. In parallel, a tracer gas (sulphur hexafluoride, SF₆) was released from the colonies with air samples taken to allow determination of SF₆ concentrations. On the basis of the known emission rate of SF₆, the magnitude of ammonia emissions was estimated by the cross-wind-integrated tracer ratio (TR) of NH₃/SF₆ concentrations. Coupled with data on annual bird attendance, the measurements indicate annual emissions from the Isle of May and the Bass Rock of 18 and 132 tonnes NH₃-N year^–1, respectively. The measured NH₃ emissions were compared with estimates of seabird nitrogen excretion to estimate the proportion of excreted N that is volatilised as NH₃ (F_Nr). The emission estimates of the two methods compared favourably, giving 4 and 6 kg NH₃-N h^–1 (F_Nr = 15%) for the Isle of May for the ID and TR methods, respectively, and 21 and 25 kg NH₃-N h^–1 (F_Nr = 50%) for the Bass Rock for the ID and TR methods, respectively. The results provide the first measurement-based estimates to allow regional up scaling of ammonia emissions from seabirds.     

Long-term behavior of passively aerated compost methanotrophic biofilter columns

The methane oxidation potential of several types of compost methanotrophic biofilter columns were compared in the laboratory over a period of 220 days. The results indicate an increase in methanotrophic activity over a period of about 100 days, up to a maximum of 400 g m(-2) day(-1), and a gradual decline to about 100 g m(-2) day(-1) within the next 120 days. High methane oxidation rates appear to be restricted to a small area of the column, 10-15 cm thick. Based on the laboratory investigations carried out to determine the cause for the decline in methane oxidation rate, it was concluded that the formation of exopolymeric substances (EPS), at the zones of maximum methane oxidation, was responsible for this decline. In monitoring methane oxidation in a column for up to 600 days, it was observed that mixing of the medium after formation of EPS enabled the column to temporarily recover high performance. The results suggest that stable, homogenous compost, with a low C/N and low ammonium content, mixed on a regular basis, could achieve and maintain high methane oxidation efficiencies.     

Nitrous Oxide in Agricultural Drainage Waters Following Field Fertilisation

Dissolved nitrous oxide (N₂O), nitrate (NO₃ ^-), and ammonium (NH₄ ⁺) concentrations in an agricultural field drain were intensively measured over the period of field nitrogen (N) fertilisation and for several weeks thereafter. Supersaturations of dissolved N₂O were observed in field drain waters throughout the study. On entry to an open drainage ditch, concentrations of dissolved N₂O rapidly decreased and a total N₂O-N emission via this pathway of 13.2 g over the period of study (45 days) was calculated. This compared with a predicted emission of the order of 300 g, based on measured losses of NO₃ ^- and NH₄ ⁺ in the field drainage water, and the default IPCC emission factor of 0.01 kg N₂O-N per kg Nentering rivers and estuaries. In contrast to widespread evidence of a clear relationship between the amount of N applied to agricultural land and subsequent direct N₂O emission from the soil surface, the relationship between the amount of N₂O in soil drainage waters and the amount of N applied was poor. We conclude that the complexity, both spatially and temporally, of the processes ultimately responsible for the amount of N₂O in agricultural drainage waters make a straightforward relationship between N₂O concentration and N application rate unlikely in all but the simplest of systems.     

Methane generation in tropical landfills: simplified methods and field results

This paper deals with the use of simplified methods to predict methane generation in tropical landfills. Methane recovery data obtained on site as part of a research program being carried out at the Metropolitan Landfill, Salvador, Brazil, is analyzed and used to obtain field methane generation over time. Laboratory data from MSW samples of different ages are presented and discussed; and simplified procedures to estimate the methane generation potential, Lo, and the constant related to the biodegradation rate, k are applied. The first order decay method is used to fit field and laboratory results. It is demonstrated that despite the assumptions and the simplicity of the adopted laboratory procedures, the values Lo and k obtained are very close to those measured in the field, thus making this kind of analysis very attractive for first approach purposes.     

Characterization and Properties of Hydrophilic Cellulose Acetate Propionate Derivative

The chemical modification of Acrylamidomethyl Cellulose Acetate Propionate (AMCAP) was carried out by radical addition of acrylic acid. The structural modification was confirmed with the aid of FTIR, MS and NMR techniques. Thermal properties of hydrophilic cellulose derivative (AMCAP–H₂O₂) such as glass transition (T_g 153 °C) and thermal stability (372.7 °C) were determined by DSC and TGA techniques, respectively. These thermal properties confirmed the introduction of carboxylic groups into AMCAP structure, which causes an impact in their properties. The AMCAP–H₂O₂ shows minor contact angle compared to AMCAP, giving a more hydrophilic characteristic, due to acrylic acid addition into the side chains of AMCAP polymer.