Experimental and numerical study of the dispersion of motor vehicle pollutants under idle condition

The aim of the work presented here is to study experimentally and numerically the dispersion characteristics of vehicular exhaust plume at an idle condition in an idealized and simplified environment. The gaseous and particulate concentrations in the exhaust plume of three idling motor vehicles were measured in an isolated environment under calm weather conditions. Despite the difference in the initial concentrations, the pollutants decayed exponentially in all directions.The CFD code PHOENICS 3.3, with the k–ε eddy dissipation sub-model, was used for the numerical simulation. The simulated results match very well with the experimental results close to the source of emission but decay to the ambient concentrations much slower. The effects of the initial emission concentration, exit velocity, exit direction and crosswind intensity have been investigated parametrically. The initial pollutant concentration will increase the local concentrations but the pattern of dispersion remains the same. The exit velocity will increase the momentum of the jet, resulting in a deeper penetration downstream. The exit angle has a stronger influence on pollutant dispersion than both initial pollutant concentration and exit velocity. When the exit angle is 15°, the pollutants tend to spread on the ground region. Crosswind shows a significant effect on the dispersion of the exhaust plume also. It will divert the plume to disperse in the same direction of the wind with limited penetration in the downstream direction.     

A triple-continuum approach for modeling flow and transport processes in fractured rock

This paper presents a triple-continuum conceptual model for simulating flow and transport processes in fractured rock. Field data collected from the unsaturated zone of Yucca Mountain, a repository site of high-level nuclear waste, show a large number of small-scale fractures. The effect of these small fractures has not been considered in previous modeling investigations within the context of a continuum approach. A new triple-continuum model (consisting of matrix, small-fracture, and large-fracture continua) has been developed to investigate the effect of these small fractures. This paper derives the model formulation and discusses the basic triple-continuum behavior of flow and transport processes under different conditions, using both analytical solutions and numerical approaches. The simulation results from the site-scale model of the unsaturated zone of Yucca Mountain indicate that these small fractures may have an important effect on radionuclide transport within the mountain.     

Application and evaluation of two air quality models for particulate matter for a southeastern U.S. episode

The Models-3 Community Multiscale Air Quality (CMAQ) Modeling System and the Particulate Matter Comprehensive Air Quality Model with extensions (PMCAMx) were applied to simulate the period June 29-July 10, 1999, of the Southern Oxidants Study episode with two nested horizontal grid sizes: a coarse resolution of 32 km and a fine resolution of 8 km. The predicted spatial variations of ozone (O3), particulate matter with an aerodynamic diameter less than or equal to 2.5 microm (PM2.5), and particulate matter with an aerodynamic diameter less than or equal to 10 microm (PM10) by both models are similar in rural areas but differ from one another significantly over some urban/suburban areas in the eastern and southern United States, where PMCAMx tends to predict higher values of O3 and PM than CMAQ. Both models tend to predict O3 values that are higher than those observed. For observed O3 values above 60 ppb, O3 performance meets the U.S. Environmental Protection Agency's criteria for CMAQ with both grids and for PMCAMx with the fine grid only. It becomes unsatisfactory for PMCAMx and marginally satisfactory for CMAQ for observed O3 values above 40 ppb. Both models predict similar amounts of sulfate (SO4(2-)) and organic matter, and both predict SO4(2-) to be the largest contributor to PM2.5. PMCAMx generally predicts higher amounts of ammonium (NH4+), nitrate (NO3-), and black carbon (BC) than does CMAQ. PM performance for CMAQ is generally consistent with that of other PM models, whereas PMCAMx predicts higher concentrations of NO3-, NH4+, and BC than observed, which degrades its performance. For PM10 and PM2.5 predictions over the southeastern U.S. domain, the ranges of mean normalized gross errors (MNGEs) and mean normalized bias are 37-43% and -33-4% for CMAQ and 50-59% and 7-30% for PMCAMx. Both models predict the largest MNGEs for NO3- (98-104% for CMAQ 138-338% for PMCAMx). The inaccurate NO3- predictions by both models may be caused by the inaccuracies in the ammonia emission inventory and the uncertainties in the gas/particle partitioning under some conditions. In addition to these uncertainties, the significant PM overpredictions by PMCAMx may be attributed to the lack of wet removal for PM and a likely underprediction in the vertical mixing during the daytime.     

废水除磷技术的研究与发展

目前 ,人们越来越重视污水除磷技术。本文介绍与评述了化学和生物两种除磷方式及其除磷机理和工艺 ,并着重介绍了生物除磷的现状、发展和研究动向     

混凝-生物接触氧化法处理城市污水的研究

采用混凝-生物接触氧化法处理生活小区废水,考察了不同混凝剂用量对COD、NH4-N、SS、TP的去除效果,同时研究了生物接触氧化法对COD、NH4-N等的去除以及耐冲击负荷能力.结果表明,随混凝剂用量的增加,COD、SS、TP的去除率随之增加,生物接触氧化法具有较高的抗冲击负荷能力,最大NH4-N去除负荷达到0.55 kg/(m3·d),最大有机去除负荷达到4.32 kg/(m3·d)     

含重金属水处理污泥的固化和浸出毒性研究

工业危险固体废物在进行安全填埋前需要进行固化稳定处理。针对电镀厂和皮革厂含重金属的水处理污泥 ,用不同比例的水泥、粉煤灰进行固化稳定处理。考虑酸雨环境 ,浸出实验采用TCLP标准。电镀厂污泥单独固化时 ,其浸出液中铜离子浓度由 78 0mg/L下降到 1 5mg/L ;镍离子浓度由 2 2 4 5mg/L下降到 2 2 2mg/L ,高于危险废物允许进入填埋区 15mg/L的控制限值。电镀厂污泥与皮革厂污泥混合后固化 ,浸出液毒性明显降低。铜离子的浸出浓度降低到1 98mg/L ,镍离子降低到 4 10mg/L ,总铬降低到 0 4 0mg/L ,各项指标均低于国家危险废物允许进入填埋区的控制限值 ,可安全填埋。