Treatment of 1,3-Butadiene in an Air Stream by a Biotrickling Filter and a Biofilter

ABSTRACT

This paper presents results obtained from a performance study on the biotreatment of 1,3-butadiene in an air stream using a reactor that consisted of a two-stage, in-series biotrickling filter connected with a three-stage, in-series biofilter. Slags and pig manure-based media were used as packing materials for the biotrickling filter and the biofilter, respectively. Experimental results indicated that, for the biotrickling filter portion, the butadiene elimination capacities were below 5 g/m³/hr for loadings of less than 25 g/m³/hr, and the butadiene removal efficiency was only around 17%. For the biofilter portion, the elimination capacities ranged from 10 to 107 g/m³/hr for loadings of less than 148 g/m³/hr. The average butadiene removal efficiency was 75–84% for superficial gas velocities of 53–142 m/hr and a loading range of 10–120 g/m³/hr. The elimination capacity approached a maximum of 108 g/m³/hr for a loading of 150 g/m³/hr. The elimination rates of butadiene in both the biotrickling filter and biofilter were mass-transfer controlled for influent butadiene concentrations below about 600 ppm for superficial gas velocities of 29–142 m/hr. The elimination capacity was significantly higher in the biofilter than in the biotrickling filter. This discrepancy may be attributed to the higher mass-transfer coefficient and gas-solid interfacial area offered for transferring the gaseous butadiene in the biofilter.     

Development of Thixotropic Coatings Using Dimerized Soybean Oil Fatty Acids: The Case of Polyamide of 1,2-Phenylene Diamine

Soybean oil (SBO) was dimerized and the crude dimer acid product reacted with 1,2-phenylene diamine at 210 ± 5 °C under inert atmosphere to obtain fatty polyamide (FPA). The FPA was used to modify a commercial alkyd resin by reacting a mixture of the alkyd resin with 5 wt% of FPA at 120 °C for 80 min under inert atmosphere. The FTIR spectrum of the FPA modified resin showed evidence of higher degree of H-bonding than was found for the unmodified alkyd. White gloss coatings of 15, 20, 25, and 30% solids were formulated from the modified and unmodified resins and examined for performance with respect to: leveling, sag resistance, drying time, pigment settling, skinning tendency and film hardness. Results showed that the unmodified alkyd coatings exhibited good leveling but poor sag resistance at all solid contents. In contrast, FPA modified alkyd coatings combined good leveling with high sag resistance indicating their thixotropic nature. A strong tendency to pigment settling was observed for unmodified alkyd coatings but was not observed in the FPA modified alkyd coatings. The modified alkyd coatings showed skinning while the unmodified alkyd coatings did not skin. A 30% solids coating formulation of the FPA modified resin showed shorter surface dry time but longer hard dry time than the unmodified alkyd resin coating.     

Food Aid and the Famine Relief Argument (Brief Return)

Recent publications by Pogge (Global ethics: seminal essays. St. Paul: Paragon House 2008) and by Singer (The life you can save: acting now to end world poverty. New York: Random House 2009) have resuscitated a debate over the justifiability of famine relief between Singer and ecologist Garrett Hardin in the 1970s. Yet that debate concluded with a general recognition that (a) general considerations of development ethics presented more compelling ethical problems than famine relief; and (b) some form of development would be essential to avoiding the problems of growth noted by Hardin. Better than renewing the debate, we should recognize two points. First, food needs do indeed evoke a moral response that is more direct and compelling than the philosophical positions often generated to rationalize a duty to bring aid. As such the argument for feeding hungry people cannot be generalized into a paradigm for development ethics without distortions that undercut the morally valid elements in Singer’s original argument. Second, contrary to prevailing assumptions in present day development ethics, food aid and famine relief continue to be important priorities for international agencies, notably the World Food Program. Emergency food assistance, the nominal topic of Singer’s original article, thus is an important issue for agricultural as well as development ethics, though one that should indeed be seen as distinct from more complex duties to address the conditions of chronic poverty and underdevelopment.     

Bio-immobilization of Cu and Zn in recirculated bioreactor landfill

Purpose  

To protect the environmental quality of soil, groundwater, and surface water near the landfill site, it is necessary to make an accurate assessment of the heavy metal mobility. This study aims to present the bio-immobilization behavior of heavy metals in landfill and provide some reference suggestion for the manipulation of heavy metal pollution control after closure.     

