Planning of methane emission control from hoggery using an inexact two-stage optimization model

This study aims to develop an inexact two-stage optimization model to gather manure distributed over the southwest Taiwan and convert it into bioenergy. In the method, local optimization of each hauling zone is performed first using a gray mixed-integer programming model. Then, the hauling zones are prioritized by its performance on four gray scenarios. Although the biogas yield and the manure generation rate are ambiguous, one can easily evaluate his opportunity and risk by gray interval, which is a group of values within the lower and upper bounds. The analyses reveal that the biogas yield dominates the profit in this project, and it leads to the failure of the project when the biogas yield is below the level of 0.2 m³ kg^?1. With the goal of reducing 45% of methane emissions from pig farms, seven hauling zones are required to be developed. The farmers living in these zones from the project get carbon credits ranging from 478 to 3269 ton CO_2eq per year, and the investors own the carbon credits in the range of 3264–11820 ton CO_2eq per year. Through the carbon trading, both the investors and pig farmers are able to make profits by trading their carbon credits.

Implications:Biogas recovered from hoggery can be used as a bioenergy source and mitigate the atmospheric greenhouse effect and global warming. This research develops an inexact two-stage optimization model to evaluate the potential of gathering manure for biogas and converting it into bioenergy. The analyses reveal that the biogas yield dominates the profit in this project, and it leads to the failure of the project when the biogas yield is below the level of 0.2 m³ kg^?1. This study has provided a useful reference for the management of biogas production and carbon trading from hoggery for bioenergy.     

Effects of water-emulsified fuel on a diesel engine generator’s thermal efficiency and exhaust

Water-emulsified diesel has proven itself as a technically sufficient improvement fuel to improve diesel engine fuel combustion emissions and engine performance. However, it has seldom been used in light-duty diesel engines. Therefore, this paper focuses on an investigation into the thermal efficiency and pollution emission analysis of a light-duty diesel engine generator fueled with different water content emulsified diesel fuels (WD, including WD-0, WD-5, WD-10, and WD-15). In this study, nitric oxide, carbon monoxide, hydrocarbons, and carbon dioxide were analyzed by a vehicle emission gas analyzer, and the particle size and number concentration were measured by an electrical low-pressure impactor. In addition, engine loading and fuel consumption were also measured to calculate the thermal efficiency. Measurement results suggested that water-emulsified diesel was useful to improve the thermal efficiency and the exhaust emission of a diesel engine. Obviously, the thermal efficiency was increased about 1.2 to 19.9%. In addition, water-emulsified diesel leads to a significant reduction of nitric oxide emission (less by about 18.3 to 45.4%). However, the particle number concentration emission might be increased if the loading of the generator becomes lower than or equal to 1800 W. In addition, exhaust particle size distributions were shifted toward larger particles at high loading. The consequence of this research proposed that the water-emulsified diesel was useful to improve the engine performance and some of exhaust emissions, especially the NO emission reduction.

Implications:The accumulated test results provide a good basis to resolve the corresponding pollutants emitted from a light-duty diesel engine generator. By measuring and analyzing transforms of exhaust pollutant from this engine generator, the effects of water-emulsified diesel fuel and loading on emission characteristics might be more clear. Understanding reduction of pollutant emissions during the use of water-emulsified diesel helps improve the effectiveness of the testing program. The analyzed consequences provide useful information to the government for setting policies to curb pollutant emissions from a light-duty diesel engine generator more effectively.     

纳米TiO2-石墨烯光催化剂的水热合成及其光催化性能

以钛酸四正丁酯和石墨为原料,通过水热法制备了锐钛矿型为主的纳米TiO2复合光催化剂（纳米TiO2-石墨烯）,并采用XRD,FTIR,FESEM,TEM技术对其进行了表征。通过紫外光照射降解溶液中的罗丹明B（RhB）研究了TiO2-石墨烯的光催化活性,分析了初始罗丹明B质量浓度、催化剂加入量、溶液pH和催化剂使用次数等影响降解效果的因素。实验结果表明：在初始RhB质量浓度为20 mg/L、溶液pH为7.10、催化剂加入量为1.000 g/L的条件下,紫外光照射30 min时,纳米TiO2-石墨烯对RhB的降解率高达98.69%,明显高于纳米TiO2的44.69%;纳米TiO2-石墨烯稳定性较强,可多次重复使用。     

A2O-MBR工艺处理城市污Z作农业灌溉用水中试研究

为开发一种污水再生利用于农田灌溉领域的新型技术,本实验以城市污水为研究对象,采用A2O—MBR工艺进行中试研究,并将系统出水水质与《农田灌溉水质标准（GB5084—2005）》的主要水质指标进行对比分析。结果表明,系统COD和BOD,出水浓度范围分别为3．2～59．6mg／L、1．0～7．6mg／L,系统出水pH为7．16～7．54,悬浮物浓度几乎为0,上述指标均符合标准;TP、TN和氨氮的出水范围分别为0．03～0．79mg／L、1．6～17．7mg／L和0．8～10．3mg／L。《农田灌溉水质标准》没有对上述3个指标提出具体要求,且少量的氮磷是植物生长的营养元素。该系统出水的主要水质指标符合标准兽求．     

