Life cycle assessment of biodiesel fuel production from waste cooking oil in Okayama City

A life cycle assessment (LCA) is performed to make clear of the actual environment impacts from conversation of waste cooking oil (WCO) to biodiesel fuel (BDF) in Okayama. A scenario analysis is carried out based on different participation rate of residents who separate WCO from general waste, corresponding to different BDF utilisation rate in transportation system. Sub scenarios complying with different gas emission standards regarding vehicles are designed as well. Afterwards, life cycle impact assessment is conducted to focus on global warming, acidification, and urban air pollution. Overall improvement of almost all kinds of life cycle inventories is significant when diesel is replaced with BDF, demonstrating that a shift from WCO-to-incineration to WCO-to-BDF is more beneficial. Under carbon neutral, compared to base scenario (S0), about 746.05 ton CO₂ emission will be reduced annually in the scenario with 100 % BDF utilisation in vehicles (S4). Meanwhile, total external cost in three environmental impacts (EI) sharply reduces by 51.90 %, showing much economic sustainability in S4. Moreover, the manufacturing cost for producing one litter WCO-to-BDF is 97.32 Yen. Sensitivity analysis shows that the gas emission standard regarding vehicles had much bigger effect on EI than BDF manufacturing process in this research.     

Spatial simulation and LCA evaluation on the plastic waste recycling system in Tianjin

With the rapid economic development in China, the amount of plastic waste (PW) generated has greatly increased and much of the waste is currently not treated. To reduce greenhouse gas (GHG) emissions from recycling of PW, we estimated the PW flow and considered methods to improve the household PW recycling system in Tianjin by adjusting processes during transportation and establishing a PW recycling factory in Zi’ya Industrial Park. The goal of the study was to identify reasonable improvements for the recycling system and clarify the environmental load. Geographic information system (GIS) technology was used to simulate transport processes for comparing GHG emissions from the transport processes between the present case and an improved case. Life cycle assessment (LCA) was used to compare GHG emissions between a projected scenario and a baseline scenario. Estimated GHG emissions during transport processes in the improved case were reduced by about 12,197 t CO₂ eq per year compared to the present case, equivalent to about 65.9 % of the total emissions in the present case. GHG emissions in the projected scenario were about 101,738 t CO₂ eq less per year than the baseline scenario, equivalent to about 75.5 % of the total emissions in the baseline scenario.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

Reduction of hazardous elements contained in sewage sludge incineration ash

Research and experimental studies were carried out in relation to reduction of hazardous elements contained in sewage sludge incineration ash. A questionnaire survey was conducted in 69 Japanese municipalities with sewage sludge incineration facilities. Selenium content in bag filter ash and ceramic filter ash was relatively higher than that in ash of cyclone and electrostatic precipitators. It was assumed that selenium vaporized in the furnace was due to adsorb in the fly ash on filter when passing through the low-temperature filter. To reduce high boiling point heavy metals in the ash, sewage sludge and incineration ash were heated up using a small muffle furnace. As the result, the chrome and nickel contents were reduced. A decrease in the surface area of ash and the reduction of elements occurred at the same time in sewage sludge and incineration ashes tested in this study.     

The effects of using reprocessable material on the durability and mechanical properties of landfill leachate collection HDPE pipes

This paper investigated the durability and mechanical properties of landfill leachate collection HDPE pipes which had been made of different weight percent amounts of virgin and reprocessable HDPE compounds (VC and RC). Durability is reported base on the chemical properties, obtained through oxidative induction time (OIT) and melt flow index (MFI) measurements, at the temperature of 50 °C and over a period of 12 months immersion in a synthetic leachate. Mechanical properties are also described according to tensile and pressure tests which had been conducted on the pipes samples. All of the factors were examined had been affected by the addition of RC, but for the special combination the antioxidant depletion was significantly affected by the experimental aging condition and no important changes had been observed in the other pipe properties. The results from OIT tests indicate that the rate of antioxidant depletion is reduced by an increase in the weight percent amounts of RC, during the experimental aging condition. This reduction is probably attributed to the extraction of antioxidants from RC in their recovery process. Finally, although these results are related to the particular HDPE compound, antioxidant formulation and condition examined, but it can be said that the use of clean own reprocessable material for the production of landfill leachate pipes shall be permitted without limitations.     

