粉末活性污泥处理含铀废水的特性

以生活污水处理厂剩余活性污泥为原料,制备粉末活性污泥(PAS)作为生物吸附剂,考察pH值,PAS投加量,U(Ⅵ)初始浓度和吸附时间对PAS吸附U(Ⅵ)的影响,探讨了PAS吸附U(Ⅵ)的作用机理。实验结果表明,在U(Ⅵ)初始浓度为10 mg/L时,其最佳吸附pH值为3,去除率97.77%,吸附平衡时间120 min;吸附过程较好地拟合了准二级动力学模型(R2≈1)和Freundlich等温模型(R2≈1);X射线能谱和离子交换实验分析表明,离子交换为其主要吸附方式,参与交换的主要离子为Ca2+;红外光谱分析表明,PAS吸附U(Ⅵ)后自身结构未发生改变。以0.1 mol/L的HCl溶液作为解吸液,初次解吸率达92.83%,循环利用3次仍具有较好的吸附效果。     

大气压等离子体射流对水中铜绿微囊藻的灭活作用

以铜绿微囊藻为研究对象,将空气源大气压等离子体射流(APPJ)引入到液相,构建新型的大气压等离子体射流液相反应体系,考察了不同APPJ处理方式对铜绿微囊藻的灭活效率,观察了放电处理的藻细胞形态,分析了培养基pH的变化和液相产生的主要活性物质(H2O2和O3)对藻灭活的作用,并探讨了APPJ灭活铜绿微囊藻的作用机理。研究结果表明,当电压为7 kV,空气气体流速为4 L/min,藻液吸光度约为0.200,铜绿微囊藻的灭活率达到99.16%;处理后的藻发生细胞变形和破裂;处理后的藻液中产生H2O2和O3等活性物质,同时产生大量的NO3-和NO2-离子,导致液相pH迅速下降。通过考察主要活性物质(H2O2和O3)及藻液pH因素发现,单一因素灭活效果不佳,主要活性物质(H2O2和O3)和pH的组合因素是APPJ灭活水中铜绿微囊藻的主要原因。     

低温碱溶脱除液晶显示器(LCD)玻璃基板粉末中的硅和铝

为了提高氯化法回收LCD中铟的效果,降低SiO2和Al2O3对氯化过程的干扰,采用NaOH对液晶显示器玻璃基板粉末中的硅和铝进行了预先溶出规律研究.首先分析了LCD粉末中SiO2和Al2O3的含量、形貌以及铟的浸出变化,然后计算了SiO2和Al2O3的脱除效率.在条件实验基础上通过正交实验设计得出优化实验条件.研究表明,在液固比为90:2、温度95℃、溶出时间2 h、碱度0.56 g/L的最佳工艺条件下, SiO2的脱除率为80.88%、Al2O3的脱除率为 83.30%、二者总的脱除率为81.30%,洗涤液中没有发现铟的溶出,碱溶后的物料表面产生大量均匀的孔状结构.这将对液晶显示器玻璃基板粉末的资源化与铟的富集有重要意义.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9%~5.4%.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3%的系统脱硫效率整体高于含湿量为5%和4%的样品,最大值达93.56%.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3%的循环脱硫灰较含湿量为5%的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5%样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaSO3干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

页岩对污泥氨气挥发的抑制作用

氨气是城市污水污泥产生的恶臭气体之一,控制或抑制其产生是资源化利用甚至处置过程中至关重要的.通过改进氨气测量方法定量分析外掺页岩对污泥氨气挥发的抑制作用和机理,实验研究了页岩掺量、陈放形式以及环境温度对污泥氨气挥发浓度的影响.结果表明,外掺页岩对污泥氨气挥发具有明显的抑制作用,随温度升高、陈放时间延长抑制效果有所减弱但仍具有明显作用;页岩对污泥氨气挥发的抑制作用主要为对氨气的吸附作用.     

