白腐菌对芳香族化合物的降解途径

白腐菌 (Whiterotfungi)是目前所发现的对芳香族化合物有很强降解能力的一类微生物。本文探讨了降解芳香族化合物的白腐菌种及其代谢化合物的主要类型 ,分析了对不同化合物的不同代谢途径 ,同时展望了其应用前景     

活性炭-双氧水催化氧化法深度处理DSD酸废水的研究

以活性炭为催化剂、H2O2为氧化剂的催化氧化技术来处理DSD酸母液树脂吸附出水。处理效果比单纯的活性炭吸附或H2O2氧化要好的多。在温度25℃，线速度0．10m／h，pH3．50，H2O2添加量0．35％，处理500mL水样后，脱色率达到90%以上，TOC去除率达到40．0％以上。     

超声-过氧化氢-氧化铜组合技术催化氧化水中苯酚

研究了超声-H2O2-CuO组合技术对苯酚的降解效果。考察了苯酚初始浓度、溶液温度及鼓入空气对苯酚去除率的影响。实验结果表明，与未鼓入空气时相比，连续鼓气时苯酚的降解效果较好；初始浓度低，苯酚去除率高；溶液温度从20％上升到55％时，苯酚去除率随温度升高而增大，温度对该过程的影响主要表现为对催化剂的影响而不是对超声作用的影响。高效液相色谱分析表明，苯酚降解的中间产物主要为对苯二酚、邻苯二酚及其他有机小分子物质，最终产物为草酸、二氧化碳和水。     

生物质废弃物催化裂解制备富氢燃气实验研究

由生物质废弃物催化裂解制取氢气是一种可再生的制氢方法，本研究采用2段加热管式反应器，前段装生物质，后段装催化剂，用以研究生物质催化裂解制取氢气的特性，并提出潜在氢产率的概念对生物质制氢的经济技术可行性进行深入的分析。测试的3种生物质废弃物为：松木粉、木质素和纤维素，测试温度为600～700℃。实验结果表明，加入催化剂后3种物料的产氢率从5．48～15．06g／kg增加到12．94～37．73g／kg；催化剂对潜在产氢率的影响较小，加入催化剂前后的变化范围为：36、25～98、86g／kg到37．40～116．98g／kg。生物质废弃物催化裂解产氢率与相同温度下空气-水蒸气气化的氢产率相当，实验结果证明，生物质废弃物催化裂解是一种有效的制氢方法。     

Investigation of aerosol and gas emissions from a coal-fired power plant under various operating conditions

The concentrations of fine particles and selected gas pollutants in the flue gas entering the stack were measured under several common operation modes in an operating coal power plant producing electricity. Particle size distributions in a diameter range from 10 nm to 20 μm were measured by a scanning mobility particle sizer (SMPS), and the flue gas temperature and concentrations of CO₂ and SO₂ were monitored by a continuous emission monitoring system (CEMS). During the test campaign, five plant operating modes were studied: soot blowing, bypass of flue-gas desulfurization (FGD), reheat burner operating at 0% (turned off), 27%, and 42% (normal condition) of its full capacity. For wet and dry aerosols, the measured mode sizes were both around 40 nm, but remarkable differences were observed in the number concentrations (#/cm³, count per square centimeter). A prototype photoionizer enhanced electrostatic precipitator (ESP) showed improved removal efficiency of wet particles at voltages above +11.0 kV. Soot blowing and FGD bypass both increased the total particle number concentration in the flue gas. The temperature was slightly increased by the FGD bypass mode and varied significantly as the rating of reheat burner changed. The variations of CO₂ and SO₂ emissions showed correlations with the trend of total particle number concentration possibly due to the transitions between gas and particle phases. The results are useful in developing coal-fired power plant operation strategies to control fine particle emissions and developing amine-based CO₂ capture technologies without operating and environmental concerns associated with volatile amine emissions.

Implications: The measurement of the fine particle size distributions in the exhaust gas under several common operating conditions of a coal-fired power plant revealed different response relations between aerosol number concentration and the operating condition. A photo-ionizer enhanced ESP was demonstrated to capture fine particles with higher efficiency compared to conventional ESPs, and the removal efficiency increased with the applied voltage. The characteristic information of aerosols and main gaseous pollutants in the exhaust gas is extremely important for developing and deploying CO₂ scrubbers, whose amine emissions and operating effectiveness depends greatly on the upstream concentrations of fine particles, SO₂, from the power plant.     

