Further studies on the uptake of persistent organic pollutants (POPs) by polyurethane foam disk passive air samplers

Passive air samplers (PAS) can be used to monitor semi-volatile organic compounds in the atmosphere. Polyurethane foam (PUF) disks are a popular sampling medium because they have a high retention capacity for such compounds. This paper reports a highly time-resolved uptake study, to derive uptake rate data under field conditions, and investigate the effects of using different foam densities on the uptake rate. PUF disks were deployed alongside an active sampler, for periods of up to 12 weeks. The uptake rates were measured for a range of gas- and particle-bound persistent organic pollutants (polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs)), of different properties, to explore whether gas–particle partitioning affected uptake rate. Uptake rates for two different densities of foam (0.021 and 0.035 g cm^?3) were not statistically significantly different from each other. Uptake rates of light PCBs averaged ～6.5 m³ day^?1, somewhat higher than in previous studies; higher wind speeds and lower temperatures in this study are the likely reason for this difference. The study showed: i) the uptake rate of the compound with lowest K_OA considered in this study (PCB-28/31) declined in the later weeks, indicating an approach to equilibrium; ii) uptake rates of lighter BDEs and heavier PCBs (compounds of intermediate K_OA in this study) remain similar throughout the study period, indicating that they are not approaching equilibrium during the 12-week-study; iii) uptake rates were typically: ～8 m³ day^?1 for PCB-52; ～9.5 m³ day^?1 for PCB-95; ～11 m³ day^?1 for BDE-28 and ～2 m³ day^?1 BDE-99. The latter compound has an important particle-bound component and this lowers the sampling rate compared to predicted uptake rates for compounds which are in the gas phase only. It is shown that knowledge of gas–particle partitioning is needed to correct for this effect, and to improve predicted uptake rates.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta—Seasonal variations at urban,suburban, and rural ambient air monitoring sites

Twenty-eight polycyclic aromatic hydrocarbons (PAH) and methylated PAHs (Me-PAH) were measured in daily PM_2.5 samples collected at an urban site, a suburban site, and a rural site in and near Atlanta during 2004 (5 samples/month/site). The suburban site, located near a major highway, had higher PM_2.5-bound PAH concentrations than did the urban site, and the rural site had the lowest PAH levels. Monthly variations are described for concentrations of total PAHs (∑PAHs) and individual PAHs. PAH concentrations were much higher in cold months than in warm months, with average monthly ∑PAH concentrations at the urban and suburban-highway monitoring sites ranging from 2.12 to 6.85 ng m^?3 during January–February and November–December 2004, compared to 0.38–0.98 ng m^?3 during May–September 2004. ∑PAH concentrations were found to be well correlated with PM_2.5 and organic carbon (OC) within seasons, and the fractions of PAHs in PM_2.5 and OC were higher in winter than in summer. Methyl phenanthrenes were present at higher levels than their un-substituted homologue (phenanthrene), suggesting a petrogenic (unburned petroleum products) input. Retene, a proposed tracer for biomass burning, peaked in March, the month with the highest acreage and frequency of prescribed burning and unplanned fires, and in December, during the high residential wood-burning season, indicating that retene might be a good marker for burning of all biomass materials. In contrast, potassium peaked only in December, indicating that it might be a more specific tracer for wood-burning.     