甲基氯硅烷生产废液制备氯化氢和有机硅树脂

研究了将高、低沸点甲基氯硅烷生产废液分别通过醇解和水解反应制备HCl和有机硅树脂的工艺方法,考察了醇解时间、醇解温度和m(废液)∶m(甲醇)等因素对产物收率的影响.实验得到最佳反应条件为:m(废液)∶m(甲醇)=1∶0.5,醇解温度65℃,醇解时间2h.在该条件下由高、低沸点废液制得的有机硅树脂收率分别为43.2％和40.6％.将制得的有机硅树脂经500℃干燥处理后,可作为填料,制备有机硅树脂-聚氯乙烯复合材料.该材料的力学性能与SiO2 -聚氯乙烯复合材料接近.     

A study on legislative and policy tools for promoting the circular economic model for waste management in China

The circular economy has been developing rapidly in recent years in China. A legislative system has been created to provide legal protection for the development of a circular economy, including a series of price and tax measures in the waste management area. These measures form the basic foundation for promoting better waste management under the circular economic model. Many challenges, however, remain. For instance, the legal system needs to incorporate more sophisticated science, and China lacks key waste treatment technology that could support the further development of a circular economy. There is also a need to educate the public about the concept of the circular economy and its benefits. Specific suggestions are made for the development and implementation of the circular economic model.     

The effect of the addition of fly ash to municipal digested sludge on its electroosmotic dewatering

Effective handling of municipal digested sludge requires that the product cake have low water content. To this end, we investigated the change in sludge dewaterability after the addition of fly ash to municipal digested sludge, dewatering of which is difficult because of its high organic content. The performance of the dewatering is compared with that of electroosmotic dewatering (EDW) and conventional mechanical dewatering (CMD). Fly ash classified by sieving to the size of 25–75 μm and >75 μm is added to the municipal digested sludge by 10, 20, and 50 wt% by wet base. When adding fly ash particles to municipal digested sludge, dewatering efficiency improved with smaller fly ash particle size and with increase in the amount. When sludge was dewatered using an electroosmotic dewatering method, the dewatering efficiency is improved about 40% by adding fly ash of 25–75 μm particle size with 20 wt% when compared with conventional mechanical dewatering method without adding the fly ash. It is concluded that fly ash particles rich in inorganic material are helpful in the dewatering process when added to municipal digested sludge and EDW is more effective than CDW.     

Archaeal Poly (3-hydroxybutyrate) Polymer Production from Glycerol: Optimization by Taguchi Methodology

In this study the possibility of poly (3-hydroxybutyrate) production from glycerol was investigated and optimized by Halorcula sp. IRU1, a novel archaea isolated from Urmia lake, Iran in batch experiments. Using Taguchi methodology, three important independent parameters (glycerol, yeast extract and KH₂PO₄) were evaluated for their individual and interactive effects on poly (3-hydroxybutyrate) production. It was shown that the glycerol concentration was the most significant factor affecting the yield of poly (3-hydroxybutyrate). The optimum factor levels were a glycerol concentration of 8% (v/v), yeast extract 0.8% (w/v) and KH₂PO₄ 0.002% (w/v). The predicted value obtained for poly (3-hydroxybutyrate) production under these conditions was about 81.87%. We can conclude that Haloarcula sp. IRU1 has a high potential for synthesis of poly (3-hydroxybutyrate) from glycerol.     

Preformed Amide-containing biopolymer for Improving the Environmental Performance of Synthesized Urea–formaldehyde in Agro-fiber Composites

Investigations have continued for production high performance agro-based composites using environmentally acceptable approaches. This study examines the role of adding amide-containing biopolymers during synthesis of urea–formaldehyde (UF) on properties of adhesive produced, especially its adhesion potential. The environmental performance of UF-resin synthesized in the presence of modified amide-containing biopolymer was evaluated by evaluating the free-HCHO of both adhesive (during processing) and of the eventual engineered composite product. Also, the benefits of this synthesis-modified adhesive in enhancing the bondability of sugar-cane fibers used in engineered composite panels was evaluated and compared to using UF-resin. The results obtained show that, static bending of the produced composites varied from 27.7 to 33.13 N/mm² of modulus of rupture (MOR) and from 2860 to 3374 N/mm² of Modulus of Elasticity (MOE); while for internal bond (IB) it’s varied from 0.64 to 0.866 N/mm². Based on the ANSI and EN Standards modified UF-based agro composites produced meet the performance requirements for high grade particleboards with respect to static bending strength. These agro-based composite also tested out as having free-HCHO values of ~13 mg/100 g board.