The effect of diesel fuel sulfur content on particulate matter emissions for a nonroad diesel generator

The effect of sulfur content on diesel particulate matter (DPM) emissions was studied using a diesel generator (Generac Model SD080, rated at 80 kW) as the emission source to simulate nonroad diesel emissions. A load simulator was used to apply loads to the generator at 0, 25, 50, and 75 kW, respectively. Three diesel fuels containing 500, 2100, and 3700 ppm sulfur by weight were selected as generator fuels. The U.S. Environmental Protection Agency sampling Method 5 "Determination of Particulate Matter Emissions from Stationary Sources" together with Method 1A "Sample and Velocity Traverses for Stationary Sources with Small Stacks or Ducts" was adopted as a reference method for measurement of the exhaust gas flow rate and DPM mass concentration. The effects of various parameters on DPM concentration have been studied, such as fuel sulfur contents, engine loads, and fuel usage rates. The increase of average DPM concentrations from 3.9 mg/Nm3 (n cubic meter) at 0 kW to 36.8 mg/Nm3 at 75 kW is strongly correlated with the increase of applied loads and sulfur content in the diesel fuel, whereas the fuel consumption rates are only a function of applied loads. An empirical correlation for estimating DPM concentration is obtained when fuel sulfur content and engine loads are known for these types of generators: Y = Zm(alphaX + beta), where Y is the DPM concentration, mg/m3, Z is the fuel sulfur content, ppm(w) (limited to 500-3700 ppm(w)), X is the applied load, kW, m is the constant, 0.407, alpha and beta are the numerical coefficients, 0.0118 +/- 0.0028 (95% confidence interval) and 0.4535 +/- 0.1288 (95% confidence interval), respectively.     

Influence of air pollution on the incidence of respiratory tract neoplasm

To evaluate the possible influence of air pollutants on the incidence of respiratory tract neoplasm we studied 12 S?o Paulo City districts where air pollution is observed. We collected data on pollutants from 1981-1990 and correlated it with the incidence of larynx and lung neoplasms in 1997. Ozone was the pollutant that best correlated with the incidence of neoplasm. The correlation coefficients were 0.7234 (p=0.277) and 0.9929 (p=0.007) for lung and larynx cancer, respectively. There may be a relationship between air pollution and the incidence of respiratory tract neoplasm. This study, however, does not allow us to conclude that there is a causal relationship.     

Catalytic decomposition of hydrogen peroxide and 4-chlorophenol in the presence of modified activated carbons

The objective of this research was to examine the heterogeneous catalytic decomposition of H(2)O(2) and 4-chlorophenol (4-CP) in the presence of activated carbons modified with chemical pretreatments. The decomposition of H(2)O(2) was suppressed significantly by the change of surface properties including the decreased pH(pzc) modified with oxidizing agent and the reduced active sites occupied by the adsorption of 4-CP. The apparent reaction rate of H(2)O(2) decomposition was dominated by the intrinsic reaction rates on the surface of activated carbon rather than the mass transfer rate of H(2)O(2) to the solid surface. By the detection of chloride ion in suspension, the reduction of 4-CP was not only attributed to the advanced adsorption but also the degradation of 4-CP. The catalytic activity toward 4-CP for the activated carbon followed the inverse sequence of the activity toward H(2)O(2), suggesting that acidic surface functional group could retard the H(2)O(2) loss and reduce the effect of surface scavenging resulting in the increase of the 4-CP degradation efficiency. Few effective radicals were expected to react with 4-CP for the strong effect of surface scavenging, which could explain why the degradation rate of 4-CP observed in this study was so slow and the dechlorination efficiency was independent of the 4-CP concentration in aqueous phase. Results show that the combination of H(2)O(2) and granular activated carbon (GAC) did increase the total removal of 4-CP than that by single GAC adsorption.     

一种新型国产高效除尘滤筒在船厂分段涂装车间的应用

国产除尘滤材是将聚酯纤维热轧成型 ,再涂敷高分子发泡制成。滤材硬挺、耐压、抗撕裂 ,内部结构稳定 ,粉尘过滤精度高 ,实现表面过滤 ,易清灰再生 ,使用寿命长 ,耐水、酸、碱 ,可广泛用于各工业领域的气体净化和粉尘处理。大连新船重工集团把国产除尘滤材制成的滤筒配置到厂内原有的除尘系统中 ,通过 1年多的使用 ,获得非常满意的除尘效果。从而证明国产滤料性能已达到国际先进水平。