厌氧系统中碱处理对污泥减量的影响

碱解预处理污泥和原污泥按一定比例进行混合后,投入厌氧反应器中进行消化,研究其对污泥减量化的影响。结果表明,该处理既可以提高污泥减量率,又能改善污泥厌氧消化性能,提高污泥产气量。当碱处理污泥和原污泥混合比为1∶3时,在混合初期由于稀释作用和水解中和作用,溶液的pH能迅速恢复到中性。SS减少48%,较对照组提高了10%;SCOD减少约80%,较对照组提高20%,而空白对照组因未发生溶胞作用,各参数值均处于较低水平,降解率也维持在较低水平。     

直接投菌法在城市重污染河流治理中的应用研究

在无截污和清除内源的情况下,对深圳市甘坑河采用梅花式接种法将本源微生物菌剂分两次直接接入河流水体及底泥中。结果表明,第1次接种后的4 d内各项水质指标都不稳定,4 d后,悬浮物、COD、TP和NH3-N等浓度下降,水质明显改善;但从第8天开始,COD、NH3-N和TP的去除率同时下降,本源微生物的处理效率开始降低,需进行第2次接种;第2次接种后,DO浓度提升至2.0 mg/L以上,COD、TP和NH3-N的去除率分别保持在40%、30%和40%以上。结果表明,直接投菌法在城市重污染河道治理中可以初步消除河道的黑臭现象,修复水质。     

Long-Term Operation of a Biofilter for Simultaneous Removal of H2S and NH3

Abstract

Simultaneous removal of NH₃ and H₂S was investigated using two types of biofilters—one packed with wood chips and the other with granular activated carbon (GAC). Experimental tests and measurements included analyses of removal efficiency (RE), metabolic products, and results of long-term operation (around 240 days). The REs for NH₃ and H₂S were 92 and 99.9%, respectively, before deactivation. After deactivation, the RE for NH₃ and H₂S were decreased to 30–50% and 75%, respectively. The activity of nitrifying bacteria was inhibited by high concentrations of H₂S (over 200 ppm) but recovered gradually after H₂S addition was ceased. However, the Thiobacillus thioparus as sulfur oxidizing bacteria did not show inhibition at the NH₃ concentration under 150-ppm conditions. The deactivation of the biofilter was caused by metabolic products [elemental sulfur and (NH₄)₂SO₄] ac-cumulating on the packing materials during the extended operation. The removal capacities for NH₃ and H₂S were 6.0–8.0 and 45–75 mg N, S/L/hr, respectively.     

高层建筑火灾人员疏散和人员伤亡的模拟

基于建筑火灾全风网网络模型的基础上 ,结合紧急疏散模型 ,模拟火灾时期疏散时间和建筑物内人员滞留的情况 ,同时也可以模拟可能出现的伤亡情况 ,有助于高层建筑的疏散系统设计 ,为火灾的再现提供了一个有效的分析工具 ,也为高层建筑火灾的风险评价提供了理论数据     

Two-step fast microwave-assisted pyrolysis of biomass for bio-oil production using microwave absorbent and HZSM-5 catalyst

A novel technology of two-step fast microwave-assisted pyrolysis(f MAP) of corn stover for bio-oil production was investigated in the presence of microwave absorbent(Si C) and HZSM-5catalyst. Effects of f MAP temperature and catalyst-to-biomass ratio on bio-oil yield and chemical components were examined. The results showed that this technology, employing microwave, microwave absorbent and HZSM-5 catalyst, was effective and promising for biomass fast pyrolysis. The f MAP temperature of 500°C was considered the optimum condition for maximum yield and best quality of bio-oil. Besides, the bio-oil yield decreased linearly and the chemical components in bio-oil were improved sequentially with the increase of catalyst-to-biomass ratio from 1:100 to 1:20. The elemental compositions of bio-char were also determined. Additionally, compared to one-step f MAP process, two-step f MAP could promote the bio-oil quality with a smaller catalyst-to-biomass ratio.