深圳大气PM2.5中水溶性有机物的来源特征

对2017年9月~2018年8月深圳市北部大气PM_2.5中水溶性有机物（WSOM）的质量浓度、质谱及来源结构进行测量和分析.结果表明：PM_2.5的质量浓度为（32.3±18.4）μg/m³,WSOM的质量浓度为（9.4±5.7）μg/m³,占颗粒物总有机物的（77.6%±14.0%）.质谱分析显示,WSOM的氧碳比（O/C）平均值达到（0.57±0.09）,属于二次有机物的O/C值范围,且生物质燃烧排放的离子碎片C₂H₄O₂⁺的丰度显著,说明WSOM的来源中有显著的生物质燃烧排放的有机气溶胶.为了明确WSOM的来源结构,利用正矩阵因子分解法（PMF）模型进行来源解析,发现3个合理因子：高氧化态有机气溶胶（MO-OOA）,低氧化态有机气溶胶（LO-OOA）和生物质燃烧（BBOA）,贡献比例分别为51.7%,31.8%和16.5%.MO-OOA和BBOA贡献浓度均呈现秋冬高、春夏低的季节变化特征,反向轨迹分析显示其与内陆污染传输关系密切.LO-OOA的变化相对稳定,本地源的贡献较大.结合¹⁴C同位素示踪法对秋冬季WSOM样品分析,发现机动车等化石源二次有机物是WSOM的主要来源,贡献比例达到53.9%,需继续加强对化石燃料控制来降低WSOM污染.     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

机动车轮胎磨损颗粒物化学组分特征研究

为研究机动车道路行驶过程中轮胎磨损排放的颗粒物理化特性,利用轮胎轮廓仿真磨耗仪,对国内主流17种轮胎胎面进行仿真磨耗实验,获得颗粒物样品,提取并检测其中18种元素和20种多环芳烃（PAHs）的含量.结果显示,元素和PAHs含量因轮胎品牌和速度等级的不同而差异显著.18种元素平均含量为（99.04±68.43）mg/g,占样品总重的9.90%,其中Si（88.97±67.85）mg/g、Zn（6.77±1.64）mg/g和Na（1.05±0.75）mg/g的平均含量均超过1mg/g,Cd的含量最低,为（0.43±0.31）μg/g.20种PAHs含量之和（∑20PAHs）在12.13~433.64 μg/g,平均为（94.13±110.18）μg/g,PY的平均含量最高（30.98±31.27）μg/g,其次是CHR、BaP、FA、PHE和BghiP,平均含量最低的是AC（0.58±0.2）μg/g;从环数看,以4环PAHs为主（占∑20PAHs的45.03%~67.93%）,其次为3环（平均含量为15.45%）和5环（平均含量为12.62%）.总体来说,国外品牌轮胎样品中元素和PAHs含量略高于国内品牌,而主要PAHs环数略低于国内品牌.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

悬浮填料投加对AnMBR性能及膜污染的影响

研究了悬浮填料投加对分置式厌氧膜生物反应器（AnMBR）的COD去除效果、污泥混合液特性及膜污染的影响。试验结果表明:在反应器有机负荷为2.09 kg/（m3·d）,污泥负荷为0.54 kg/（kg·d）,水力停留时间（HRT）为48 h,温度为（35±2）℃的条件下,与未投加悬浮填料阶段比较,投加填料后AnMBR的COD总去除率由96.6%提高至97.9%,甲烷产率提高16.0%。同时投加悬浮填料后AnMBR混合液污泥平均粒径增大,滤饼层阻力、总阻力、滤饼层阻力在总阻力中的占比较未投加悬浮填料时分别降低7.8、6.5和1.3百分点,溶解性胞外聚合物（SEPS）和结合性胞外聚合物（BEPS）浓度分别降低了20.5%和29.4%,跨膜压差（TMP）线性增长速率降低,膜污染速率明显减缓。因此,投加悬浮填料可在不增加能耗的情况下改善污泥混合液特性,起到强化AnMBR处理效果和控制膜污染的作用。     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