Evaluating inter-continental transport of fine aerosols:(2) Global health impact

In this second of two companion papers, we quantify for the first time the global impact on premature mortality of the inter-continental transport of fine aerosols (including sulfate, black carbon, organic carbon, and mineral dust) using the global modeling results of (Liu et al., 2009). Our objective is to estimate the number of premature mortalities in each of ten selected continental regions resulting from fine aerosols transported from foreign regions in approximately year 2000. Our simulated annual mean population-weighted (P-W) concentrations of total PM2.5 (aerosols with diameter less than 2.5 μm) are highest in East Asia (EA, 30 μg m^?3) and lowest in Australia (3.6 μg m^?3). Dust is the dominant component of PM2.5 transported between continents. We estimate global annual premature mortalities (for adults age 30 and up) due to inter-continental transport of PM2.5 to be nearly 380 thousand (K) in 2000. Approximately half of these deaths occur in the Indian subcontinent (IN), mostly due to aerosols transported from Africa and the Middle East (ME). Approximately 90K deaths globally are associated with exposure to foreign (i.e., originating outside a receptor region) non-dust PM2.5. More than half of the premature mortalities associated with foreign non-dust aerosols are due to aerosols originating from Europe (20K), ME (18K) and EA (15K); and nearly 60% of the 90K deaths occur in EA (21K), IN (19K) and Southeast Asia (16K). The lower and higher bounds of our estimated 95% confidence interval (considering uncertainties from the concentration–response relationship and simulated aerosol concentrations) are 18% and 240% of the estimated deaths, respectively, and could be larger if additional uncertainties were quantified. We find that in 2000 nearly 6.6K premature deaths in North America (NA) were associated with foreign PM2.5 exposure (5.5K from dust PM2.5). NA is least impacted by foreign PM2.5 compared to receptors on the Eurasian continent. However, the number of premature mortalities associated with foreign aerosols in NA (mostly occurring in the U.S.) is comparable to the reduction in premature mortalities expected to result from tightening the U.S. 8-h O₃ standard from 0.08 ppmv to 0.075 ppmv. International efforts to reduce inter-continental transport of fine aerosol pollution would substantially benefit public health on the Eurasian continent and would also benefit public health in the United States.     

Optimal temporal scale for the correlation of AOD and ground measurements of PM2.5 in a real-time air quality estimation system

Aerosol optical depth (AOD), an indirect estimate of particulate matter using satellite observations, has shown great promise in improving estimates of PM_2.5 (particulate matter with aerodynamic diameter less than or equal to 2.5 μm) surface. Currently, few studies have been conducted to explore the optimal way to apply AOD data to improve the model accuracy of PM_2.5 in a real-time air quality system. We believe that two major aspects may be worthy of consideration in that area: 1) an approach that integrates satellite measurements with ground measurements in the estimates of pollutants and 2) identification of an optimal temporal scale to calculate the correlation of AOD and ground measurements. This paper is focused on the second aspect, identifying the optimal temporal scale to correlate AOD with PM_2.5. Five following different temporal scales were chosen to evaluate their impact on the model performance: 1) within the last 3 days, 2) within the last 10 days, 3) within the last 30 days, 4) within the last 90 days, and 5) the time period with the highest correlation in a year. The model performance is evaluated for its accuracy, bias, and errors based on the following selected statistics: the Mean Bias, the Normalized Mean Bias, the Root Mean Square Error, Normalized Mean Error, and the Index of Agreement. This research shows that the model with the temporal scale: within the last 30 days, displays the best model performance in a southern multi-state area centered in Mississippi using 2004 and 2005 data sets.     

The stable carbon isotope composition of PM2.5 and PM10 in Mexico City Metropolitan Area air

The sources and distribution of carbon in ambient suspended particles (PM_2.5 and PM₁₀) of Mexico City Metropolitan Area (MCMA) air were traced using stable carbon isotopes (¹³C/¹²C). Tested potential sources included rural and agricultural soils, gasoline and diesel, liquefied-petroleum gas, volcanic ash, and street dust. The complete combustion of LP gas, diesel and gasoline yielded the lightest δ¹³C values (?27 to ?29‰ vs. PDB), while street dust (PM₁₀) represented the isotopically heaviest endmember (?17‰). The δ¹³C values of rural soils from four geographically separated sites were similar (?20.7 ± 1.5‰). δ¹³C values of particles and soot from diesel and gasoline vehicle emissions and agricultural soils varied between ?23 and ?26‰. Ambient PM samples collected in November of 2000, and March and December of 2001 at three representative receptor sites of industrial, commercial and residential activities had a δ¹³C value centered around ?25.1‰ in both fractions, resulting from common carbon sources. The predominant carbon sources to MCMA atmospheric particles were hydrocarbon combustion (diesel and/or gasoline) and particles of geological origin. The significantly depleted δ¹³C values from the industrial site reflect the input of diesel combustion by mobile and point source emissions. Based on stable carbon isotope mass balance, the carbon contribution of geological sources at the commercial and residential sites was approximately 73% for the PM₁₀ fraction and 54% for PM_2.5. Although not measured in this study, biomass-burning emissions from nearby forests are an important carbon source characterized by isotopically lighter values (?29‰), and can become a significant contributor (67%) of particulate carbon to MCMA air under the prevalence of southwesterly winds. Alternative sources of these ¹³C-depleted particles, such as cooking fires and municipal waste incineration, need to be assessed. Results show that stable carbon isotope measurements are useful for distinguishing between some carbon sources in suspended particles to MCMA air, and that wind direction has an impact on the distribution of carbon sources in this basin.     