Food Industry Co-streams: Potential Raw Materials for Biodegradable Mulch Film Applications

Vast amounts of co-streams are generated from plant and animal-based food processing industries. Efficient utilization of these co-streams is important from an economic and environmental perspective. Non-utilization or under-utilization of co-streams results in loss of potential revenues, increased disposal cost of these products and environmental pollution. At present, extensive research is taking place around the globe towards recycling of co-streams to generate value-added products. This review evaluates various co-streams from food processing industries as raw materials in developing biodegradable agricultural mulching applications. Among the agriculture-based co-streams, potato peels, tomato peels, carrot residues, apple pomace, coffee residues and peanut residues were reviewed with respect to production amount, composition, film forming components and film forming capabilities. Similarly, selected co-streams from slaughterhouses, poultry and fish processing industries were also reviewed and evaluated for the same purpose.     

Preparation and Properties of a Chitosan–Hyaluronic Acid-Polypyrrole Conductive Hydrogel Catalyzed by Laccase

Electro conductive hydrogels, consisting of chitosan (CS), hyaluronic acid (HA), and polypyrrole (PPy), were prepared via an in situ enzymic polymerization of pyrrole in the CS–HA hydrogel, using laccase as the catalyst. This CS–HA–PPy composite hydrogel showed good conductivity. The chemical structure and morphology of this conductive hydrogel were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction technique. For CS–HA–PPy and CH–HA hydrogel, the temperature at which fastest decomposition occurred was 260 and 244 °C, respectively. That means the thermal stability of CS–HA–PPy is better than CS–HA hydrogel. The conductive hydrogel also showed excellent swelling and deswelling behaviors.     

Environmentally Friendly Oil-Modified Polyesters as Polymeric Plasticizers for Poly(vinyl chloride)

Oil-modified polyesters were synthesized to serve as polymeric plasticizers for PVC. A total of four polymeric plasticizers with different average molecular weights were prepared. Characterizations were done using Fourier-transformed infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and gel permeation chromatography. Some of the tests conducted on PVC films include thermal stability test using thermogravimetric analyser, determination of glass transition temperature (T_g), plasticizer migration and leaching resistance test, morphology study of plasticized PVC films using field emission scanning microscope, toxicity test, and tensile test. Owing to the plasticizing effect of the palm oil-based compound, T_g of the plasticized PVC has decreased to an average of 65 °C at 20 wt% loading. The polymeric plasticizer is also able to contribute positively to the thermal stability and mechanical properties of the PVC films. Some of the advantages of incorporating polymeric plasticizer with high molecular weight includes lower rate of leaching from plastic, and improved tensile strength and elongation at break. Besides, thermal stability of the plastic studied using Kissinger’s and Flynn–Wall–Ozawa’s approaches shows that PVC blended with high molecular weight oil-modified polyester is more thermally stable, evidenced by the increase in the activation energy of decomposition, E_d. Toxicity test using brine shrimp egg shows encouraging results, where the oil-based plasticizer is considerably less toxic compared to some of the commercial plasticizers.     

Optimization of Pellet Production from Agro-Industrial By-Products: Effect of Plasticizers on Properties of Pellets and Composite Pots

The present study aimed to optimize the pellets formulation (deoiled rice bran, potato peel powder and plasticizers) for the development of the injection molded pots. The maximum hardness and bulk density (desirable responses) were obtained for pellets having 100 g of deoiled rice bran, 100 g potato peel powder and 14 % of cashew nut shell liquid (CNSL) as well as 14 % of glycerol (GL) (on raw material basis). The optimized pellets and the pots developed from them were characterized for their physico-chemical, functional, rheological and morphological properties. Expansion ratio, pellet durability index and hardness of the pellets with 14 % CNSL were found to be 1.097, 98.647 % and 485.551 N, respectively. For pellets with 14 % GL expansion ratio, pellet durability index and hardness were found to be 1.150, 97.747 % and 462.949 N, respectively. The biodegradation analysis of the pots developed from optimized pellets with 14 % CNSL and GL degraded in 11 and 9 weeks, respectively. Porosity, puncture force, density and hardness of ‘AP’ pots were 27.473 %, 495.731 N, 1.549 g/ml and 542.641 N, respectively. However, for ‘BP’ pots, the porosity, puncture force, density and hardness were 32.548 %, 440.149 N, 1.191 g/ml and 507.841 N, respectively. Pots prepared from 14 % CNSL (AP) were better in physical and mechanical properties as compared to pots developed from glycerol.