中国工业园区绿色发展政策对比分析及对策研究

为了提升我国工业园区绿色发展水平,对目前我国工业园区发展历程、现状特征进行了分析,对工业园区绿色发展政策进行了梳理和对比,并结合工业园区绿色发展中存在的问题提出了对策建议.研究表明:①我国工业园区经历了快速发展、调整发展和科学发展等阶段,在经济发展、资源与能源优化利用、污染减排等方面成效显著.②我国工业园区绿色发展的相关政策主要体现在国家生态工业示范园区创建、园区循环化改造、国家低碳工业园区试点、绿色园区建设和UNIDO绿色工业园区创建等工作中,这些政策在推动主体、实施路径、侧重方向上各不相同又各有特色,对推动工业园区节能减排绩效明显.③目前,我国工业园区绿色发展存在的问题主要表现在重视程度有待提升、风险防范意识有待加强、创新能力有待提高等方面.为此,提出了我国工业园区绿色发展对策建议:积极践行绿色发展理念,推进园区绿色化、生态化、低碳化建设,实现经济环境双赢;注意环境风险防控,确保环境安全;创新管理机制,强化监督管理.      

Plasmonic silver/silver oxide nanoparticles anchored bismuth vanadate as a novel visible-light ternary photocatalyst for degrading pharmaceutical micropollutants

The degradation of pharmaceutical micropollutants is an intensifying environmental problem and synthesis of efficient photocatalysts for this purpose is one of the foremost challenges worldwide. Therefore, this study was conducted to develop novel plasmonic Ag/Ag₂O/BiVO₄ nanocomposite photocatalysts by simple precipitation and thermal decomposition methods, which could exhibit higher photocatalytic activity for mineralized pharmaceutical micropollutants. Among the different treatments, the best performance was observed for the Ag/Ag₂O/BiVO₄ nanocomposites (5 wt.%; 10 min's visible light irradiation) which exhibited 6.57 times higher photodegradation rate than the pure BiVO₄. Further, the effects of different influencing factors on the photodegradation system of tetracycline hydrochloride (TC-HCl) were investigated and the feasibility for its practical application was explored through the specific light sources, water source and cycle experiments. The mechanistic study demonstrated that the photogenerated holes (h⁺), superoxide radicals (?O₂^?) and hydroxyl radicals (?OH) participated in TC-HCl removal process, which is different from the pure BiVO₄ reaction system. Hence, the present work can provide a new approach for the formation of novel plasmonic photocatalysts with high photoactivity and can act as effective practical application for environmental remediation.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

新冠肺炎疫情期间我国居民佩戴口罩防护行为研究

口罩作为阻隔病毒传染的物理方式之一,其能阻断病原体经飞沫传播,同时具有双向隔离保护作用.佩戴口罩对于公众防范新型冠状病毒（2019-nCoV）感染的风险和维持人体基本健康具有重要意义.为了解新型冠状病毒肺炎（COVID-19,简称“新冠肺炎”）疫情期间我国居民佩戴口罩的行为模式特征,基于新冠肺炎疫情期间我国人群环境暴露行为模式调查,分析全国31个省（自治区、直辖市）居民在新冠肺炎疫情期间佩戴口罩的行为特征,并探讨不同潜在风险人群佩戴口罩行为模式的差异性.结果表明:①在新冠肺炎疫情期间,我国人群外出佩戴口罩的比例在99%以上,显著高于非疫情期间的口罩佩戴率（16.05%）,其中,医务人员以及与人群广泛接触群体的口罩佩戴率最高（100%）.②居民以仅佩戴医用外科口罩、仅佩戴一次性使用医用口罩以及佩戴医用外科口罩和一次性使用医用口罩3种模式为主,占31种口罩佩戴模式的60%以上.③新冠肺炎疫情期间,不同职业人群、不同所属人群以及不同疫情地区人群佩戴口罩的比例均存在显著差异.④新冠肺炎疫情期间,我国居民佩戴口罩的更换频次多为累计使用时长4 h更换一次和累计使用时长24 h更换一次.⑤人群外出佩戴口罩的比例随新冠肺炎疫情严重程度的升高而增加.尽管新冠肺炎疫情分布特征和管控措施存在差异,但居民佩戴口罩行为均表现良好,其中居住地不存在疑似病例的人群比居住地存在疑似病例的人群的口罩佩戴率更高,说明人群佩戴口罩行为与疫情的发展可能存在一定的相互作用.研究显示,新冠肺炎疫情期间我国人群佩戴口罩这一防护行为总体执行较好.