混凝-生物接触氧化处理合成橡胶碱洗废水

对化学合成橡胶碱洗废水进行了有机组分和可生化性分析,废水主要含有氯甲烷、六甲苯、异丁醇、甲醇等污染物质,生化降解实验中废水TOC可在6 d内从60.9 mg/L下降至0.0 mg/L,可生化降解性好,适于生化处理。选择混凝-生物接触氧化组合工艺对废水进行处理,采用优化条件(pH=8、PAC=40 mg/L、PAM=8 mg/L)进行混凝,碱洗废水COD去除率为9.95%~72.94%(平均31.51%);混凝后的碱洗废水与冲洗废水1∶5混合进行接触氧化处理,在HRT为36 h的情况下,COD去除率为65.6%~72.6%(平均70.4%),出水COD为134~331 mg/L,满足企业废水排放市政管网的要求;同时,实验发现COD去除率与COD容积负荷存在指数函数变化关系。     

Nitrogen limited biobarriers remove atrazine from contaminated water: laboratory studies

Atrazine is one of the most frequently used herbicides. This usage coupled with its mobility and recalcitrant nature in deeper soils and aquifers makes it a frequently encountered groundwater contaminant. We formed biobarriers in sand filled columns by coating the sand with soybean oil; after which, we inoculated the barriers with a consortium of atrazine-degrading microorganisms and evaluated the ability of the barriers to remove atrazine from a simulated groundwater containing 1 mg L(-1) atrazine. The soybean oil provided a carbon rich and nitrogen poor substrate to the microbial consortium. Under these nitrogen-limiting conditions it was hypothesized that bacteria capable of using atrazine as a source of nitrogen would remove atrazine from the flowing water. Our hypothesis proved correct and the biobarriers were effective at removing atrazine when the nitrogen content of the influent water was low. Levels of atrazine in the biobarrier effluents declined with time and by the 24th week of the study no detectable atrazine was present (limit of detection<0.005 mg L(-1)). Larger amounts of atrazine were also removed by the biobarriers; when biobarriers were fed 16.3 mg L(-1) atrazine 97% was degraded. When nitrate (5 mg L(-1) N), an alternate source of nitrogen, was added to the influent water the atrazine removal efficiency of the barriers was reduced by almost 60%. This result supports the hypothesis that atrazine was degraded as a source of nitrogen. Poisoning of the biobarriers with mercury chloride resulted in an immediate and large increase in the amount of atrazine in the barrier effluents confirming that biological activity and not abiotic factors were responsible for most of the atrazine degradation. The presence of hydroxyatrazine in the barrier effluents indicated that dehalogenation was one of the pathways of atrazine degradation. Permeable barriers might be formed in-situ by the injection of innocuous vegetable oil emulsions into an aquifer or sandy soil and used to remove atrazine from a contaminated groundwater or to protect groundwater from an atrazine spill.     

Levels of PCDD/F in adipose tissue on non-occupationally exposed subjects living near a hazardous waste incinerator in Catalonia, Spain