高效脱硫菌的筛选及其性能研究

从高硫污染的活性污泥中富集培养,分离纯化得到一株可以降解噻吩的菌株s_4,并对该菌株的形态特征进行观察。应用Design—Expert8．0．5b软件进行响应面优化实验,研究了反应时间、噻吩浓度、微生物浓度3个因素的组合对菌株s_4脱硫效果的影响,并拟合得到多元二次回归方程,得出最佳实验条件。拟合结果表明,当反应时间27．46h,噻吩浓度为1．04％,微生物浓度4．04％时,预测噻吩降解率为14．8％,通过验证得最佳条件下的降解率为14．3％,与预测值相符。     

表面活性剂改性4A分子筛对Cr(VI)的吸附行为

采用浸渍法对4A分子筛进行表面改性,通过引入阳离子表面活性剂,使4A分子筛表面附着季铵型阳离子,并与反离子Br-形成"阴离子交换膜",从而促使更多的Cr(VI)阴离子通过离子交换吸附到改性4A分子筛上,通过X-射线衍射(XRD)和傅里叶变换红外光谱(FTIR)对样品的物相结构和组成进行表征分析。研究表明,表面活性剂的类型和疏水碳氢链结构会影响4A分子筛的吸附能力,十八烷基三甲基溴化铵(OTAB)碳氢链长,在分子筛表面形成的双分子层密,对Cr(VI)的吸附量最大。采用准一级、准二级、Elovich和Bangham动力学模型对六价铬的吸附数据进行拟合,其中准一级动力学方程最符合十八烷基三甲基溴化铵改性分子筛的吸附行为。同时,分别从Langmuir和Redlich-Peterson等温吸附模型获得六价铬的最大吸附量为13.98 mg/g,且改性分子筛以均一表面吸附为主。     

柴油机微粒中可溶性有机成分的真空干燥条件

柴油机碳烟颗粒(PM)中可溶性有机组分(SOF)含量是其重要的特性参数,而真空干燥法可方便、高效、可靠地分析颗粒SOF含量,对其干燥条件的探索具有重要的研究意义和应用价值。首先采用模拟的柴油机颗粒,分析不同的干燥条件对模拟SOF(柴油、润滑油)挥发率的影响规律,得出模拟的SOF分析的最佳干燥条件;在此基础上,探索了真实柴油机颗粒SOF分析的最佳干燥条件为:干燥温度220℃、干燥时间3 h、真空度98 kPa,得知SOF组分干燥的难易程度介于柴油和润滑油之间;同时,根据此干燥条件,分析了排气管末端采集的真实碳烟颗粒的SOF含量特性。     

The fate and risk of selected pharmaceutical and personal care products in wastewater treatment plants and a pilot-scale multistage constructed wetland system

The removal of 12 pharmaceuticals and personal care products (PPCPs) in two full-scale wastewater treatment plants (WWTPs) and a tertiary treatment system was studied. The ecological risks of effluents from both secondary and tertiary treatment systems as well as excess sludge were evaluated. Primary treatment and ultraviolet light disinfection showed limited ability to remove most selected PPCPs. The combination of an anaerobic process and triple-oxidation ditches can eliminate DEET better than the anaerobic/anoxic/oxic process. Adsorption to sludge played a key role in the removal of triclocarban. Multistage constructed wetlands as a tertiary treatment efficiently removed caffeine and ibuprofen from wastewater and could decrease the risk of partial selected PPCPs. Selected PPCPs residues in excess sludge generally produced higher risks to the ecological environment than effluents from WWTPs.     

Characterization of the interactions between tetracycline antibiotics and microbial extracellular polymeric substances with spectroscopic approaches

The antibiotics have attracted global attentions for their impact on aquatic ecosystem. The knowledge about the fate of antibiotics encountering extracellular polymeric substances (EPS) is, however, limited. In this study, we investigated the interacting mechanisms of tetracycline (TC) to EPS extracted from aerobic activated sludge. The contributions of the main components of EPS, extracellular proteins, and polysaccharides were evaluated using bovine serum albumin and alginate sodium, respectively. Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and nuclear magnetic resonance indicated that hydroxyl, carboxyl, and amino groups were the domain chemical groups involved in the interaction between TC and EPS, and the binding of TC onto EPS changed the structure of these chemical groups, thus causing shifts in their UV–visible absorption spectra. In addition, we found that extracellular proteins, rather than polysaccharides, were the major active contents involved in the interaction. Three-dimensional excitation–emission matrix fluorescence spectroscopy showed that the fluorophores in EPS were clearly quenched by TC and the static quenching process was observed, implying the complex formation of TC and EPS. Furthermore, thermodynamic analysis indicated that the binding of TC with EPS is spontaneous and dominated by electrostatic forces.     

Rapid and efficient removal of Ni2+ from aqueous solution by the one-pot synthesized EDTA-modified magnetic nanoparticles

A facile one-pot process has been proposed to prepare the novel ethylenediaminetetraacetic acid (EDTA)-modified magnetite nanoparticles (EDTA-MNPs). The bared Fe₃O₄ magnetite nanoparticles and EDTA-MNPs were characterized using FTIR spectroscopy, TEM, VSM, and X-ray diffraction. The application of the modified magnetite nanoparticles for metal ion uptake was studied using Ni²⁺ as a model. The adsorption was fast and the equilibrium was established within 5 min, and the adsorption kinetics of Ni²⁺ onto EDTA-MNPs followed the pseudo second-order chemisorption mechanism. Maximum adsorption capacity for Ni²⁺ reached as high as 41.3 mg/g at pH 6. The successive adsorption–desorption studies indicated that the EDTA-MNPs kept the adsorption and desorption efficiencies constant over ten cycles. Importantly, EDTA-MNPs were able to remove nearly 100 % of Ni²⁺ from real water.