The potential adverse effects on human health of hazardous waste incinerators (HWIs) are a subject of concern. The construction of the first and till now only HWI in Spain finished in 1999. In 2007, after approximately 9 years of regular operations in the facility, the concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) were determined by HRGC/HRMS in samples of adipose tissue of 15 autopsied subjects living in the area under potential impact of the HWI (Constantí, Tarragona County, Catalonia). These data were compared with the levels found in two previous surveys performed in 1998 (baseline) and 2002. The current mean PCDD/F concentration in adipose tissue was 14.6 pg WHO-TEQ/g of fat (range: 3.3–55.4 pg WHO-TEQ/g of fat). It means significant changes (a reduction of 64% and an increase of 47%) in the mean PCDD/F levels in comparison to those found in 1998 and 2002: 40.1 and 9.9 pg WHO-TEQ/g of fat, respectively. Women showed higher levels of PCDD/F than men (23.8 vs 11.2 pg WHO-TEQ/g of fat). The increase in the last 5 years would not be directly attributable to exposure to PCDD/F emitted by the HWI, as other biological monitors such as human plasma and milk decreased during the same period.     

Air pollutant concentrations near three Texas roadways, part II: Chemical characterization and transformation of pollutants

Spatial gradients of vehicular emitted air pollutants were measured in the vicinity of three roadways in the Austin, Texas area: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway with significant truck traffic. A mobile monitoring platform was used to characterize the gradients of CO and NO_x concentrations with increased distance from each roadway, while concentrations of carbonyls in the gas-phase and fine particulate matter mass and composition were measured at stationary sites upwind and at one (I-35 and FM-973) or two (SH-71) downwind sites. Regardless of roadway type or wind direction, concentrations of carbon monoxide (CO), nitric oxide (NO), and oxides of nitrogen (NO_x) returned to background levels within a few hundred meters of the roadway. Under perpendicular wind conditions, CO, NO and NO_x concentrations decreased exponentially with increasing distance perpendicular to the roadways. The decay rate for NO was more than a factor of two greater than for CO, and it comprised a larger fraction of NO_x closer to the roadways than further downwind suggesting the potential significance of near roadway chemical processing as well as atmospheric dilution. Concentrations of most carbonyl species decreased with distance downwind of SH-71. However, concentrations of acetaldehyde and acrolein increased farther downwind of SH-71, suggesting chemical generation from the oxidation of primary vehicular emissions. The behavior of particle-bound organic species was complex and further investigation of the size-segregated chemical composition of particulate matter (PM) at increasing downwind distances from roadways is warranted. Fine particulate matter (PM_2.5) mass concentrations, polycyclic aromatic hydrocarbons (PAHs), hopanes, and elemental carbon (EC) concentrations generally exhibited concentrations that decreased with distance downwind of SH-71. Concentrations of organic carbon (OC) increased from upwind concentrations immediately downwind of SH-71 and continued to increase further downwind from the roadway. This behavior may have primarily resulted from condensation of semi-volatile organic species emitted from vehicle sources with transport downwind of the roadway.     

The effects of scale and spatial heterogeneities on diffusion in volcanic breccias and basalts: Amchitka Island, Alaska

Knowledge of the factors that influence the diffusion of contaminants, such as the diffusivity and the connected porosity, is crucial to modeling the long-term fate and transport of contaminants in subsurface systems with small or negligible advective flow, such as in fractured crystalline rock. Fractured rock is naturally heterogeneous, and hence, understanding the diffusivity of a molecule through this material (or the formation factor of the medium) becomes a complex problem, with critical concerns about the scale of laboratory measurements and about the spatial variability of these measurements relative to the scale needed for fate and transport modeling. This study employed both electrical and tracer-based laboratory methods to investigate the effects of scale and pore system connectivity on the diffusivity for volcanic matrix rock derived from the study site, a former underground nuclear test site at Amchitka Island, Alaska. The results of these investigations indicate a relatively well-connected pore system with scale effects generally limited to approximately 6 cm lengths and well-correlated to observed heterogeneous features. An important conclusion resulting from this study, however, is that there is a potential for the estimated diffusivity to be misrepresented by an order of magnitude if multiple samples or longer sample lengths are not used. Given the relatively large number of measurements resulting from these investigations, an analysis of the probability density function (PDF) of the diffusivity was possible. The PDF of the diffusivity was shown to generally follow a normal distribution for individual geologic layers. However, when all of the geologic layers are considered together, the distribution of the subsurface as a whole was shown to follow a lognormal distribution due to the order of magnitude differences amongst the layers. An understanding of these distributions is essential for future stochastic modeling efforts.